WANHAO DUPLICATOR 7 Getting Started

PREPARE DUPLICATOR 7 FOR PRINTING
7
Place vat on top of the LCD screen and tighten both
Z brackets. If you over-tighten it too much the LCD
screen will go temporarily white. The vat
should not be able to be lifted at all.
9 Tighten the central knob and loosen the four
screws at the sides so the platform can move freely
up and down.
NOTE: ensure the two side knobs are completely free when
lowering the platform to avoid damage to the screen.
Now click on the "Control" tab. Press the "Home" button to lower the
11
platform onto the screen. The platform will move down to be set on the
screen (level 0 in Z axis.) and stop.
Press down on the middle of the Steel platform with one hand and tighten 4 screws
12
at the side. All 4 screws should now be tight. You can check that you have homed the platform correctly by 11.visual checking
there's no space between the LCD screen and the build platform. Now turn the screen off before fill the vat with resin. Prints
don't consume a lot of resin, a quarter full vat is enough for a medium sized print.
a. b.
NOTE: Don't push the build platform too hard
to avoid breaking the LCD screen. Make sure the
platform touching the screen is sufficient.
Place the hood back onto the printer. In "Control" panel press +10 button to lift the platform. Once resin is
13
under the platform, move the platform back to home by clicking the -1 step button 10 times, leave a few seconds
between clicks to enable the resin to move out from under the platform.
Z Axi S
Z Axi S
NOTE: wait 30sec betwen b and c, to enable resin to move
under the platform. If you miscount it is safer to press an
addi tional step, the platform will not move further when
correctly located.
Side the platform onto the platform arm.
8
10
Place the hood back onto the printer
c.
NOTE:once started, the print can't be paused and refilled
so it's safer to over-fill and reuse the resin.
Switch on the screen at the front of the machine.
14
Now you are ready to print, press "play". Once the
print ,press "play".Once the print has finished,the
machine will show "print 100% complete"and will
stop.
NOTE: Don't remove the hood during
the print or the print will stop.
WANHAO DUPLICATOR 7
GETTING STARTED GUIDE
1 DOWNLOAD AND INSTALL SOFTWARE
Go to www.wanhao3dprinter.com and download "Creation
Workshop" and "D7driver_1" located at "Download software—
Duplicator 7". The latest version is always online.
-Install the driver "D7driver_1" on your computer.
-Execute the Creation Workshop software by clicking on
"CreationWorkshop.exe"
2 UNPACK AND CONNECT CABLES
With the printer switched off, connect:
A.VGA or HDMI cable supplied to the computer and 3D printer.
B.USB cable supplied to the computer and 3D printer.
C.Power cable to the power supply.
CONNECT SOFTWARE AND PRINTER
5
In Creation Workshop, click on "Con-figure", and then open the subfolder
"Configure Machine". In the configu-ration folder connect the printer to
the computer by clicking on the button"Configure". Select the port you
have connected the USB to and set the speed to 115200 and data bits to
8. Press "OK" and finally press "Apply Changes". To connect your computer
and the the duplicator 7 . .
TIP: If you experience any issue configuring the screen resolution or usb port, visit
our video tutorial section at www.wanhao3dprinter.com "video".
6 SELECT RESIN AND SLICE OBJECT
Once the object is loaded and located in the build area check the settings
of the printing profile. Go to the "Configure" screen and open the "Configure
Slicing Profile" tab. Select the printing profile from the "Machine Profiles"
list that matches your resin and desired re-solution.
Now click "3D View" and check that the object is correctly placed inside the
printing area. Press the slice button to start the
A confirmation window will appear.
Now open "Slice View" to check that the first layer of every object is in con-
tact with the platform.
Note: Click here to see the slice view
on the 3D printer screen. Do not
select while a vat with resin is in the
printer or it will cure the resin.
3 CONFIGURE SCREEN RESOLUTION
Go to your computer desktop, right click and open
"Screen resolution". Set your screens to "Multiple
Displays" and "extend this display mode", keeping
your monitor as the main screen. Video instructions
available at www.wanhao3dprinter.com "Video-
D7".
SWITCH ON PRINTER
4
Switch on your computer and the switch at front
of printer. Open the software and load the object
(STL,OBJ or AMF)
slicing operation.