Symbols; Sizing - ABB ACS800-U4 Hardware Manual

ACS800-04 size Nominal
ratings
I
cont.max
A
Three-phase supply voltage 525 V, 550 V, 575 V, 600 V, 660 V or 690 V
-0011-7 13
-0016-7 17
-0020-7 22
-0025-7 25
-0030-7 33
-0040-7 36
-0050-7 51
-0060-7 57
-0070-7 79
-0100-7 93
-0120-7 113
-0145-7 134
-0175-7 166
-0205-7 190

Symbols

Nominal ratings
I
cont.max
I
max
Typical ratings:
No-overload use
P
cont.max
Light-overload use (10% overload capability)
I
2N
P
N
Heavy-duty use (50% overload capability)
I
2hd
P
hd

Sizing

The current ratings are the same regardless of the supply voltage within one voltage range. To achieve
the rated motor power given in the table, the rated current of the drive must be higher than or equal to
the rated motor current.
Note 1: The maximum allowed motor shaft power is limited to 1.5 · P
value is greatest). If the limit is exceeded, motor torque and current are automatically restricted. The
function protects the input bridge of the drive against overload. If the condition exists for 5 minutes, the
limit is set to P
Note 2: The ratings apply in ambient temperature of 40°C (104°F). In lower temperatures the ratings
are higher (except I
Note 3: Use the DriveSize PC tool for a more accurate dimensioning if the ambient temperature is
below 40°C (104°F) or the drive is loaded cyclically.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
No-overload Light-overload
use use
I
P
max cont.max
kW
A
14 11 11.5
19 15 15
28 18.5 20
38 22 23
44 30 30
54 30 34
68 45 46
84 55 52
104 75 73
124 90 86
172 110 108
190 132 125
245 160 155
245 160 180
continuous rms output current. No overload capability at 40 °C.
maximum output current. Available for 10 s at start, otherwise as long as allowed by drive
temperature.
typical motor power. The power ratings apply to most IEC 34 motors at the nominal voltage,
230 V, 400 V, 500 V or 690 V.
continuous rms current. 10% overload is allowed for one minute every 5 minutes.
typical motor power. The power ratings apply to most IEC 34 motors at the nominal voltage,
230 V, 400 V, 500 V or 690 V.
continuous rms current. 50% overload is allowed for one minute every 5 minutes.
typical motor power. The power ratings apply to most IEC 34 motors at the nominal voltage,
230 V, 400 V, 500 V or 690 V.
.
cont.max
).
max
Heavy-duty use
I P I
2N N 2hd
A kW A
7.5 8.5
11 11
15 15
18.5 19
22 22
30 27
37 34
45 42
55 54
75 62
90 86
110 95
132 131
160 147
Frame Air
size flow
P
hd
3
kW m /h
5.5 R4 103
7.5 R4 103
11 R4 103
15 R4 103
18.5 R4 103
22 R4 103
30 R5 250
37 R5 250
45 R6 405
55 R6 405
75 R6 405
90 R6 405
110 R6 405
132 R6 405
PDM code: 00096931-J
, 1.1 · P or P
hd N cont.max
Technical data
93
Heat
dissipation
W
300
340
440
530
610
690
840
1010
1220
1650
1960
2660
3470
4180
(whichever