Sealey PH10.V5 Instructions Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear
instruction protective
manual footwear
1. CONTENTS
section 2. General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.
section 2.1. Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.
section 2.2. technical Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.
section 3. safety / operational Instructions. . . . . . . . . . . . . . . . . .2.
section 4. Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.
section 5. operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.
section 6. Maintenance/ Examination/ Inspection. . . . . . . . . . . . .3.
section 7. owner's & operator's responsibilities . . . . . . . . . . . . .3.
section 8. Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . .4.
section 9. Parts List/ Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 5 & 6.
2. GENERAL
2.1 Identification
supplier: sealey Power Products,
Kempson Way,
suffolk Business Park,
Bury st Edmunds,
suffolk, IP32 7Ar.
Model no: PH10.V5
2.2 Technical Data
Rated Capacity
safe Working Load (sWL) 1tonne (tested to 50% overload).
Lifting cap. in Position 1: . . . . . . . . . . . . . . 1000kg
Lifting cap. in Position 2: . . . . . . . . . . . . . . 750kg
Lifting cap. in Position 3: . . . . . . . . . . . . . . 500kg
Lifting cap. in Position 4: . . . . . . . . . . . . . . 250kg
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76kg
a) Design capability: test Load 50% overload.
b) for a description of in-service and out-of-service conditions see
section 3 safety, section 6 Maintenance and section 7.
c) the crane is fitted with a bypass valve that will prevent the ram
from over extending.
d) for applications see section 3 safety.
e) for control system, see fig.1 for release valve and pump handle
assy. usage is explained in section 5 operation.
f) for ground condition requirements, see section 3 safety.
g) for information on parts and materials requiring specialised
repair techniques see section 6 Maintenance.
© Jack sealey Limited
InstructIons for:
1 TONNE LOW PROFILE ENGINE CRANE
MoDEL no: PH10.V5
Wear
protective
gloves
Page No.
Original Language Version
fig.1
Page 1
Fig.1
PH10.V5 Issue: 1 - 02/03/16