Table of Contents
Advertisement
www.freeservicemanuals.info
When switching off, the same procedure is followed, but in
reverse order.
9.12.2 Implementation
To explain the operation of the line output stage, we use the
following start conditions:
•
C2433 is charged to max. 141 V (V
•
TS7421 is driven into conductivity.
5430
I Defl
141V
t1
6423
2425
7421
2421
2420
41V
6422
2426
Figure 9-19 Line deflection part 1
•
Period t1-t2: When TS7421 is driven into conductivity, the
capacitor voltage of 141 V will be divided across bridge-coil
L5422 and the deflection coil (connector 1417.) Due to the
chosen inductance values, there will be 100 V across the
deflection coil and 41 V across L5422. The linearly
increasing current in the deflection coil will result in a spot
moving from the center of the picture tube to the right. The
voltage across L5422 will also charge C2421 (41 V - 0.7 V.)
•
Period t2-t3: At the moment the LINEDRIVE signal
becomes high, TS7421 will stop conducting. A voltage will
be induced in the coils, trying to maintain the current. The
current through the line deflection coils continues to flow
through C2425 and C2421 and the current through L5422
continues to flow through C2426 and C2421. The energy
stored in the line deflection coil is passed to C2425, and the
energy of L5422 to C2426. The resonance-frequencies of
these two LC-circuits define the flyback time of the spot
from the right side of the picture tube to the left. On
average, no current flows through C2421 and thus the
voltage across this capacitor remains constant.
5430
I Defl
141V
6423
2425
7421
2421
2420
41V
2426
6422
Figure 9-20 Line deflection part 2
•
Period t3-t4: The same as period t2-t3; but now the current
flows in the opposite direction, since the voltage across
C2425 and C2426 is higher than the voltage across C2433
and C2421.
•
Period t4-t5: The coils try to maintain the negative current
and will negatively charge the capacitors. Because of this,
D6422 and D6423 will conduct. The voltage is 100 V
across the deflection coil and 41 V across L5422. Since
both diodes conduct, we may consider the voltage
constant. A linear current flows with the same changing
characteristics as in period t1-t2. The spot now moves from
the extreme left of the picture tube to the center. Before the
current becomes zero, and the spot is located in the center
of the frame, TS7421 reverts into conductivity. A short
negative current will flow. Then the cycle starts again.
Circuit Descriptions and Abbreviation List
)
BAT
5430
141V
t2
100V
Line defl.
6423
+
7421
2433
141V
-
2420
6422
41V
5422
5430
I Defl
141V
t3 t4
Line defl.
2425
6423
7421
2433
2420
6422
2426
5422
9.12.3 Corrections
Several corrections are necessary to obtain a proper picture.
Linearity Correction
A constant voltage across the horizontal deflection coil should
result in a linearly increasing saw-tooth current. This is not the
case however, as the resistance of the coil is not negligible. In
order to compensate for this, a re-magnetized coil L5421 in
series with the deflection coil is used. This coil ensures that
during time interval t1-t3 the circuit resistance will be higher
I
Defl
than during t4-t5.
L5421 is the linearity coil. To avoid self-oscillation, R3431 and
t2 t3
C2431 are placed parallel to L5421.
See diagram "Line deflection circuitry" item '*1.'
Line defl.
2425
2433
2421
S-correction
Since the sides of the picture are further away from the point of
2426
5422
deflection than the center, a linear saw-tooth current would
CL 96532156_024.eps
result in a non-linear image (the center would be scanned
060199
slower than the sides.)
To solve this, the deflection current for the right side and left
side is reduced.
C2433 is quadratically charged during time interval t1-t2. The
left and right voltage across the deflection coil decreases,
causing the deflection to slow down. In the center, the voltage
increases and the deflection will be faster.
An S-shaped current is superimposed on the saw-tooth
current. This correction is called 'finger-length correction' or 'S-
Correction.'
C2433 is relatively small, and as a result, the saw-tooth current
will generate a parabolic voltage with negative voltage peaks.
The current also results in a parabolic voltage across C2421,
resulting in the finger-length correction, proportionally
increasing with the picture width.
The EW-DRIVE signal will ensure the largest picture width in
the center of the frame. The largest correction is applied here.
The larger the picture width, the higher the deflection current
through C2433.
See diagram "Line deflection circuitry" item '*2.'
E/W-correction
A line written at the upper side or lower side of the screen will
be larger at the screen center when a fixed deflection current is
used. Therefore, the amplitude of the deflection current must
be increased when the spot approaches the screen center.
This is called East/West correction.
t4
t5
The EW drive signal originates in the HOP and is supplied to
Line defl.
100V
TS7480 via OpAmp 7450-B and optocoupler TS7482. The
+
2433
-
2421
141V
shape of this signal determines the various geometric
41V
41V
correction parameters:
5422
•
CL 96532156_025.eps
231299
•
•
•
•
•
TS7480 will charge capacitor C2421 more or less, increasing
the deflection current when reaching the center of the screen.
The moment TS7480 is driven into saturation, C2421 will
discharge during the flyback. As a consequence of this, C2421
must be charged again during the scan via the conduction
diode D6422 (as long as C2421 is not charged to the voltage
across L5422, D6422 will conduct.)
The current in the deflection coil is therefore larger than the
current flowing in L5422 (1-2.) The voltage across the
deflection coil increases, so the picture width increases. When
TS7480 blocks, C2421 will not discharge anymore, and the
voltage across C2421 will remain constant.
The result is that the voltage across the deflection coil is
minimal. The voltage across coil L5422, however, is maximal.
EM5A NTSC
H amplitude
EW-parabola
EW-corner
EW-trapezium
Horizontal parallelogram
Horizontal bow
9.
EN 131
Advertisement
Table of Contents
