Table of Contents
Advertisement
Do not operate the log splitter when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
Do not attempt to load a log until the log pusher has returned to the stop position.
8
stay alert and always pay attention to the movement of the machine and the work piece.
9
The log splitter must always be operated by one person only.
9
Keep hands away from the moving parts of the log splitter.
9
Keep hands away from splits and cracks which open in logs. They may close suddenly and crush or cut off parts of your hands.
9
Warning! ensure power is switched before attempting to clear jammed logs.
‰
For this reason Do not attempt to remove jammed logs by hand. A jammed log is a log which is only partially split and continues to
9
grip the splitting wedge. see section 5.3 for instruction on removing jammed logs.
1.6.
Safety of otHerS
Do not allow another person to help you with a jammed log.
8
Keep children and unauthorised persons away from the work area.
9
The log splitter must always be operated by one person only. other people must keep a safe distance from the log splitter especially
9
when it is in operation.
store the log splitter in a safe area away from children and other people not qualified to use the log splitter.
9
1.7.
general Safety
Do not make any modifications to the log splitter.
8
Do not leave the machine unattended when running.
8
Do not exceed the stated log capacity of the log splitter.
8
Do not use the log splitter for a task it is not designed to perform.
8
Do not leave the log splitter until the splitting wedge has returned to the start position.
8
Do not force the log splitter to work beyond its specified capacity.
8
ensure that there are no nails, screws or other foreign objects in logs to be split.
9
The end of logs should be cut square
9
logs should not be of an irregular shape.
9
Warning! The warnings, cautions and instructions referred to in this manual cannot cover all possible conditions and situations that
‰
may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be
applied by the operator.
2. introDuCtion
2.1.
lS370H.V2/ lS520H.V2
safe and easy way to split logs, offering continuous sizing and up to 4tonne ls370H.V2 and 5tonnes ls520H.V2 of pressure. splits
logs almost instantly upon contact, keeping labour and work time to a minimum. Features a two hand safety operation push-button
and lever. Fitted with a new Ce standard guard.
3. SpeCifiCation
model no: ...................................................................... lS370H.V2 .......................................................... lS520H.V2
Maximum load Pressure: ...................................................... 4tonne ..................................................................5tonne
Maximum log diameter: .................................................... Ø250mm .............................................................. Ø250mm
Maximum log length: ........................................................... 370mm .................................................................520mm
Minimum log diameter: ....................................................... Ø50mm ................................................................ Ø50mm
Minimum log length: ............................................................ 130mm .................................................................200mm
Motor Power: .............................................................. 1500W - 230V ...................................................... 2200W - 230V
overall Size (W x D x H): ...................................750 x 250 x 420mm ............................................. 940 x 270 x 510mm
4. aSSembly
4.1.
lifting HanDle (fig.1)
4.1.1.
Mount the lifting handle to the U bracket with two M6×16 bolts.
4.2.
log tray (fig.2)
4.2.1.
Mount the guard bottom plate to rear guiding plate and secure with two M6×12 socket head cap screws and locknuts. Loosen
the socket head cap screw and big washer on the wheel bracket, insert the open end of support strut 2 (fig2.2) between the big
washer and wheel bracket and tighten screw. Connect the upper end of support strut 2 (fig2.2) to the guard bottom plate with cross
recessed pan head screw M6×12 and locknut M6 and then tighten it.
fig.1
© Jack sealey limited
Original Language Version
fig.2
lS370H.V2 LS520H.V2 Issue 2 (3) 02/10/19
Advertisement
Table of Contents
