Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for DeWalt DW720
Summary of Contents for DeWalt DW720
- Page 1 ® DW720...
- Page 2 10 11...
- Page 3 24 13 26 25 32 31 34 35 30...
- Page 4 62 61 64 61 55 62 64 55°-60° 10mm 1 - 3mm 74 72 73 71...
- Page 5 25mm 330 mm 330 mm 245 mm 225 mm 640 mm 25mm 380 mm 640 mm 245 mm 260 mm 380 mm...
- Page 6 43 42...
- Page 7 112 108...
- Page 8 E N G L I S H RADIAL ARM SAW DW720 Congratulations! EC-Declaration of conformity You have chosen a D WALT product. Years of experience, thorough product development and innovation make D WALT one of the most reliable partners for professional users.
- Page 9 E N G L I S H Safety instructions 17 Do not abuse cord When using Power Tools, always observe the safety regulations Never carry the tool by its cord or pull it to disconnect from the socket. applicable in your country to reduce the risk of fire, electric shock Keep the cord away from heat, oil and sharp edges.
- Page 10 • Take the time to thoroughly read and understand this manual prior to operation. Description (fig. A1 & A2) The DW720 Radial Arm Saw has been designed for the professional woodworking industry. This high precision machine can be easily and Never use a light socket.
- Page 11 E N G L I S H Also refer to the table below. Adjusting the table supports using the arbor (fig. A1 & D2) • Release the bevel clamp lever (19) and pull out the bevel latch (21) (fig. D2). •...
- Page 12 E N G L I S H Make sure that the ring (44) of the arbor nut (39) is against the - Upper guard (53) (fig. G1) and spring held rear guard (54) (fig. F2) for outer flange (fig. E1). full blade protection.
- Page 13 E N G L I S H • Loosen the two screws (73) and move the pointer (71) until the edge of • I = ON The tool now works in continuous operation. the out-rip pointer (74) lines up with the known width of the board on •...
- Page 14 E N G L I S H • Adjust the blade guard as described above and turn the dust extraction • Tilt the motor until the shaping head is in horizontal position. adaptor (55) away from your face (fig. F2). Remember that ripping •...
- Page 15 E N G L I S H Disc sanding (fig. N1) • Loosen the two wing nuts (108) in the front of the sabre saw to allow • Always use the downward (right-hand side) of the disc. the two angled retaining struts (109) to protrude from the rear (fig. R2). •...
- Page 16 E N G L I S H Legstand (fig. T) GUARANTEE The legstand (127) consists of four legs (128), four traverse rails (129) and four top traverse rails (130). The latter are the same size as the base frame • 30 DAY NO RISK SATISFACTION GUARANTEE • of your radial arm saw.
- Page 17 E N G L I S H QUICK REFERENCE CHART height adjustment crank mitre latch lever mitre clamp lever riplock yoke latch yoke clamp lever bevel latch bevel clamp lever en - 10...
- Page 18 Belgique et Luxembourg WALT Tel: 02 719 07 12 België en Luxemburg Weihoek 1, Nossegem Fax: 02 721 40 45 1930 Zaventem-Zuid Service fax: 02 719 08 10 Danmark WALT Tlf: 70 20 15 10 Hejrevang 26 B Fax: 48 14 13 99 3450 Allerød Deutschland WALT...