Huawei Quidway S1700-24-AC User Manual & Installation Quick Start
Hide thumbs
Also See for Quidway S1700-24-AC:
- Manual (266 pages) ,
- Installation, quick start (8 pages)
Advertisement
Quick Links
Quidway S1700-24-AC Ethernet Switch
User Manual & Installation Quick Start
Quidway S1700-24-AC以太网交换机
快速安装指南以及简易使用说明书
Rev: 02
Tool List
工具参考
Crosshead screwdriver
Flathead screwdriver
十字螺丝刀
Claw hammer
Adjustable spanner
羊角锤
活动扳手
Accessories (S1700-24-AC)
设备附件介绍(S1700-24-AC)
Rubber pads
Captive nut
胶垫贴
浮动螺母
Precautions
注意事项
Before installation, take ESD-preventive measures, for example, wear ESD-preventive gloves or a wrist strap.
安装前请做好防静电保护措施，如配戴防静电手套或防静电手腕。
Installing the Device in a 19'' Cabinet
安装设备到19英寸标准机柜中
Fix the rack-mounting ears.
安装挂耳。
IEC cabinet (19 inch)
IEC 机柜(19英寸)
Fix the captive nuts.
安装浮动螺母。
Marker pen
一字螺丝刀
记号笔
ESD-preventive
防静电手套
M4 screw
M4螺钉
1U=44.45mm
M6 Plug bolt
Percussion drill(φ8 Drill bit)
M6膨胀螺栓
冲击钻（φ8钻头）
Cable tie
线扣
M6 screw
Long rack-mounting ear
M6 螺钉
Install the device in a cabinet.
安装设备到机柜。
1U
Use installation strip to fix the captive nuts.
使用安装条安装浮动螺母。
4
Service and Support
技术支持
Diagonal pliers
斜口钳
长挂耳
Advertisement
Related Manuals for Huawei Quidway S1700-24-AC
Summary of Contents for Huawei Quidway S1700-24-AC
- Page 1 Quidway S1700-24-AC Ethernet Switch User Manual & Installation Quick Start Quidway S1700-24-AC以太网交换机 快速安装指南以及简易使用说明书 Rev: 02 Tool List Service and Support 技术支持 工具参考 Crosshead screwdriver Flathead screwdriver Marker pen M6 Plug bolt Percussion drill(φ8 Drill bit) M6膨胀螺栓 十字螺丝刀 一字螺丝刀 记号笔 冲击钻（φ8钻头）...
- Page 2 Installing the Device on a Worktable 安装设备到工作台 Adhibit the rubber pads. Install the device on a worktable. 粘贴胶垫贴。 安装设备到工作台。 Rubber pads 胶垫贴 Powering on the System Installing the Device on a Wall 上电检查 安装设备到墙面 ●To prevent injuries, check that there is no electrical wire at the locations to be drilled before drilling holes in the wall. ●...
- Page 3 Connecting PGND Cables and Power Cables 连接保护地线和电源线 Connect the PGND cable. 连接地线。 Connect the AC power cable. 连接交流电源线。 ● Do not connect power cables when the device is powered on, so as to avoid injuries. ● Make sure that the protection grounding cable of the device is grounded. ●...
- Page 4 Ethernet cables 以太网线 Cable tie 线扣 Powering on the System 上电检查 ● Power on the device only when the input voltage is in the normal range. Test the AC input voltage for S1700-24-AC. The voltage should range from 100 VAC to 240 VAC. ●...