Toro 72105 Wheel Horse 268HE Operator's Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower
  5. 72105 Wheel Horse 268HE
  6. Operator's manual
Toro 72105 Wheel Horse 268HE Operator's Manual

Toro 72105 Wheel Horse 268HE Operator's Manual

Lawn & garden tractor
Hide thumbs
Table of Contents

Advertisement

Quick Links

FORM NO. 3321–854
Wheel Horse
268HE
Lawn & Garden
Tractor
Model No. 72105 – 9900001 & Up
Operator's Manual
IMPORTANT: Read this manual carefully. It contains information about your
safety and the safety of others. Also become familiar with the controls and
their proper use before you operate the product.
International English (GB)

Advertisement

Table of Contents
loading

Related Manuals for Toro 72105 Wheel Horse 268HE

Summary of Contents for Toro 72105 Wheel Horse 268HE

  • Page 1 FORM NO. 3321–854 Wheel Horse 268HE Lawn & Garden Tractor Model No. 72105 – 9900001 & Up Operator’s Manual IMPORTANT: Read this manual carefully. It contains information about your safety and the safety of others. Also become familiar with the controls and their proper use before you operate the product.
  • Page 2 The warning system in this manual identifies potential hazards and has special safety messages that All of us at Toro want you to be completely satisfied help you and others avoid personal injury, even death. with your new product, so feel free to contact your...

  • Page 3: Table Of Contents

    Contents Page Page Stopping the Machine ....Safety ....... . . Attachment Lift Lever .

  • Page 4: Safety

    Safety Safe Operation Practices for All drivers should seek and obtain professional and practical instruction. Such instruction should Ride-on (riding) Rotary emphasize: Lawnmower Machines the need for care and concentration when working with ride-on machines; This machine meets or exceeds European control of a ride-on machine sliding on a Standards in effect at the time of production.
  • Page 5 Safety If fuel is spilled, do not attempt to start the When using any attachments, never direct engine but move the machine away from discharge of material toward bystanders nor the are of spillage and avoid creating any allow anyone near the machine while in source of ignition until petrol vapors have operation.

  • Page 6: Sound Pressure Level

    Safety before making height adjustment unless To reduce the fire hazard, keep the engine, adjustment can be made from the operator’s silencer, battery compartment and petrol storage position. area free of grass, leaves, or excessive grease. 14. Reduce the throttle setting during engine run-out Check the grass catcher frequently for wear or and, if the engine is provided with a shut-off deterioration.

  • Page 7: Slope Chart

    Safety Slope Chart Read all safety instructions on pages 2–9.

  • Page 9: Symbols Glossary

    Safety Symbols Glossary Safety alert symbol Dismemberment–Mower in rearward motion Safety alert symbol Stay a safe distance from the machine Read operator’s manual Stay a safe distance Consult Technical Manual for from the mower proper service procedures Keep children a safe distance Thrown or flying objects–...

  • Page 10: Symbols Glossary

    Safety Symbols Glossary Cutting element– Riding on this machine is allowed basic symbol only on a passenger seat & only if the driver’s view is not hindered Cutting element– height adjustment Crushing of fingers or hands–Force applied Cutting unit–lower from side Cutting unit-raised Kickback or upward motion–Stored energy...

  • Page 11: Symbols Glossary

    Safety Symbols Glossary Fuel Fast Slow Fuel level Decreasing/Increasing Volume empty On/Run Volume full Off/Stop Engine Battery charging conditin Engine start Head lights– Main/high beam Engine stop Brake system Choke Parking brake Clutch Engine temperature PTO (Power Take Off) Engine lubricating Engage oil pressure Disengage...

  • Page 12: Gasoline And Oil

    Gasoline and Oil Recommended Gasoline Use UNLEADED Regular Gasoline suitable for POTENTIAL HAZARD automotive use (85 pump octane minimum). Leaded In certain conditions gasoline is extremely regular gasoline may be used if unleaded regular is flammable and highly explosive. not available. WHAT CAN HAPPEN IMPORTANT: Never use methanol, gasoline A fire or explosion from gasoline can burn...

  • Page 13: Stabilizer/Conditioner

    Gasoline and Oil Stabilizer/Conditioner Filling the Fuel Tank Add the correct amount of gas stabilizer/conditioner Shut the engine off and set the parking brake. to the gas. Using a stabilizer/conditioner in the Clean around each fuel tank cap and remove the machine: cap.

  • Page 14: Operation

    Operation Think Safety First Key Choice Switch Please carefully read all the safety instructions and A turn and release switch used for deactivating the symbols in the safety section. Knowing this “Operating–In–Reverse” interlock feature. Located information could help you, your family, pets or on the seat bracket on the right hand just below the bystanders avoid injury.

