ABB SM500F Commissioning Instructions

ABB SM500F Commissioning Instructions

Field-mountable paperless recorder
Hide thumbs Also See for SM500F:

Advertisement

A B B M E A S U R E M E N T & A N A LY T I C S | C O M M I S S I O N I N G I N S T R U C T I O N | C I/S M 5 0 0 F - E N R E V. A
SM500F
Field-mountable paperless recorder
Introduction
SM500F
field-mountable
This publication provides the following
paperless recorder
commissioning instructions for the SM500F field-
mountable paperless recorder:
1
2
3
4
5
6
7
Location
location requirements
Mounting
installation requirements to achieve
IP66/NEMA 4X hose-down rating
Electrical connections
AC and DC min./max. values and
fuse requirements
Navigation
navigating the user-interface quickly
and effectively
Menus overview
menu familiarization
Basic setup
steps required for first-time use
Symbols and icons
a schedule of icons/warning symbols that
may be displayed during operation
Innovative, simple, reliable
recording
Measurement made easy
For more information
Further publications are available for free download
from:
www.abb.com/measurement
or by scanning this code:
Instruction Manual
SM500F
Field-mountable paperless recorder
Data Sheet
SM500F
Field-mountable paperless recorder
Search for or click on
IM/SM500F-EN
DS/SM500F-EN

Advertisement

Table of Contents
loading

Summary of Contents for ABB SM500F

  • Page 1 For more information — SM500F field-mountable This publication provides the following Further publications are available for free download paperless recorder commissioning instructions for the SM500F field- from: mountable paperless recorder: www.abb.com/measurement Location or by scanning this code: location requirements Mounting...
  • Page 2: Health And Safety

    Data Sheets (where applicable) can be obtained from the enclosure or remove the barrier. the Company, together with servicing and spares information. Recycle separately from general waste under the WEEE directive. CI/SM500F–EN Rev. A...
  • Page 3: Specification

    Storage temperature range instruments do not fall within the scope of the RoHS –20 to 70 °C (–4 to 174 °F) Directive, however ABB has taken the decision to adopt the recommendations in the Directive as the Enclosure sealing target for all future product design and component IP66 and NEMA4X (the enclosure meets the requirements of purchasing.
  • Page 4 B – Within humidity limits Sensors IP66 / NEMA 4X A – Close to sensors C – Environmental protection standards B – Eye-level location D – Use screened cable C – Avoid vibration Fig. 2 Environmental requirements Fig. 1 Siting CI/SM500F–EN Rev. A...
  • Page 5 IP66/NEMA 4X hosedown rating. Dimensions in mm (in.) Fig. 4 Wall-mounting +1.0 –0.0 +0.04 (5.43 Panel cut-out –0.0 +1.0 –0.0 +0.04 (5.43 (1.2) (1.2) –0.0 Left-hand bracket only shown. Right-hand bracket omitted for clarity Fig. 3 Panel-mounting CI/SM500F–EN Rev. A...
  • Page 6 D. Ensure the plastic washers remain in the positions fitted. 4. Secure the recorder to the pipe using the remaining clamp plate, spring lock washers and nuts E. Vertical pipe Horizontal pipe Fig. 5 Pipe-mounting CI/SM500F–EN Rev. A...
  • Page 7: Electrical Connections

    – If the recorder is used in a manner not specified by the Company, the protection provided by the equipment may be impaired. – All equipment connected to the recorder's terminals must comply with local safety standards (IEC 60950, EN601010-1). CI/SM500F–EN Rev. A...
  • Page 8 B and C, the cable is routed between their terminal blocks as shown. 5. Connect cable screens only to terminals E. Fig. 6 Cable knockouts, ethernet cable routing and cable screening connections CI/SM500F–EN Rev. A...
  • Page 9 (BZX79 – B/C2V4) to the input as shown. Fig. 7 Electrical connections IMPORTANT (NOTE) Tighten power supply terminal screws to a torque of 0.8 Nm (7 lbf.in). Tighten all other terminal screws to a torque of 0.5 Nm (4.5 lbf.in). CI/SM500F–EN Rev. A...
  • Page 10 (volt-free or 24 V) Analog input Fig. 9 Dual analog / digital input connections Fig. 11 Power supply connections IMPORTANT (NOTE) Tighten all analog / digital input terminal screws to a torque of 0.5 Nm (4.5 lbf.in). CI/SM500F–EN Rev. A...
  • Page 11 Chart, Indicator, Audit Log, Alarm Log or Totalizer Log view to the SD card if is pressed when an operator menu is not displayed. F Door release. G Door lock (optional). Table 1 Operator keys and door features CI/SM500F–EN Rev. A...
  • Page 12: Menus Overview

    4. Select the configuration entry mode: a. Edit Current Configuration b. Open a Configuration c. New Configuration CI/SM500F–EN Rev. A...
  • Page 13 Totalizer / statistics Log enable Bar graph display Alarm Trip Points Menu enables Archive Archive file format Archive file enables Wrap Batch Enable Batch Recording (If option enabled) Start/Stop, Abort Operator Login Batch Number Field 1(to 3) Title CI/SM500F–EN Rev. A...
  • Page 14 Modbus TCP Port Reverse IEEE data Implementation – Connections Allowed Client (Master) Modbus TCP Port Poll Rate (ms) Poll fail limit Response Timeout (ms) Comms analog I/P Comms analog I/P Protocol Comms digital I/P Comms digital I/P Protocol CI/SM500F–EN Rev. A...
  • Page 15: Basic Setup

    Group 1 and press the key to for the first time. For detailed configuration instructions refer to display the group's Recording tab. the User guide – IM/SM500F-EN. 2. Use the keys to highlight the edit button ( ) next...
  • Page 16: Symbols And Icons

    SD card slot Delayed low process alarm High latch alarm Low latch alarm Fast rate alarm Slow rate alarm High annunciate alarm Low annunciate alarm Real-time alarm Alarm acknowledged Operator message Daylight saving start / end changed Electronic signature CI/SM500F–EN Rev. A...
  • Page 17 Power failed Power restored Calibration change Configuration change File deleted Archive media inserted Archive media removed Archive media offline Archive media online Archive media full System error / reset archiving Daylight saving start / end changed FTP Logon CI/SM500F–EN Rev. A...
  • Page 18 Notes CI/SM500F–EN Rev. A...
  • Page 19 Sales Service Software CI/SM500F-EN Rev. A...
  • Page 20 We reserve the right to make technical changes or modify the contents of this document without prior notice. With regard to purchase orders, the agreed particulars shall prevail. ABB does not accept any responsibility whatsoever for potential errors or possible lack of information in this document.

Table of Contents