1. Manuals
  2. Brands
  3. Sanyo Manuals
  4. Security Camera
  5. VCC-6975
  6. Instruction manual

Sanyo VCC-6975 Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

INSTRUCTION MANUAL

BEDIENUNGSANLEITUNG
MANUEL D'INSTRUCTIONS
COLOUR CCD camera
CCD-Farbkamera
Caméra CCD COULEUR
CCD
About this manual
Before installing and using the camera, please read this
manual carefully. Be sure to keep it handy for later reference.
Über diese Bedienungsanleitung
Lesen Sie bitte vor der Montage und dem Inbetriebnehmen der
Kamera zuerst diese Bedienungsanleitung sorgfältig durch und
bewahren Sie sie zum späteren Nachschlagen auf.
A propos de ce manuel
Avant d'installer et d'utiliser la caméra, veuillez lire ce
manuel attentivement. Gardez-le à portée de main
pour toute référence ultérieure.
VCC-6975P

Advertisement

Table of Contents
loading

Related Manuals for Sanyo VCC-6975

Summary of Contents for Sanyo VCC-6975

  • Page 1: Instruction Manual

    INSTRUCTION MANUAL VCC-6975P BEDIENUNGSANLEITUNG MANUEL D’INSTRUCTIONS COLOUR CCD camera CCD-Farbkamera Caméra CCD COULEUR About this manual A propos de ce manuel Before installing and using the camera, please read this Avant d’installer et d’utiliser la caméra, veuillez lire ce manual carefully. Be sure to keep it handy for later reference. manuel attentivement.

  • Page 2: Table Of Contents

    Depending on the conditions of use, installation and environment, please ZOOM setting ........43 be sure to make the appropriate settings and adjustments.

  • Page 3: Precautions

    Disconnect the power greasy smoke or steam, where the dampness may get too high, or cord immediately, and consult your dealer (or a Sanyo Authorized where there is a lot of dust.

  • Page 4: Parts Names

    PARTS NAMES Power indicator (POWER) Comes on when the power to the camera is on. Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. NOTE: When using this connector, the supplied clamping core (A) must be installed on the coaxial cable, to prevent electromagnetic interference from the other connected devices.
  • Page 5 PARTS NAMES Camera setup section (under the cover) To access the controls, loosen the cover fixing screw A, then remove the cover. Address setting switch (RS485 ADDRESS) . . . See page 56 Terminater switch (TERMINATE) ..See page 56 Auto iris lens switch (A.
  • Page 6 PARTS NAMES Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). Flange-back adjustment screw (FLANGE BACK ADJ) (See page 8) Flange-back lock screw (FLANGE BACK LOCK) Camera installation bracket The bracket can be fixed at the top or bottom of the camera.

  • Page 7: Concerning Auto-Iris Lenses

    ALC (Automatic Light Control) and LEVEL volume level controls are available on the lens for iris adjustments. (Set the A.I. LENS switch to the VIDEO position.) Compatible auto-iris lenses 1/3 inch Sanyo DC type lens VIDEO type lens VCL-CS8LY: Standard angle, f= 8 mm...

  • Page 8: Mounting The Lens

    MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). Checking the lens mount Do not use lenses with a length L more than 5 mm. If not, that may damage the camera and prevent proper installation. Remove the lens mount cap from the camera. Install the auto-iris lens.
  • Page 9 MOUNTING THE LENS Rewiring the lens cable in the lens iris plug Prepare the lens cable. Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire. Install the lens iris plug. Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close the plug cover.

  • Page 10: Connections

    CONNECTIONS Basic connection for monitoring or recording (Video signal connections) AC 24 V connection DC 12 V connection : VIDEO IN : VIDEO OUT AC24V DC12V DC12V – – Fig. 1 Fig. 2 The peripheral devices (VCR, monitor, lens, etc.) and cables are CAUTION: sold separately.
  • Page 11 CONNECTIONS Coaxial cable type and maximum length Camera control unit connections • Cable type RG-59U (3C-2V), 250 m maximum. This camera main MENU can be set remotely using a camera control unit (VAC-60, sold separately) connected between the camera and its •...
  • Page 12 CONNECTIONS Before making any connection, make sure all the peripheral devices are turned off. Multiple units are connected in series using twisted-pair cables (bridge CAMERA IN connection). To set the addresses and make other fine adjustments, terminal please refer to page 56. RS-485 terminal connections Connect a shielded twisted-pair cable (AWG22) from signal A to signal A, and from signal B to signal B of the RS485 control terminal...

