Scantronic 9448+ Installation And Programming Manual
  1. Manuals
  2. Brands
  3. Scantronic Manuals
  4. Control Panel
  5. 9448+
  6. Installation and programming manual

Scantronic 9448+ Installation And Programming Manual

Hardwired control panel
Hide thumbs Also See for 9448+:
Table of Contents

Advertisement

Quick Links

See also: Installer and User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 9448+ and is the answer not in the manual?

Questions and answers

Related Manuals for Scantronic 9448+

Summary of Contents for Scantronic 9448+

  • Page 2: Table Of Contents

    Every effort has been made to ensure that the contents of this book are correct. However, neither the authors nor Scantronic accept any liability for loss or damage caused or alleged to be caused directly or indirectly by this book. The contents of this book are subject to change without notice.

  • Page 3: Introduction

    1. INTRODUCTION Operator Controls and Displays 496236 Issue 4...
  • Page 4 1. Introduction 496236 Issue 4...

  • Page 5: System Features

    1. Introduction Note: The 9427 shows zones and key captions not listed above. These functions are not available on the 9448+. System Features Detectors Full Setting Exit Times 496236 Issue 4...

  • Page 6: Part Setting

    1. Introduction Part Setting Entry and Unsetting the System Alarm 496236 Issue 4...

  • Page 7: Re-Arm

    1. Introduction 496236 Issue 4...

  • Page 8: Communicator Outputs

    1. Introduction Keypad Panic Alarm Chime Power Supply User Control 496236 Issue 4...

  • Page 9: Engineer Access

    1. Introduction Engineer Access Technical Description Specification 496236 Issue 4...

  • Page 10: Fuses

    Control Panel Main PCB Tamper switch Microcontroller Reset Pins NVM Chip Backlight Link Volume Control for Entry/Exit tones Battery Connector Comms Connector 21VAC Connector Connectors F3 - 21 VAC F1 - Battery F2 - 12V Aux Fuse Fuse Fuse 496236 Issue 4...

  • Page 11: System Planning

    2. System Planning 2. SYSTEM PLANNING Installation Precautions Locating The Control Panel Locating The External Bell Locating The Deterrent Bell (Dummy) Detectors 496236 Issue 4...

  • Page 12: Installation Example

    2. System Planning Installation Example Ground Floor First Floor 496236 Issue 4...

  • Page 13: Setting Options

    Setting Options 496236 Issue 4...

  • Page 14: Installation

    3. Installation 3. INSTALLATION Fitting the System Fitting the Control Panel Note: Do not drill the holes with the panel in position as this may result in damage to the electronics. Fitting a Remote 9427 Keypad 496236 Issue 4...

  • Page 15: Fitting Door Contacts

    3. Installation Fitting Door Contacts 496236 Issue 4...

  • Page 16: Fitting Pir Detectors

    3. Installation Fitting PIR Detectors Fitting The External Sounder 496236 Issue 4...

  • Page 17: Wiring The Control Panel

    3. Installation Wiring the Control Panel Cable Entries Mains Connection Battery Connection Connecting a 9427 Remote Keypad 496236 Issue 4...

  • Page 18: Backlighting

    3. Installation Note:The control panel, when supplied from the factory, is configured with its backlight ON. To turn the backlight OFF clip the link indicated in Figure 3. 496236 Issue 4...

  • Page 19: Detector Circuit Connections

    3. Installation Detector Circuit Connections Connecting Door Contacts 496236 Issue 4...

  • Page 20: Connecting Pirs

    3. Installation Connecting PIRs 496236 Issue 4...

  • Page 21: Connecting A Communicator

    3. Installation Connecting a Communicator 496236 Issue 4...

  • Page 22: Connecting Sounders And Strobe

    3. Installation Connecting Sounders and Strobe 496236 Issue 4...

  • Page 23: Wiring Example

    3. Installation Wiring Example 496236 Issue 4...

  • Page 24: Initial Start Up

    Initial Start Up Note: The SAB module in the external sounder will continue to ring until the hold off supply is connected, or until the bell cover lid tamper switch is closed. 496236 Issue 4...

  • Page 25: Programming

    4. Programming 4. PROGRAMMING Factory Default Programming Changing Default Programming 496236 Issue 4...

  • Page 26: Engineer Program Command List

    4. Programming Engineer Program Command List ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER...

  • Page 27: To Re-Enter Programming Mode

    4. Programming ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER Does not change access codes ENTER Notes: 1. n..n = the numbers of the zones. Key the zone number to toggle the zones on or off.

  • Page 28: Restoring Factory Defaults

    Restoring Factory Defaults Engineer Walk Test 496236 Issue 4...

  • Page 29: Programming Example

    Programming Example 496236 Issue 4...
  • Page 30 Manufactured in the UK by Scantronic Ltd. Product Support (UK) - Tel - (0891) 616343 between 09:00 and 17:30, Monday to Friday. (CALLS CHARGED AT 50P PER MINUTE.) PRODUCT SUPPORT FAX NO. (01594) 544136. Part No. 496236 Issue 4...

This manual is also suitable for:

Dwd5410w

Table of Contents

Save PDF