Sealey PI1000.V3 Instructions

thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Warning:
refer to
explosive
instruction
risk
manual
1. Safety
▲ danGer! - Beware, lead-acid batteries generate explosive gases during normal battery operation.
Wash immediately with soap and water if battery acid contacts skin or clothing. if acid enters eye, flush immediately with cool
9
clean running water for at least 15 minutes and seek immediate medical attention
do not smoke or allow a spark or flame in the vicinity of the battery or engine.
8
if the battery terminals are corroded or dirty, clean them before attaching the clips.
9
warninG! to prevent the risk of sparking, short circuit and possible explosion do not drop metal tools in the battery area,
‰
or allow them to touch the battery terminals.
Before attaching to battery, remove personal metallic items such as rings, bracelets, necklaces and watches. A lead acid
9
battery can produce a short-circuit current which is high enough to weld such items to the vehicle and cause severe burns.
Keep children and unauthorised persons away from the working area.
9
warninG! do not use on any vehicles other than those with 12Volt dc systems.
‰
warninG! for delicate items such as laptops, an anti-surge device is recommended.
‰
do not connect to any Ac power source.
8
do not connect to any Ac power source.
8
do not get inverter wet or use in damp or wet locations or areas where there is condensation.
8
do not use the inverter for any purpose other than for which it is designed.
8
do not pull the cables or clips from the battery terminals.
8
do not operate the inverter if damaged.
8
do not connect to a positive earthed system. ensure you have the polarity correct before connecting, red clip to positive (+)
8
battery terminal and black clip to negative (-) battery terminal.
Before connecting ensure nothing is plugged into the inverter, and the inverter is switched off.
9
warninG! inverters become hot during use.
‰
When not in use store inverter in a safe, dry, childproof location.
9
2. introdUction
supplies continuous smooth 230V power from 12V dc power supply found in cars, caravans, boats and HGVs. suitable for powering small tVs,
laptops, power tools and various other electrical equipment within the wattage rating of the inverter. features usB port for use on various domestic
electrical equipment such as digital cameras and mobile phones. Anodized aluminium case provides durability and maximum heat dissipation.
safety features include automatic overload shut-down and a low battery alarm to prevent damage to the supply battery. supplied with battery leads
3. SpecificationS
model no. .............................................................. Pi1000.V3
input Voltage ..............................................................12V dc
output Voltage ......................................................... 230V Ac
continuous output ......................................................1000W
maximum output .........................................................2000W
output frequency ..........................................................50Hz
dimensions (WxdxH) ....................................280x215x72mm
supply connections ...........................Battery terminal leads
4. SetUp & operation
4.1. power Source requirements.
4.1.1. the inverter must be connected to a 12V dc negative earth system. do not use with a positive earth system.
4.1.2. the power source must be capable of providing between 10.0V and 15.5V and able to supply the necessary current
to operate the load.
4.2. connecting Battery Leads to inverter.
4.2.1. to attach the Battery leads remove the terminal caps from the rear of the inverter (fig.1).
4.2.2. Place the Black lead eyelet connector over the Black/negative terminal post on the inverter, replace and tighten the terminal cap.
4.2.3. Place the red lead eyelet connector over the red/Positive terminal post on the inverter, replace and tighten the terminal cap.
© Jack sealey limited
instructions for
power inverter 1000w 12v dc-230v 50hz
model no:
Wear eye Wear
Protection Protective
Gloves
Original Language Version
pi1000.v3
Warning:
electricity
.
Pi1000.V3 | issue 1 19/04/16