Sealey TC962.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instruction Wear eye
manual
protection
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
‰
equipment. Under Health and Safety Law, Employers and Self Employed Personnel have a legal duty to ensure Safe Working Conditions
for all employees and personnel that may come into contact with this equipment. In particular they must carry out a specific risk and
hazard assessment in the workplace to eliminate or reduce any risk found and must record, update and retain records of the results of
this inspection.
Familiarise yourself with the applications, limitations and any possible or potential hazards of the tyre changer.
9
Maintain the tyre changer in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
WARNING! Check regularly for damaged parts. Any part that is damaged must be repaired or replaced before the equipment is next
‰
used.
Locate the tyre changer in a suitable work area, keep area clean, tidy and free from unrelated materials. Ensure that there is adequate lighting.
9
WARNING! Use on a level surface, preferably concrete, to which the tyre changer must be bolted.
‰
Keep the tyre changer clean for best and safest performance.
9
Keep hands and feet well clear of the bead breaker.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip safety shoes.
9
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery and contain and/or tie back long hair.
9
Keep children and unauthorised persons away from the work area.
9
DO NOT use the tyre changer for any purpose other than that for which it is designed.
8
DO NOT operate the tyre changer if any parts are damaged or missing as this may cause failure and/or personal injury.
8
DO NOT allow untrained persons to operate the tyre changer.
8
DO NOT stand on the tyre changer.
8
DO NOT operate the tyre changer when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended maximum pressure 150psi (10.3 bar).
‰
WARNING! Disconnect the tyre changer from the air supply before changing accessories, servicing or performing any maintenance.
‰
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use, and ensure that all connections are secure.
9
DO NOT pull the hose from the air supply.
8
DO NOT direct air from the air hose at yourself or others.
8
When not in use ensure the air supply is turned off.
9
2. INTRODUCTION
i
Heavy steel construction. Pneumatic bead breaker. Suitable for use on most
automotive/light commercial open centred wheels. Features an additional air line coupling
tyre inflator / accessory. Supplied with standard tyre bar and PCL couplings.
To prevent damage to the rims of alloy wheels, it is essential to use a TC963 Tyre Bar.
3. SPECIFICATION
i
Model no. .................................................................... TC962
Working Pressure........................................................ 100psi
Maximum Pressure ..................................................... 150psi
Wheel Diameter (Minimum/Maximum) .............. 203 / 460mm
Wheel Depth (Minimum/Maximum) ..................... 40 / 300mm
Working Height .......................................................... 800mm
Tyre Bar for Aluminium Wheels (Optional) .................. TC963
4. AIR SUPPLY
4.1. Ensure the air valve (fig.5) is in the "off" position before connecting to the air supply.
4.2. Ensure an air pressure of between 100 and 150psi.
WARNING! Ensure that the air supply is clean and does not exceed150psi. Too high an air pressure and/or unclean air will cause
‰
excessive wear and may cause damage and/or personal injury.
4.3. Drain the air tank daily. Water in the air line will damage the tyre changer.
© Jack Sealey Limited
INSTRUCTIONS FOR
TYRE CHANGER - PNEUMATIC/MANUAL
OPERATION
TC962.V2
MODEL NO:
Wear ear Wear safety
protection footwear
Original Language Version
Warning: Wear protective
Crushing of hands gloves
fig.1
TC962.V2 ISSUE 1 26/03/18