  • Page 13: Using The Menu Screen

    USING THE MENU SCREEN This unit is set at the factory so that it can be used with a DC type auto-iris lens (sold separately). Therefore, under normal conditions, additional settings or adjustments are not necessary. Depending on the conditions of use, if settings or adjustments are required they can be done from the “MAIN MENU”...

  • Page 14: Notes Concerning The Menu Settings

    USING THE MENU SCREEN Notes concerning the menu settings • Modes that cannot be used together A) The IRIS item SENSE UP setting (other than OFF) and the MOTION item ON setting. B) The SHUTTER item LONG setting and the MOTION item ON setting. ADJUSTMENT FOR AI MAIN MENU MAIN MENU...

  • Page 15: Language Setting

    USING THE MENU SCREEN LANGUAGE LANGUAGE setting MAIN MENU Press the SET button for about 3 seconds. LANGUAGE The MAIN MENU screen will be displayed. CAMERA ID SYNC Press the CURSOR (j or l) button until “SET” in the LANGUAGE item is selected, then press the SET button.

  • Page 16: Camera Id Setting

    USING THE MENU SCREEN CAMERA ID CAMERA ID setting MAIN MENU Press the SET button for about 3 seconds. LANGUAGE The MAIN MENU screen will be displayed. CAMERA ID SYNC Press the CURSOR (l, then d or c) button to change the CAMERA ID setting to “ON”, then press the SET button.
  • Page 17 USING THE MENU SCREEN CAMERA ID Press the CURSOR (l) button to select “SET” as the POSITION setting (the setting will flash), then press the SET button. CAMERA ID SETTING CURSOR ABCDEFGHIJKLM The CAMERA ID SETTING screen will be displayed, and the set camera ID will flash at the NOPQRSTUVWXYZ position currently set.

  • Page 18: Sync Settings

    USING THE MENU SCREEN SYNC/INT Internal synchronization setting (INT) SYNC settings The following three types of synchronization settings can be carried Press the SET button for about 3 seconds. out. The MAIN MENU screen will be displayed. Internal synchronization (INT) Press the CURSOR (l, then d or c) button to change the SYNC setting to “INT”...

  • Page 19: B Power Supply Synchronization Setting (L - L)

    USING THE MENU SCREEN SYNC/L-L Power supply synchronization setting (L - L) When using a camera switcher to connect 2 cameras or more to one monitor, there may be a MAIN MENU CURSOR vertical roll of the images when switched. In such a case, set as described below. LANGUAGE Press the CURSOR (l, then d or c) button to change the SYNC setting to “L - L”...

  • Page 20: C External Sync Setting (Vbs)

    USING THE MENU SCREEN SYNC/VBS External sync setting (VBS) MAIN MENU Connect the output signal from the other camera to the external sync input LANGUAGE connector of this camera. CAMERA ID SYNC The SYNC setting in the MAIN MENU screen will change to VBS. Press the CURSOR (l) button to select the SYNC setting “VBS”...
  • Page 21 USING THE MENU SCREEN SYNC/VBS When finished: CURSOR Press the CURSOR (l) button to select BACK (it will flash) at the bottom of the screen. MENU BACK Then press the CURSOR (d or c) button to change BACK to END, and press the SET button.

