Advertisement
Installation Guide
Assembling the headboard bracket (optional)
IMPORTANT!
•
Failure to follow the installation steps as they appear in this guide could result in damage to your adjustable
bed.
•
For safety reasons, lifting of the adjustable bed must always be performed by two (2) people; and the unit
should always be on a flat surface.
•
Make
sure
to
3 inches (76.2 mm) between the headboard and the top of the mattress.
1
Using the remote control, raise the head section of the adjustable
bed to its full height.
2
Locate the first round panel under the head section of the bed.
The second round panel is for the bed leg.
3
Position the inner headboard bracket underneath the first round
panel. The bracket opening should be facedown under the bar.
4
Insert a retainer bolt fitted with a washer into the slot under the
inner headboard bracket and through the round panel. Tighten
the bolt using the Allen key wrench.
5
Place the open side of the outer headboard bracket onto the
exposed square tube of the inner headboard bracket to create
a tight fit.
6
Insert a retainer bolt fitted with a washer through the outer
headboard bracket and into the inner headboard bracket.
Tighten the bolt with an Allen key wrench. Leave loose enough
for adjusting.
7
Repeat steps 2 to 6 to install the brackets on the other side of the
head section of the adjustable bed.
8
When the headboard brackets are assembled, make sure there is
a space of 1.5 inches (38.1 mm) to 2 inches (50.8 mm) between the
edge of the adjustable bed and the headboard brackets.
9
Securely fasten the headboard bolts (not included with your parts
box) to the end of the headboard bracket assembly.
10
If you need to adjust the headboard brackets, unscrew the
bolts holding the outer headboard bracket and move them the
necessary distance. Reinstall the bolts and tighten securely.
Place your mattress on the adjustable bed surface.
Your adjustable bed and headboard installation is now complete.
position
the
bottom
of
the
headboard
cross
member
no
more
than
9
Hide quick links:
Advertisement
Need help?
Do you have a question about the 900 POWER BASE and is the answer not in the manual?
Questions and answers
The remote doesn’t operate one side of adjustable. How do I check to make sure remote is paired properly. Pairing the trmote to my side of bed remote
The context does not provide specific instructions on checking if the remote is paired properly to your side of the bed. However, it mentions ensuring that the remote control is paired with the adjustable bed if it fails to respond.
This answer is automatically generated
@Mr. Anderson
@Mr. Anderson So how do I reconnect the remote to Bed frame
Can not get remote to work.
To fix the remote for the MATTRESS FIRM 900 POWER BASE if it is not working, try the following steps:
1. Pair the Remote – Ensure the remote control is paired with the adjustable bed.
2. Check Power – Make sure the adjustable bed is plugged into a working and grounded electrical outlet.
3. Disconnect App Connection – The remote will not work while the bed is connected to the Mattress Firm 900 mobile app. Disconnect from the app if necessary.
4. Reset the Bed – Press and hold the FLAT button on the remote for over 1.5 seconds after plugging in the power cord to reset the bed.
5. Replace Batteries – If the remote has batteries, replace them with new ones.
If the issue persists, refer to the troubleshooting section in the manual for further guidance.
This answer is automatically generated
Foot of bed stuck
The manual does not provide specific troubleshooting steps for a stuck foot mechanism. However, you can try the following general steps:
1. Check for Excess Weight – Ensure that the bed is not overloaded beyond the recommended weight limit (850 lbs. distributed evenly).
2. Reset the Control Unit – If the bed has automatically stopped due to excess weight, remove the weight and wait 30 seconds for it to resume function.
3. Inspect for Damage – If the bed has been dropped or damaged, the foot mechanism may not function properly.
4. Check Electrical Connections – Ensure the foot lift cord is properly plugged into the control box.
5. Unplug and Restart – Disconnect the bed from power, wait a few minutes, and plug it back in.
6. Contact Support – If the issue persists, consult the manual for troubleshooting or contact the manufacturer for further assistance.
If the foot mechanism is physically stuck, avoid forcing it and seek professional help.
This answer is automatically generated
How I disassemble the Mattress Firm 900 adjustable bed?
Our dog chewed through the wires so our bed no longer works. How can we order new wires and parts to make it work again?