Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for YUNEEC Breeze 4k
Summary of Contents for YUNEEC Breeze 4k
- Page 2 INTRODUC TION Breeze is a flying camera that is designed to take aerial photos and videos of you. It is small, easy to fly both indoors and outdoors, and is controlled by your smart phone or tablet computer. The application (Breeze Cam) features five custom automatic flight modes that make positioning Breeze very easy.
- Page 3 SPECIFICATIONS Aircraft Dimensions (without propeller protectors): 196x196x65 mm Dimensions (with propeller protectors): 327x327x65 mm Diagonal Wheelbase: 240mm Takeoff Weight: 385g Propeller Protector: Quick-Release Propeller Protector. Battery: 3-Cell 11.1V 1150mAh 12.715Wh Li-Po Battery Motor：2206 Brushless Outrunner Motor Maximum Flight Altitude: 80m (Limited by Software) Flight Time：Up to 12 mins Max Horizontal Speed: 5m/s (Limited by Software) Max Ascending Speed: 1m/s...
- Page 4 Charger Model: BC24803015 Output: 12.6V DC,1.5A PREPARATIONS 1. CHARGING THE BATTERY (~45min) charger LED codes Standby Charging Abnormal Charging Balance Charging Fully Charged Battery Warnings: To charge the flight battery, you must use only the included charger. Do not over-discharge the LiPo battery. If at any time the LiPo battery begins to balloon or swell,discontinue charging or discharging immediately.
- Page 5 NOTICE: FAMILIARIZE YOURSELF WITH EACH TASK MODE BY READING THE TUTORIALS ON THE BREEZE CAM APP BEFORE OPERATING BREEZE. 3. UNFOLDING THE LANDING GEAR Unfold the four landing gears as shown in the below illustration. 4. INSTALLING THE PROPELLER PROTECTORS Install the four propeller protectors to the correspond- ing positions as shown in the illustration below.
- Page 6 5. REMOVING THE LENS COVER 6. INSTALLING THE FLIGHT BATTERY Slide in the fully charged battery until it locks. Remove the battery by pressing the locking tab and sliding the battery to the rear of Breeze . 7. POWERING ON/OFF BREEZE POWER ON: To start your Breeze , press and hold the power button at the rear of Breeze.
- Page 7 POWER OFF: Press and hold the power button until the LED glows solid red. After successfully switching off, it will emit a “power off” sound after letting go of the power button. 8. BINDING BREEZE WITH YOUR SMART DEVICE Power on your Breeze on a flat and stable surface and wait for it to complete initialization.
- Page 8 Nor th 1.5m ( 5ft ) Tap [ ] and select Drone Settings, and then swipe the screen to “Compass Calibration”. Follow the on-screen animations to complete the calibration. The LED indicator blinks white or yellow during the whole compass calibration process, when you complete the process, the LED will blink green and Breeze will emit an audible sound.
- Page 9 12. UNDERSTANDING THE FLIGHT MODES Tap the [ ] icon to enter the TASK page and there TAS KS are five flight modes for you to select with: 100% SELFIE ORBIT JOURNEY FOLLOW PILOT Before GPS is ready,only Pilot mode can be used. 13.
- Page 10 The Flight Log is designed to record your total flights, including flight time, flight date and flight location. You may email the flight log info to Yuneec Customer Support when needed. NOTICE AND WARNINGS SAFETY PRECAUTIONS Breeze may drift or fail to position when it flies...
- Page 11 GENERAL WARNINGS 1. Breeze is not suitable for children under 14 years of age. 2. Breeze is designed for leisure purposes. The pilot must always maintain direct visual contact with Breeze and monitor its trajectory. Breeze must be used in accordance with the civil aviation regulations in your country.
- Page 12 DISCLAIMER Yuneec Electric Aviation cannot be held liable for any damage, injury or for use of the product in violation with legal regulations, especially in the following circumstances: Damage and / or injury as well violation of legal regulations resulting from a failure to comply with the operating instructions or the instructions at www.yuneec.com, product information, user manual...
- Page 13 Further losses which do not fall within the scope of use defined by Yuneec Electric Aviation as improper. This product is designed for both professional use and personal, private use. The national and international laws and regulations in force as the time of taking off must be adhered to.
- Page 14 FCC STATEMENT This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
- Page 15 IC RADIATION EXPOSURE STATEMENT FOR CANADA This device complies with Industry Canada licence-ex- empt RSS standard(s).Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
- Page 16 We may also collect personal information used in registration if you choose to become a registered user and any other information user provided to Yuneec. We may also collect information which user send to other users, and the recipients and senders of such information.
- Page 17 CUSTOMER SERVICE Manufacturer Yuneec International (China) Co., Ltd. Production Address: East Zhengwei Road No.388, Jinxi Town, Kunshan City, Jiangsu Province Distributor US: Yuneec USA Inc. Address: 5555 Ontario Mills Parkway, Ontario, CA91764, USA Tel: +1 855 284 8888 EU: Yuneec Europe GmbH Address: Niklaus–Otto-Strasse 4,...
Need help?
Do you have a question about the Breeze 4k and is the answer not in the manual?
Questions and answers