  • Page 22: Iris Setting (Blc, Sense Up)

    USING THE MENU SCREEN AI/BLC•LENS TYPE AI (Auto Iris) mode setting IRIS setting The following two types of iris level adjustment can be carried out. Press the SET button for about 3 seconds. The MAIN MENU screen will be displayed. AI (Auto-Iris): This automatically adjusts the camera iris so that the optimum image can be obtained when an Press the CURSOR (l, then d or c) button to change the...
  • Page 23 USING THE MENU SCREEN AI/BLC•IRIS LEVEL Adjust the IRIS LEVEL setting (DC type lens only) Press the CURSOR (l) button so that the IRIS LEVEL value is flashing, then press the CURSOR (d or c) button to adjust the IRIS LEVEL setting. ADJUSTMENT FOR AI The larger the value, the greater the iris level.
  • Page 24 USING THE MENU SCREEN AI/BLC•MULTI BLC/MULTI (multi-spot photometry) mode setting (DC type lens only) ADJUSTMENT FOR AI CURSOR Press the CURSOR (j, then d or c) button so that “MULTI” is selected for BLC (the LENS TYPE MULTIp setting will flash), then press the SET button. SENSE UP The BLC MASKING screen will be displayed.
  • Page 25 USING THE MENU SCREEN AI/BLC•EVAL BLC/EVAL (5-section photometry) mode setting ADJUSTMENT FOR AI CURSOR Press the CURSOR (j, then d or c) button so that “EVAL” is selected for BLC (the LENS TYPE EVAL p setting will flash), then press the SET button. SENSE UP The ADJUSTMENT FOR BLC screen will be displayed, and the photometry mask will also be displayed in the center of the screen.
  • Page 26 USING THE MENU SCREEN AI/BLC•EVAL Press the CURSOR (l) button to select the photometry areas (TOP, etc.), and press the CURSOR (d or c) button to set the weighting (numeric value setting). Weighting • Setting is possible within the range of 0 to 15. •...

  • Page 27: Bei (Electronic Iris) Mode Setting

    USING THE MENU SCREEN AI/SENSE UP•EI EI (Electronic Iris) mode setting SENSE UP setting The EI mode setting is the same as for the AI mode setting with a DC Press the CURSOR (l) button so that the SENSE UP setting is at OFF type lens, please refer to page 21.

  • Page 28: White Balance Setting

    USING THE MENU SCREEN WHITE BALANCE/ATW Automatic color temperature tracking setting WHITE BALANCE setting (ATW) The following three types of white balance adjustment can be carried out. Press the SET button for about 3 seconds. Automatic color temperature tracking (ATW: Auto Trace The MAIN MENU screen will be displayed.
  • Page 29 USING THE MENU SCREEN WHITE BALANCE/ATW•MASKING If there is a bright light source appearing on the screen, it may interfere with the white balance setting. In such cases, use the MASKING setting function to mask excessively bright areas so that they are not detected. MASKING setting Press the CURSOR (l, then d or c) button to change the WHITE BALANCE setting to “ATW”...
  • Page 30 USING THE MENU SCREEN WHITE BALANCE/ATW•MASKING When all masks have been applied, press the CURSOR (l) button to move the mask cursor to the bottom edge of the screen, and continue pressing the CURSOR button for about 3 seconds. Returning to the default setting Press the CURSOR (l, then d or c) button to change the PRESET setting to ON, then press the SET button.

  • Page 31: B Push-Lock White Balance Adjustment (Awc)

    USING THE MENU SCREEN WHITE BALANCE/AWC Push-lock white balance adjustment (AWC) CURSOR MAIN MENU Press the CURSOR (l, then d or c) button to change the WHITE BALANCE setting LANGUAGE to “AWC” (the setting will flash), then press the SET button. CAMERA ID SYNC The ADJUSTMENT FOR AWC screen will be displayed.

  • Page 32: C Manual White Balance Setting (Mwb)

    USING THE MENU SCREEN WHITE BALANCE/MWB Manual white balance setting (MWB) CURSOR MAIN MENU Press the CURSOR (l, then d or c) button to change the WHITE BALANCE setting LANGUAGE to “MWB” (the setting will flash), then press the SET button. CAMERA ID SYNC The ADJUSTMENT FOR MWB screen will be displayed.

  • Page 33: Electronic Shutter Setting

    USING THE MENU SCREEN SHUTTER Electronic SHUTTER setting The following two types of shutter speed functions are available. Short mode (SHORT): This shortens the exposure time so that you can film subjects which are moving quickly. Long exposure mode (LONG): This is used for making dark scenes lighter, such as when filming at nighttime.

