Sealey PPF20 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
Familiarise yourself with the applications, limitations and hazards
9
of the press.
Maintain the press in good condition (use an authorised service
9
agent).
Replace or repair damaged parts. Use recommended parts only.
9
Unauthorised parts may be dangerous and will invalidate the
warranty.
Keep the press clean for best and safest performance.
9
Locate the press in a suitable work area, on a surface that is
9
stable, level, dry, not slippery, and capable of sustaining the load.
Keep area clean and tidy and free from unrelated materials, and
9
ensure there is adequate lighting.
WARNING! Always wear approved eye or face protection when
‰
operating the press.
Remove ill fitting clothing. Remove ties, watches, rings and other
9
loose jewellery, and contain long hair.
Keep hands and body clear of the work table when operating the
9
press.
Maintain correct balance and footing. DO NOT over reach. Ensure
9
the floor is not slippery and wear non-slip shoes.
Keep children and unauthorised persons away from the working
9
area.
DO NOT use the press for a task it is not designed to perform.
8
DO NOT adjust or tamper with the safety valve, or make any modifications to the press.
8
DO NOT exceed the rated capacity of the press. Avoid applying excessive force, use the pressure gauge to determine the applied load.
8
DO NOT apply off-centre loads. Ensure that workpiece is centrally loaded and correctly secured before operating the press.
8
DO NOT allow the workpiece or the arbor plates to fall from the press work bench.
8
DO NOT get the press wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT operate the press when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT climb upon the press.
8
DO NOT use if bent, broken, cracked, leaking or otherwise damaged, or if press has been subjected to a shock load.
8
DO NOT operate the press if any parts are missing as this may cause failure and/or possible personal injury.
8
DO NOT use the press to compress a spring or any other item that could disengage and cause a potential hazard.
8
DO NOT stand directly in front of loaded press and never leave loaded press unattended.
8
DO NOT allow untrained persons to operate the press.
8
▲ DANGER! This model is purpose designed to withstand greater loads than the hydraulic unit can develop. For safety reasons, always
ensure the workpiece and press tools are secured on the table and will not flex or suddenly give way, causing danger to operator or
the workpiece.
WARNING! DO NOT use brake fluid, or any fluid other than a good quality jack oil, such as SEALEY HYDRAULIC JACK OIL, as this
‰
may cause serious damage to the press and will invalidate the warranty.
When not in use, release pressure from the pump and clean the press. Stand or store the arbors in a safe, childproof location.
9
2. INTRODUCTION
Manufactured in Europe, a Professional range of floor and bench mount presses, ranging from 15tonne to 50tonne. Hydraulic elements are
mounted in the frame to maximise workspace and protect components. Floor models incorporate a fast approach feature (foot pedal or handle
operated depending on model). Model No's PPF301 and PPF501 are air/hydraulic and fully operated by foot pedal to keep hands free for fine
positioning of the workpiece. Storage for press pins included in frame (pins not included on Model No's PPB15, PPF20 and PPF30). Suitable
for workshop use or by the serious motoring enthusiast.
© Jack Sealey Limited
PREMIER HYDRAULIC PRESS
20 & 30TONNE FLOOR TYPES
PPF20 / PPF30
MODEL NO:
Original Language Version PPF20 / PPF30 | Issue 2 (H,F,S,3) 07/06/19