Related Manuals for Wellis MONT BLANC
Summary of Contents for Wellis MONT BLANC
- Page 1 USER MANUAL MONT BLANC SPA SYSTEM - 3x3HP Hydromassage pumps - Energy-efficient LAING circulation pump - 71 jets - Hot air blower pump - UV-C water sanitizer - WPC frame Version: 01.2014 www.wellis.eu...
- Page 2 Standard Specification Dimensions: 2180 x 2180 x 910 mm Shell material: PU reinforced acrylic 6,3mm Sitting places: 5 persons Reclining places: 1 person Water volume: 1300 l Net weight: 320 kg Power requirement: 3 x 16A (400V) optimum 1 x 32A (230V) minimum Total number of jets: 71 pc Hydromassage pump:...
- Page 3 5 year on spa shell: Wellis warrants the structure of the Pool Shell against defects in workmanship and material for a period of 5 years, subject to the limitations and conditions listed in this Warranty.
- Page 4 1 year on Wellis Spa Umbrella: The factory installed Wellis Spa Umbrellas are warranted against failure due to defects in materials or workmanship for one year from the original date of delivery.
- Page 5 Wellis Magyarország Kft. shall not be liable for any incidental or consequential damages for breach of any expressed or implied warranty, breach of contract, negligence, strict liability, or any other legal theory related to this product.
- Page 6 It is obligatory to observe all information, details and requirements which are in the product`s installation diagram regarding elelectricity demand and drain installation. These information can be found in the user manual, or able to download from www.wellis.eu. If you didn`t get the document from your dealer, please contact export@wellis.eu.
- Page 7 12 months, for the purpose of assessing Wellis Magyarország Kft. liability, all aspects covered by this Warranty will be treated on a pro-rata basis. Wellis Magyarország Kft. or its agents will not be liable for any incidental or consequential loss or injury. Nor will Wellis Magyarország Kft.be liable for costs associated with but not limited to building alterations or finishes and under no circumstances will be liable for greater expense than the amount paid for the product.
- Page 8 SERVICE-WORK The announcement date of damage: _____________________________ Date of received goods/parts for repair: _____________________________ Date of the return of repaired goods/parts: ____________________________ Date of site service: _____________________________ STAMP Improved error: _____________________________ Mode of repair: _____________________________ Failed component: _____________________________ New deadline for the warranty: __________________________ The announcement date of damage: _____________________________...
- Page 13 3.Clean with high pressure nozzle to remove all debris clinging to the filter. 4.Soak filter in warm water and Wellis Alga-Sokk to remove all body oils and grime. Never use chlorine to clean the filter! If you use textile filter, you can wash it...
- Page 14 The chemical equilibrium of the water The water of the whirlpool will be clean and clear if its chemical components are in equilibrium. 1. pH-values: The first important indicator is the pH value of the water. pH is measured in a scale between 0-14 where 7 is the neutral value.
- Page 15 TROUBLESHOOTING...
- Page 17 Mont Blanc Spa system BALBOA TP800 HOT TUB Control panel Main screen SPA STATUS Important information about spa operation can be seen quickly from the Main Screen. The most important features, including Set Temperature adjustment, can be accessed from this screen.
-
Page 18: Press And Hold
NAVIGATION Navigating the entire menu structure is done with the 5 buttons on the control panel. When a text item changes to white during navigation, that indicates the item is selected for action. Operating or changing a selected item is generally done with the center or “Select” button. The only item that can be changed on the left side of the Main Screen is the Set Temperature. - Page 19 If the Spa has a Circ Pump, a Circ Pump Icon will appear to indicate its activity, but outside of Priming Mode, the Circ Pump cannot be controlled directly. NOTE: The icon for the pump that is associated with the heater (Circ or P1 Low) will have a red glow in the center when the heater is running.