  • Page 34: A For Short Mode

    USING THE MENU SCREEN SHUTTER/SHORT For SHORT mode MAIN MENU Press the SET button for about 3 seconds. LANGUAGE CURSOR CAMERA ID The MAIN MENU screen will be displayed. SYNC IRIS Press the CURSOR (l, then d or c) button to change the SHUTTER setting to WHITE BALANCE SHUTTER SHORTp...

  • Page 35: B For Long Mode

    USING THE MENU SCREEN SHUTTER/LONG For LONG mode MAIN MENU Press the CURSOR (l, then d or c) button to change the SHUTTER setting to LANGUAGE CURSOR “LONG” (the setting will flash), then press the SET button. CAMERA ID SYNC The ADJUSTMENT FOR ES screen will be displayed.

  • Page 36: Motion Setting

    USING THE MENU SCREEN MOTION MOTION setting For the MOTION setting, the screen area is split up into 64 (8 X 8) detection areas where movements (or changes) are detected. MAIN MENU LANGUAGE Then, using the SENSITIVITY and other menu settings, these CURSOR CAMERA ID SYNC...
  • Page 37 USING THE MENU SCREEN MOTION The following settings can be made from the MOTION menu. Note: Operating direction detection function (DIRECTION): • If the whole background is empty, detection may not be performed Sets the camera to detect only movement in a certain direction. properly.

  • Page 38: Adirection Setting

    USING THE MENU SCREEN MOTION/DIRECTION DIRECTION setting Press the SET button for about 3 seconds. Press the CURSOR (j or l) button to select the DIRECTION setting The MAIN MENU screen will be displayed. OFF (the setting will flash), then press the CURSOR (d or c) button Press the CURSOR (l, then d or c) button to change the repeatedly.

  • Page 39: Bsize Setting

    USING THE MENU SCREEN MOTION/SIZE Fig. 1 SIZE setting SIZE setting Subject (Example) The SIZE setting will split the screen area in 64 (8 x 8) squares and Size A B C D the detection is made by measuring movement and changes in each of the squares.
  • Page 40 USING THE MENU SCREEN MOTION/SIZE MOTION SIZE display table V 1, H 1 V 2, H 1 V 3, H 1 V 8, H 1 V 2, H 2 V 2, H 3 V 3, H 2 V 3, H 3 V 4, H 2 V 2, H 4 V 1, H 2...

  • Page 41: Cmasking Setting

    USING THE MENU SCREEN MOTION/MASKING MASKING setting CURSOR ADJUSTMENT FOR MOTION Press the CURSOR (l, then d or c) button to set MASKING to “ON” (the setting DIRECTION will flash), then press the SET button. SIZE MASKING The MOTION MASKING screen will be displayed, and the mask cursor will flash in the top-left corner of the screen.
  • Page 42 USING THE MENU SCREEN MOTION/MASKING When finished: CURSOR Press the CURSOR (l) button to select BACK (it will flash) at the bottom of the screen. MENU BACK Then press the CURSOR (d or c) button to change BACK to END, and press the SET button.

  • Page 43: Dsensitivity Setting

    USING THE MENU SCREEN MOTION/SENSITIVITY SENSITIVITY setting The smaller the setting value, the greater the sensitivity. Press the CURSOR (l) button to select the SENSITIVITY setting “SET” (the setting will flash), CURSOR ADJUSTMENT FOR MOTION then press the SET button. DIRECTION SIZE The SENSITIVITY screen will be displayed.

  • Page 44: Ezoom Setting

    USING THE MENU SCREEN MOTION/ZOOM DURATION This sets how long the moving subject should be on the screen before it is detected. A lower setting will set a longer on screen duration before the subject is detected. Press the CURSOR (l, then d or c) button so that the DURATION value is flashing. (Maximum: 60) Set the value to a large if objects which are moving fast are not to be detected.

  • Page 45: Finterval Setting

    USING THE MENU SCREEN MOTION/INTERVAL, ALARM SIGN INTERVAL setting ADJUSTMENT FOR MOTION Press the CURSOR (l) button so that the INTERVAL value is flashing, then press the CURSOR DIRECTION (d or c) button repeatedly. SIZE MASKING After an alarm signal has been output once, this sets the length of time that no further alarm SENSITIVITY CURSOR ZOOM...

