Table of Contents
Advertisement
Various search (continued)
ALARM LIST SEARCH
This unit stores the start time of alarm recording and emer-
gency recording in the alarm list when such recording be-
gins. It is also possible to index search the desired time (or
the closest time) from the list of alarm recording (emer-
gency recording) start times stored in the alarm list.
Up to 10,000 alarm recording (emergency re-
cording) start times can be stored and displayed.
In the alarm list, items with the ALARM IN termi-
nal on the rear grounded are indicated in white, items
that were detected with motion are indicated in green
and items with the EMERGENCY terminal grounded
are indicated in red.
To clear the alarm list, erase the data in the
<MAIN HDD DATA CLEAR> and <SUB HDD DATA
CLEAR> screen. Beware that executing it erases
all the data of HDD contained the video data. Alarm
recording then will be stored again from 00001.
1. Press the SEARCH button.
• The search screen selected in the "SEARCH TYPE" (
see page 75 ) appears.
<SEARCH SELECTION>
>>SEARCH TYPE
SELECTION CAMERA NUMBER
DATE/TIME
PLAYBACK DEVICE
MAIN
START
END
The Alarm list may take time to display completely
when there are many list items or the HDD has been
expanded.
2. (When the desired search screen is not displayed on the
screen • • • )
Change the above "SEARCH TYPE" setting and display the
"ALARM LIST SEARCH" screen.
• To display the emergency recording start time in the alarm
list, set "SELECTION CAMERA NUMBER" in the <SEARCH
SELECTION> screen to "ALL". "EMR" indicating emergency
recording will appear in the place of the camera number in
the alarm list.
<ALARM LIST SEARCH>
>>00004 01-01-2003 00:00:04
00003 01-01-2003 00:00:03 EMR
00002 01-01-2003 00:00:02
00001 01-01-2003 00:00:01 EMR
PUSH SEARCH KEY
"Camera of alarm input" displays the camera
number which activated the alarm signals, and
"record camera" displays the camera number which
started recording.
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
78
ALARM LIST
ALL
-
-
:
:
MAIN
02-02-2003 00:00:00
04-04-2003 12:30:15
2
1
1
1
When a cameras picking up an alarm signal is
not set to record, the recorded video will be stored
in the lowest number (active) camera.
When executing on "ALARM LIST SEARCH"
function and the "PARTITION" active, set " PLAY-
BACK DEVICE" to "SUB".
3. Select the desired alarm list number.
•
button/turn JOG dial counterclockwise : Selection moves
to the next number.
•
button/turn JOG dial clockwise : Selection moves to the
previous number.
•
button : Displays the page with date prior to the date of
the currently opened page.
•
button : Displays the page with date newer than the date
of the currently opened page.
• To cancel search, press the SEARCH button twice.
The camera number written by the start index
signal of the pre-alarm recording may differ from the
camera number displayed in the alarm list.
When setting "HDD REPEAT REC MAIN" to
"OFF" or "STANDBY", "HDD REPEAT REC SUB" to
"OFF" and there is an alarm recording (emergency
recording) at the end of the HDD, that recording may
not be stored in the alarm list and that number may
become missing and not displayed.
When an alarm recording (emergency record-
ing) is performed when displaying of the <ALARM
LIST SEARCH> screen, exit the <ALARM LIST
SEARCH> screen and display the screen again. The
new item will be added to the list.
When using "DATE/TIME" in the <SEARCH SE-
LECTION> screen, the number of list items dis-
played on the screen can be narrowed down.
1. Press the SEARCH button to display the <SEARCH
SELECTION> screen.
2. Set the desired date and time of the result in "DATE/TIME"
and confirm.
3. Turn the SHUTTLE ring counterclockwise once to display
narrowed-down list.
4. Select the desired alarm list number and turn the
SHUTTLE ring clockwise to confirm.
• To cancel the search, press the SEARCH button twice.
• After performing alarm search, the screen will be in the single
screen display with still-frame playback regardless of whether
setting "ALL" in the "SELECTION CAMERA NUMBER" (
see page 75 ) or selecting an individual camera number.
5. Playback the search result.
• Press either the PLAY (REV. PLAY) or PAUSE button.
6. To stop playback or still-frame playback, press the STOP
button.
Advertisement
Table of Contents
