Download Print this page

Huawei s1700 series User Manual And Installation Manual

Hide thumbs Also See for s1700 series:

Advertisement

Quick Links

S1700 Series Ethernet Switches
User Manual & Installation Quick Start
S1700系列以太网交换机
快速安装指南以及简易使用说明书
Rev: 03
The device model is on the product nameplate. 设备的具体型号信息请从产品铭牌上获取。
S1700 Managed Series Ethernet Switches include S1700-28GFR-4P-AC、S1700-52GFR-4P-AC、S1700-28FR-2T2P-AC、S1700-52FR-2T2P-AC.
S1700网管型以太网交换机系列包含S1700-28GFR-4P-AC、S1700-52GFR-4P-AC、S1700-28FR-2T2P-AC、S1700-52FR-2T2P-AC。
Tool List
工具参考
Crosshead screwdriver
Flathead screwdriver
十字螺丝刀
Claw hammer
Adjustable spanner
羊角锤
活动扳手
Accessories
安装附件介绍
Rubber pads
Captive nut
胶垫贴
浮动螺母
Precautions
注意事项
Before installation, take ESD-preventive measures, for example, wear ESD-preventive gloves or a wrist strap.
安装前请做好防静电保护措施,如配戴防静电手套或防静电手腕。
Installing the Device in a 19'' Cabinet
安装设备到19英寸标准机柜/机架中
● Leave more than 1U space between the devices for proper heat dissipation.
● 设备与设备之间的距离必须大于1U。
Fix the rack-mounting ears.
安装挂耳。
IEC cabinet (19 inch)
IEC 机柜(19英寸)
Fix the captive nuts.
安装浮动螺母。
Marker pen
一字螺丝刀
记号笔
ESD-preventive
Cable tie
防静电手套
线扣
M4 screw
M4螺钉
1U=44.45mm
M6 Plug bolt
Percussion drill(φ8 Drill bit)
M6膨胀螺栓
冲击钻(φ8钻头)
Optical fiber bundling tape
光纤绑扎带
M6 screw
Short rack-mounting ear
M6螺钉
Install the device in a cabinet.
安装设备到机柜。
1U
Use installation strip to fix the captive nuts.
使用安装条安装浮动螺母。
4
Service and Support
技术支持
Diagonal pliers
斜口钳
短挂耳

Advertisement

loading

Summary of Contents for Huawei s1700 series

  • Page 1 S1700 Series Ethernet Switches User Manual & Installation Quick Start S1700系列以太网交换机 快速安装指南以及简易使用说明书 Rev: 03 The device model is on the product nameplate. 设备的具体型号信息请从产品铭牌上获取。 S1700 Managed Series Ethernet Switches include S1700-28GFR-4P-AC、S1700-52GFR-4P-AC、S1700-28FR-2T2P-AC、S1700-52FR-2T2P-AC. S1700网管型以太网交换机系列包含S1700-28GFR-4P-AC、S1700-52GFR-4P-AC、S1700-28FR-2T2P-AC、S1700-52FR-2T2P-AC。 Tool List Service and Support 技术支持 工具参考 Crosshead screwdriver...
  • Page 2 Installing the Device on a Worktable 安装设备到工作台 Adhibit the rubber pads. Install the device on a worktable. 粘贴胶垫贴。 安装设备到工作台。 Rubber pads 胶垫贴 Installing the Device on a Wall 安装设备到墙面 ●To prevent injuries, check that there is no electrical wire at the locations to be drilled before drilling holes in the wall. ●...
  • Page 3: Installing The Sfp Transceiver

    Installing the SFP Transceiver SFP收发器的安装 ● Please use the metal-covered optical module. ● Please use SFP transceiver to meet laser class 1 standard. ● 请使用有金属外壳的光模块。 ● 请使用SFP transceiver 满足 Laser Class 1。 Insert the transceiver with the optical connector Connect the LC connector to SFP transceiver. facing outward and the slot connector facing down.
  • Page 4 Laying out Cables 布放线缆 ● Do not stare at optical interfaces. The optical fiber contains laser light sources that hurt human eyes. ● Lay out and bundle power cables, optical fibers, and Ethernet cables separately, with the distances in between longer than 10 cm. ●...
  • Page 5 S1700-28FR-2T2P-AC对应图 1-24 Port LED 1-24 端口指示灯 GE1-GE4 Port LED GE1-GE4 端口指示灯 LED Indicator LED状态 Condition Description 状态 描述 On Green Internal power is operating normally. 绿色常亮 设备正常上电。 Power off. 设备未上电 。 熄灭 On Green System boots up or works abnormal. 绿色常亮...
  • Page 6 S1700-28GFR-4P-AC对应图 1-24 Port LED 1-24 端口指示灯 25-28 Port LED 25-28 端口指示灯 LED Indicator LED状态 Condition Description 状态 描述 On Green Internal power is operating normally. 绿色常亮 设备正常上电。 Power off. 。 设备未上电 熄灭 On Green System boots up or works abnormal. 绿色常亮...
  • Page 7 S1700-52FR-2T2P-AC对应图 1-48 Port LED 1-48 端口指示灯 GE1-GE4 Port LED GE1-GE4 端口指示灯 LED Indicator LED状态 Condition Description 状态 描述 On Green Internal power is operating normally. 绿色常亮 设备正常上电。 Power off. 设备未上电 。 熄灭 On Green System boots up or works abnormal. 绿色常亮...
  • Page 8 S1700-52GFR-4P-AC对应图 1-48 Port LED 1-48 端口指示灯 49-52 Port LED 49-52 端口指示灯 LED Indicator LED状态 Condition Description 状态 描述 On Green Internal power is operating normally. 绿色常亮 设备正常上电。 Power off. 。 设备未上电 熄灭 On Green System boots up or works abnormal. 绿色常亮...