  • Page 46: Motion Detector Setting Example

    USING THE MENU SCREEN MOTION/Example Motion detector setting example After the camera has been connected to the peripheral devices (VCR, multiplexer, etc.) set the MOTION item to send an alarm trigger to the peripheral devices when the set movement parameters are met. Checking the detected movements set by the MOTION item If the MOTION item settings are not made properly, the desired results will not be obtained.
  • Page 47 USING THE MENU SCREEN MOTION/Example DIRECTION setting Select the desired direction arrows (ex.: íí). The detection will be done when the subject moves in DIRECTION the direction of the arrows. For example, the setting can be done in order to detect a subject entering a room, but ignored when it is going out of the room.
  • Page 48 USING THE MENU SCREEN MOTION/Example SENSITIVITY setting From the SENSITIVITY SET item switch to the SENSITIVITY screen. In this screen, the sensitivity level setting will be higher towards the left and lower towards the right. Note: If all the settings values are too large, alarm triggering may not operate as desired. •...

  • Page 49: Option Settings

    USING THE MENU SCREEN OPTION OPTION settings Press the SET button for about 3 seconds. The MAIN MENU screen will be displayed. The following settings can be made from the OPTION menu. Press the CURSOR (l) button to select the OPTION setting APERTURE setting: “SET”...

  • Page 50: Aaperture Setting

    USING THE MENU SCREEN OPTION/APERTURE APERTURE setting Press the CURSOR (d or c) button to change the APERTURE setting to “ON” (the CURSOR OPTION MENU setting will flash), then press the SET button. APERTURE The ADJUSTMENT FOR APERTURE screen will be displayed. Press the CURSOR (d or c) button so that the H (horizontal) value flashes, then ADJUSTMENT FOR APERTURE correct the outlines in the horizontal direction.

  • Page 51: Bagc Setting

    USING THE MENU SCREEN OPTION/AGC, GAMMA AGC setting CURSOR OPTION MENU Press the CURSOR (l, then d or c) button to change the AGC setting to ON or APERTURE OFF (the setting will flash). When finished: CURSOR Press the CURSOR (l) button to select BACK (it will flash) at the bottom of the screen. MENU BACK Then press the CURSOR (d or c) button to change BACK to END, and press the SET...

  • Page 52: Dzoom Setting

    USING THE MENU SCREEN OPTION/FIXI ZOOM, PAN ZOOM setting OPTION MENU CURSOR Press the CURSOR (l, then d or c) button to change the ZOOM setting to “ON” APERTURE (the setting will flash), then press the SET button. GAMMA The ZOOM screen will be displayed. ZOOM The ADJUSTMENT FOR ZOOM screen will be displayed.
  • Page 53 USING THE MENU SCREEN OPTION/FIXI TILT TILTING: CURSOR • Press the CURSOR (l) button to select the TILT setting “UP” (the setting will flash), then TILT DOWN press and hold the SET button. The picture will tilt upward. • Press the CURSOR (c) button to select the TILT setting “DOWN” (the setting will flash), then press and hold the SET button.
  • Page 54 USING THE MENU SCREEN OPTION/VAR ZOOM, PAN For VAR mode ADJUSTMENT FOR ZOOM Press the CURSOR (d or c) button to select “VAR” as the MODE setting. CURSOR MODE WIDE and TELE will appear automatically for ZOOM. ZOOM WIDE TELE LEFT RIGHT ZOOMING:...
  • Page 55 USING THE MENU SCREEN OPTION/VAR ZOOM, TILT TILTING: • Press the CURSOR (l) button to select the TILT setting “UP” (the setting will flash), then CURSOR TILT DOWN press and hold the SET button. The picture will tilt upward. • Press the CURSOR (c) button to select the TILT setting “DOWN”...

  • Page 56: Emirror Setting

    USING THE MENU SCREEN OPTION/MIRROR, RS-485 MIRROR setting OPTION MENU CURSOR Press the CURSOR (l, then d or c) button to change the MIRROR setting to “H” APERTURE (the setting will flash). GAMMA The image will be inverted horizontally. The image will change as described below each time ZOOM MIRROR the CURSOR button is pressed.