  • Page 15: Releasing The Parking Brake

    Operation Releasing the Parking Brake Move throttle lever to “FAST” (Fig. 5). Turn the ignition key clockwise and hold it in Push down on the brake pedal (Fig. 3). The the “START” position (Fig. 6). When the engine parking brake lever should release. starts, release the key.

  • Page 16: Operating The Power Take Off (Pto)

    Operation Stopping Engaging the Power Take Off (PTO) Move the throttle lever to “SLOW” (Fig. 5). Depress the brake pedal to stop the machine. Turn the ignition key to “OFF” (Fig. 6). Pull the power take off (PTO) to “ON” (Fig. 7). Note: If the engine has been working hard or is hot, let it idle for a minute before...

  • Page 17: The Safety Interlock System

    Operation The Safety Interlock System the tractor’s engine might prevent you from being aware that a child or a bystander has entered the area where you are operating the tractor. Understanding the Safety Interlock System If you are certain that you can safely mow in reverse or operate an attachment, deactivate the The safety interlock system is designed to prevent the operating–in–reverse interlock feature by turning the...

  • Page 18: Testing The Safety Interlock System

    Operation Set the parking brake. Move the power take off (PTO) to “ON”. Now turn the ignition key to “START”; the engine should not crank. POTENTIAL HAZARD Push the power take off (PTO) to “OFF” and A child or bystander could be backed over release the parking brake.

  • Page 19: Indicator Control Module

    Operation Indicator Control Module The oil light will be “ON” when the key is in the The indicator control module (Fig. 9) contains lights “RUN” or “LIGHTS” positions and the engine is not for: running, after the engine is started the light should go out.

  • Page 20: Driving Forward Or Backward

    Operation Driving Forward or Backward Stopping the Machine The throttle control regulates the engine speed as To stop the machine, release the traction control measured in rpm (revolutions per minute). Place the pedal, disengage the power take off (PTO), and turn throttle control in the “FAST”...

  • Page 21: Attachment Lift Lever

    Operation Attachment Lift Lever Adjusting Dial-A-Height The attachment lift lever (Fig. 11) is used to raise and The Dial-A-Height control (Fig. 11) is used to limit lower various attachments. the downward travel of the attachment. The Dial-A-Height knob is rotated to change the location of this stop, up or down.

  • Page 22: Positioning The Seat

    Operation Positioning the Seat Positioning the Tilt Steering Wheel The seat can move forward and backward. Position the seat where you have the best control of the The steering wheel has four tilt locations. Position the machine and are most comfortable. steering wheel where you have the best control of the machine and are most comfortable.

  • Page 23: Using The Cruise Control

    Operation Using the Cruise Control Pushing the Machine by Hand The cruise control is optional on some models. A IMPORTANT: Always push the machine by three position Lock–Set (spring loaded), On and hand. Never tow the machine because Unlock–Off dash switch (Fig. 15) controls the transaxle damage may occur.

  • Page 24: Maintenance

    Maintenance Service Interval Chart Each Storage Spring Service Operation Hours Hours Hours Hours Service Service Oil—check level Oil—change* Initial Oil Filter—change* (200 hours, every other oil change or yearly) Safety System—check Brake—check 200 hours Chassis—grease* Foam Air Cleaner—service* Paper Air Cleaner—replace* Spark Plug(s)—check Belts—check for wear/cracks Gasoline—drain...

  • Page 25: Air Cleaner

    Maintenance Air Cleaner Carefully slide the foam element off the paper element (Fig. 17). Service Interval/Specification Unscrew the cover nut and remove the cover and paper element (Fig. 17). Foam Element: Clean and re-oil after every 25 operating hours, or yearly, whichever occurs first. Cleaning the Foam and Paper Elements Paper Element: Replace after every 100 operating hours or yearly, whichever occurs first.
  • Page 26 Maintenance Paper Element Installing the Foam and Paper Elements A. Lightly tap the element on a flat surface to IMPORTANT: To prevent engine damage, remove dust and dirt (Fig. 19). always operate the engine with the complete foam and paper air cleaner assembly B.

  • Page 27: Engine Oil

    Maintenance Engine Oil Checking Oil Level Park the machine on a level surface, disengage Service Interval/Specification the power take off (PTO), set the parking brake, and turn the ignition key to “OFF” to stop the Change oil: engine. Remove the key. After the first 5 operating hours.
  • Page 28 Maintenance Changing/Draining Oil Change Oil Filter Service Interval/Specification Start the engine and let it run five minutes. This warms the oil so it drains better. Replace the oil filter every 200 hours or every other Park the machine so that the drain side is slightly oil change.

