Table of Contents
Advertisement
Quick Links
Operator Cooling Fan
Groundsmaster
Sunshade
Model No. 03247
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
or Reelmaster
Description
No parts required
No parts required
No parts required
Long fan-mount bracket
Cooling fan
Short fan-mount bracket
Carriage bolt (1/4 x 5/8 inch)
Flange locknut (1/4 inch)
Fan switch
Jam nut
Knob
Fan-speed controller
Thread-forming screw (#8 x 3/8 inch)
Wire harness
Cable ties
Fuse (25 A)
No parts required
No parts required
No parts required
Register at www.Toro.com.
Form No. 3430-932 Rev A
®
Traction Unit with Universal
Installation Instructions
Qty.
–
Prepare the machine.
–
Remove the sunshade.
–
Install the switch panel kit.
1
1
1
4
4
Install the cooling fan, fan-speed
controller, and switch.
1
1
1
1
2
1
4
Install the wire harness.
1
–
Connect the battery.
–
Adjust the cooling fan position.
–
Install the sunshade.
Original Instructions (EN)
All Rights Reserved *3430-932* A
Printed in the USA
Use
Advertisement
Table of Contents
Related Manuals for Toro 03247
Summary of Contents for Toro 03247
- Page 1 Form No. 3430-932 Rev A Operator Cooling Fan Groundsmaster ® or Reelmaster ® Traction Unit with Universal Sunshade Model No. 03247 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty.
-
Page 2: Preparing The Machine
Preparing the Machine No Parts Required Procedure Park the machine on a level surface. Shut off the engine, engage the parking brake, and remove the key from the ignition switch. Disconnect the battery; refer to the electrical system maintenance section of your Operator’s Manual. -
Page 3: Installing The Cooling Fan
Align the holes in the fan mount brackets to the hole in the switch panel as shown in Figure Installing the Cooling Fan, Fan Switch, and Fan-Speed Controller Parts needed for this procedure: Long fan-mount bracket Cooling fan Short fan-mount bracket Carriage bolt (1/4 x 5/8 inch) Flange locknut (1/4 inch) Fan switch... - Page 4 Insert the fan-switch shaft through the hole in the panel and secure the switch with the jam nut (Figure Align the D-shaped hole in the knob with the flat Installing the Wire Harness on the inner shaft of the fan-switch shaft (Figure and Fuse Press the knob onto the switch until knob is fully...
- Page 5 g244634 Figure 10 g283647 Figure 8 1. 5-socket connector (kit 3. 2-socket connector wire harness) (cooling-fan harness) 1. Violet (wire-harness 6. Blade terminal 5—Motor (fan-speed controller) terminal labeled R ESISTOR 2. 2-pin connector (kit wire 4. Fan switch ODULE harness) 2.
-
Page 6: Installing The Fuse
Note: The fuse may not need to be installed if a fuse steps: has already been installed from another Toro kit. Shut off the cooling fan. Remove the 4 carriage bolts (1/4 x 5/8 inch) and 4 flange locknuts (1/4 inch) -
Page 7: Operation
g244666 g244327 Figure 13 Figure 14 1. Sunshade 3. Washer (5/16 inch) 2. Flange-head bolt (5/16 x 4. Clip nut (side-frame Assemble the switch panel to the 1-1/4 inches) channel) side-frame channels with the carriage bolts and locknuts (Figure 12) that you removed in step 3B. - Page 8 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.