  • Page 57: Address Setting

    USING THE MENU SCREEN OPTION/RS-485 ADDRESS setting If the ADDRESS setting on the screen is 0, this means that the camera’s RS-485 address is MENU FOR RS-485 CURSOR currently set to 0. If the address is changed using the address setting switches at the side of the BAUD RATE 19200 camera as shown in the illustration, the new address will be displayed on the screen.

  • Page 58: Ginitial Setting

    USING THE MENU SCREEN OPTION/INITIAL INITIAL setting This lets you return all settings to the factory defaults. OPTION MENU CURSOR SET APERTURE Press the CURSOR (l, then d or c) button to set INITIAL to “ON” then press the GAMMA SET button.

  • Page 59: Operations Using The System Controller

    OPERATIONS USING THE SYSTEM CONTROLLER Operations using the camera MENU screens Press the INDIVIDUAL button. Press the MODE button to select CM. MAIN MENU LANGUAGE Use the numeric buttons to enter the address (camera). CAMERA ID SYNC Press the ENTER button to accept the address. IRIS WHITE BALANCE Press the MENU button.
  • Page 60 OPERATIONS USING THE SYSTEM CONTROLLER Operations using the camera command B: Iris level operations (CAMERA) button If using a DC-type auto-iris lens, the iris opening can be controlled. If using a video-type or manual-type auto-iris lens, no operation can be Press the INDIVIDUAL button.
  • Page 61 OPERATIONS USING THE SYSTEM CONTROLLER C: Setting the SENSE UP and electronic shutter D: Backlight compensation settings 1) If the SHUTTER setting in the camera’s main menu is set to 1) Turning backlight compensation on LONG or SHORT, you can change the SHUTTER SPEED setting. Press the BLC button then press the “+”...

  • Page 62: Menu Display

    MENU DISPLAY 4321 LANGUAGE CAMERA ID SETTING CAMERA ID SETTING LANGUAGE ABCDEFGHIJKLM LANGUAGE ENGLISH NOPQRSTUVWXYZ LANGUE FRENCH 0123456789 :- MAIN MENU SPRACHE GERMANY CAMERA ID IS ???????? LANGUAGE ???????? POSITION SET p CAMERA ID SYNC IRIS SYNC ADJUSTMENT WHITE BALANCE SHUTTER ADJUSTMENT FOR L-L MOTION...
  • Page 63 MENU DISPLAY WHITE BALANCE SETTING ELECTRIC SHUTTER (IRIS MODE : AI only) ADJUSTMENT FOR ES SHORTp ADJUSTMENT FOR ATW 50, 120, 250, 500, ATW MASKING 1000, 2000, 4000 SHUTTER SPEED MASKING 10000 ADJUSTMENT FOR ES LONG p ADJUSTMENT FOR AWC ADJUSTMENT FOR MWB SHUTTER SPEED X1, X2, X4, X8,...

  • Page 64: Troubleshooting

    This camera is a precision instruments and if treated with care, will provide years of satisfactory performance. However, in the event of a problem, the owner is advised not to attempt to make repairs or open the cabinet. Servicing should always be referred to your dealer or Sanyo Authorized Service Center.

  • Page 65: Specifications

    SPECIFICATIONS Camera: Electronic shutter 8 speeds, selectable by setting • SHORT: 1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, Scanning system PAL standard (625 TV lines, 1/10000 sec. 25 frames/sec.) • LONG: X1, X2, X4, X8, X16, X32 Interlace PLL 2:1 interlace Electronic sensitivity AUTO/OFF, up to X32 Image device...
  • Page 66 SPECIFICATIONS Dimensions: mm 126.5 1/4”–20 UNC 22.8 Features and specifications are subject to change without prior notice or obligations. English...

  • Page 67: Accessories

    ACCESSORIES C mount adaptor (5 mm)............1 pc. The C mount adaptor must be used to be able to install a C mount lens on the camera. Lens iris plug (4-pin)..............1 pc. Clamping core A ............... 2 pc. Clamping core B ............... 1 pc. Clamping core C ...............
  • Page 68 Sanyo Electric Co, Ltd. 1AC6P1P2280-- Printed in Japan L53R2/XE(0400KP-NI)

Table of Contents