  • Page 29: Spark Plug

    Maintenance Spark Plug Checking the Spark Plug Look at the center of the spark plug(s) (Fig. 24). Service Interval/Specification If you see light brown or gray on the insulator, the engine is operating properly. A black coating Check the spark plug(s) after every 200 operating on the insulator usually means the air cleaner is hours.

  • Page 30: Greasing And Lubrication

    Maintenance Greasing and Lubrication Lubricate the traction control pedal on hydrostatic models (or brake and clutch pedals on gear drive models) where they pivot on Service Interval/Specification mounting shaft (Fig. 26). Grease the machine after every 50 operating hours or yearly, whichever occurs first.

  • Page 31: Brake

    Maintenance Brake Adjusting the Brake The brake lever is on top of the transaxle (Fig. 28). If Always set the parking brake when you stop the the parking brake does not hold securely, an machine or leave it unattended. If the parking brake adjustment is required.

  • Page 32: Fuel Tank

    Maintenance Fuel Tank Pull the fuel line off the filter (Fig. 30). Open fuel shut-off valve and allow gasoline to drain into a gas can or drain pan. Draining The Fuel Tank Note: Now is the best time to install a new fuel filter because the fuel tank is empty.

  • Page 33: Fuel Filter

    Maintenance Fuel Filter Front Wheel Toe-In Service Interval/Specification Service Interval/Specification Replace the fuel filter after every 100 operating hours Maintain toe-in of the front wheels as specified. If or yearly, whichever occurs first. uneven tire wear, lawn scuffing or hard steering develop adjustment may be required.

  • Page 34: Transaxle Fluid

    Maintenance Adjusting Toe-In Transaxle Fluid Check the toe-in before you adjust it; refer to Service Interval/Specification Measuring Toe-In, Page 31. Check fluid level after every 100 hours or yearly Remove ball joint from one steering lever whichever comes first. Always keep the fluid level at (Fig.

  • Page 35: Fuse

    Maintenance Fuse Service Interval/Specification The electrical system is protected by fuses. It requires no maintenance, however, if a fuse blows check component/circuit for malfunction or short. To replace fuses pull up on the fuse (Fig. 34) to remove or replace it. 2344 Figure 34 Fuse:...

  • Page 36: Headlights

    Maintenance Headlights Installing the Bulb The bulb has metal pins on the side of its base. Specification: Bulb # 1156 Automotive Type Align the pins with the slots in the bulb holder and insert the base into the holder (Fig. 36). Removing the Bulb Push and rotate the bulb clockwise until it stops.

  • Page 37: Battery

    Maintenance Battery Service Interval/Specification Check the electrolyte level in the battery before each use. Always keep the battery clean and fully charged. Use a paper towel to clean the battery case. If the battery terminals are corroded, clean them with a solution of four parts water and one part baking soda.

  • Page 38: Installing The Battery

    Maintenance Installing the Battery Checking Electrolyte Level Install the battery into the chassis (Fig. 38). With the engine off, open the hood to see the battery. Secure battery in chassis with hold down rods. Open covers to see into the cells. The electrolyte Using the bolt and wing nut, connect the positive must be up to the lower part of the tube (red) cable to the positive (+) battery post...
  • Page 39 Maintenance Charging the Battery IMPORTANT: Always keep the battery fully charged (1.260 specific gravity). This is especially important to prevent battery damage when the temperature is below 32 F (0 C). Remove the battery from the chassis; refer to Removing the Battery, page 35. Check the electrolyte level;...

  • Page 40: Wiring Diagram

    Maintenance Wiring Diagram...
  • Page 41 Maintenance...

  • Page 42: Cleaning And Storage

    Maintenance Cleaning and Storage IMPORTANT: The battery must be fully charged to prevent it from freezing and being damaged at temperatures below 32 F (0 C). Disengage the power take off (PTO), set the A fully charged battery maintains its charge parking brake, and turn the ignition key to for about 50 days at temperatures lower than “OFF”...

  • Page 43: Troubleshooting

    Troubleshooting PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION Starter does not crank Blade control (PTO) is Move blade control (PTO) to ENGAGED. DISENGAGED. Parking brake is not on. Set parking brake. Operator is not seated. Sit on the seat. Battery is dead. Charge the battery.
  • Page 44 Troubleshooting PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION Engine overheats. Engine load is excessive. Reduce ground speed. Oil level in crankcase is low. Add oil to crankcase. Cooling fins and air passages Remove obstruction from under engine blower housing cooling fins and air passages. are plugged.

This manual is also suitable for:

72107

Table of Contents