Table of Contents
Advertisement
--------------------------------------------------------HMCS47C,HMCS47CL
•
ELECTRICAL CHARACTERISTICS - 1 (Vee = 2.5 to 5.5V. Ta = -20 to +75°C)
Test Conditions
Value
Item
Symbol
min.
typo
max.
Input "Low" Voltage
VIL
-
-
0.15·Vee
Input "High" Voltage (1)
VIHl
0.S5·Vee
-
Vee
Input "High" Voltage (2)
VIH2
0.S5·Vee
-
10
Output "Low" Voltage
VOL
IOL
=
0.4 rnA
-
-
0.4
Output "High" Voltage
VOH
-IOH = O.OS rnA
Vee- O
.4
-
-
Interrupt Input Hold Time
tiNT
2'Tinst
-
-
Interrupt Input Fall Time
tfiNT
-
-
50
Interrupt Input Rise Time
trlNT
-
-
50
Output "High" Level
IOH
VOH = 10V
-
-
3
Current
Yin
=
Oto Vee
-
-
1.0
Input Leakage Current
IlL
Yin
=
0 to 10V
-
-
3
Pull up MOS Current
-Ip
Vee = 3V
10
-
SO
Vin=Vee. Vee=3V
(fosc/fcp = 200kHz)
Supply Current
Icc
Rf Oscillation,
External Clock
-
-
140
Operation
Vin=O to Vee
-
-
1
Standby I/O Leakage
ILS
HIT
Current
=0.5V
Vin=O to 10V
-
-
3
Yin -
Vee=2.5 to
-
-
6
Standby Supply Current
Ices
Vee
3.5V
RtT=
Vee=2.5 to
-
-
10
0.1 V
5.5V
External Clock Operation
----------
r-----
r----------
- - - -
t - - -
- 2 4 0 - -
External Clock Frequency
fcp
130
200
External Clock Duty
Duty
45
50
55
External Clock Rise Time
t rcp
0
-
0.2
External Clock Fall Time
tfcp
0
-
0.2
Instruction Cycle Time
TiNt
Tinst = 4/fcp
16.S
20
30.S
Internal Clock Operation (Rf Oscillation)
- - - - - - - - - - - - - - - - - - - - - - - - - - -
, - - - -
----
fOle
Rf = 200kil
± 2%
Clock Oscillation
Vee=2.5 to 3.5V
130
-
250
Frequency
fosc
Rf=2ookil
± 2%
130
350
Vee=2.5 to 5.5V
-
Tinst
Tlnst=4/f
OlC
16
-
30.S
Vee= 2.5 to 3.5V
Instruction Cycle Time
Tinst=4/fosc
Tinst
Vee=2.5 to 5.5V
11.4
-
30.S
[NOTE 11 All voltages are with respect to GND.
[NOTE 21 This is applied to RESET, HLT, OSC., INTo, INT. and the With Pull up MOS or CMOS type of I/O pins.
[NOTE 31 This is applied to the Open Drain type of I/O pins.
[NOTE 41 This is applied to the CMOS type of I/O or Output pins.
[NOTE 51 This is applied to the With Pull up MOS or CMOS type of I/O or Output pins
[NOTE 61 This is applied to the Open Drain type of I/O or Output pins.
[NOTE 71 I/O current is excluded.
[NOTE 81 The Standby I/O Laakage Current is the I/O leakage current in the Halt and Disable State.
[NOTE 91 I/O currant is excluded.
Unit
Note
V
V
2
V
3
V
V
4
Jls
JlS
JlS
JlA
6
2
JlA
r----
3
JlA
JlA
7
JlA
5,S
JlA
6,S
JlA
9
JlA
--- ---
kHz
%
Jls
Jls
JlS
r - -
r - - -
kHz
kHz
JlS
IlS
The Standby Supply Current is the supply current at VCC=2.5 to 5.5V in the Halt State. The supply current in tile case where the
supply voltage falls to the Halt Duration voltage is called the Halt Current (IDHI, and it is shown in "ELECTRICAL CHARACTERISTICS
-2."
113
Advertisement
Table of Contents