-
Page 20: Dual Temperature Ranges (High Vs. Low)
PRESS-AND-HOLD If an Up or Down button is pressed and held when an item in a Menu List is highlighted, the list can be scrolled quickly from top to bottom. The scroll bar on the right side of the screen indicates the relative position of the highlighted item in the list. -
Page 21: Ready-In-Rest Mode
READY-IN-REST MODE READY/REST appears in the display if the spa is in Rest Mode and the Jets 1 Button is pressed. It is assumed that the spa is being used and will heat to set temperature. While Pump 1 High can be turned on and off, Pump 1 Low will run until set temperature is reached, or 1 hour has passed. -
Page 22: Exiting Priming Mode
PRIMING THE PUMPS As soon as the Priming Mode screeen appears on the panel, select the “Jets 1” button once to start Pump 1 in low-speed and then again to switch to high-speed. Also, select the other pumps, to turn them on. -
Page 23: Filtration And Ozone
FILTRATION AND OZONE On non-circ systems, Pump 1 low and the ozone generator (if installed) will run during filtration. On circ systems, the ozone will generally run with the circ pump, but can be limited to filtration cycles. The system is factory-programmed with one filter cycle that will run in the evening (assuming the time- of-day is properly set) when energy rates are often lower. -
Page 24: Saving Settings
SAVING SETTINGS The Time-of-Day screen is a simple, editable screen that illustrates a feature of the control that applies to all other editable screens as well. When changes are made, the icon to go “Back” changes to “Save” and a new icon for “Cancel” appears under the Save icon. -
Page 25: Circulation Pump Modes
CIRCULATION PUMP MODES Some spas may be manufactured with Circ Pump settings that allow programming filtration cycle duration. Some circ Modes are pre-programmed to operate 24 hours a day and are not programmable. Refer to the spa manufacturer’s documentation for any Circ Mode details. PURGE CYCLES In order to maintain sanitary conditions, as well as protect against freezing, secondary water devices will purge water from their respective plumbing by running briefly at the beginning of each filter cycle. -
Page 26: Drain Mode
UNLOCKING An Unlock Sequence using the navigation buttons can be used from the Lock Screen. The Unlock Sequence is the same for both Panel Lock and Settings Lock. HOLD MODE - M037* Hold Mode is used to disable the pumps during service functions like cleaning or replacing the filter. Hold Mode will last for 1 hour unless the mode is exited manually. - Page 27 Demo Mode: Demo Mode is not always enabled, so it may not appear. This is designed to operate several devices in a sequence in order to demonstrate the various features of a particular hot tub. Fault Log: The Fault Log is a record of the last 24 faults that can be reviewed by a service tech. ...
- Page 28 SYTEM INFORMATION The System Information Menu displays various settings and identification of the particular system. As each item in the menu is highlighted, the detail for that item is displayed at the bottom of the screen. Software ID (SSID): Displays the software ID number for the System. ...
-
Page 29: General Messages
Warning: The end-user must be trained to expect this one-time test to occur and how to properly reset the GFCI. If freezing conditions exist, the GFCI or RCD should be reset immediately or spa damage could result. CE Product: CE registered systems do not have an RCD Test Feature due to the nature of the electrical service. Some UL registered systems do not have the GFCI Test Feature activated. -
Page 30: Heater Related Messages
THE WATER IS TOO HOT – M029 The system has detected a spa water temp of 110°F (43.3°C) or more, and spa functions are disabled. System will auto reset when the spa water temp is below 108°F (42.2°C). Check for extended pump operation or high ambient temp. -
Page 31: Miscellaneous Messages
Sensors are out of sync -- Call for service* – M026 The temperature sensors ARE out of sync. The fault above has been established for at least 1 hour. Call for Service. Sensor A Fault, Senor B Fault – Sensor A: M031, Sensor B: M032 A temperature sensor or sensor circuit has failed. - Page 32 Check the sanitizer May appear on a regular schedule, i.e. every 7 days. Check sanitizer level and other water chemistry with a test kit and adjust with the appropriate chemicals. Clean the filter May appear on a regular schedule, i.e. every 30 days. Clean the filter media as instructed by the manufacturer.
- Page 33 Warning! Qualified Technician Required for Service and Installation Basic Installation and CSA Compliance/Conformité Caution: Configuration Guidelines Use minimum 6AWG copper conductors only. Torque field connections between 21 and 23 in lbs. Readily accessible disconnecting means to be provided at time of instal- in a pit.
- Page 34 Piping instructions of MONT BLANC Spa 30mA safety relay is need to be installed! E: Electric hole ( 600 mm) to terminal facilities through spa cabinet. 3 m cabels are required! L : Drain connector (5 0 0 mm) ...
- Page 35 1 Phase (Line) Connection to 1x32A (minimum) Advice to Mont Blanc modell...
- Page 36 3 Phase (Line) Connection to 3x16A (optimum) Advice to Mont Blanc modell...
Need help?
Do you have a question about the MONT BLANC and is the answer not in the manual?
Questions and answers