Advertisement
Quick Links
MODEL 84000
MODEL 8400DW
With Fast Charger
Capacities
Steel
Wood
Concrete
Wood screw
1 0 "
1 2 mm
1 0 "
3.8
mm
x 2 0 m m
(318")
(112")
1318")
(118" x 314")
INSTRUCTION MANUAL
Net
No load
Blows
per
Overall
speed
(RPM]
minute
length
weight
2 6 0 mm
1.7 k g
io'ooo
(10-114")
( 3 . 7 Ibs)
SPECIFICATIONS
Voltage
9.6 V
Model 8400D
Charging time
Input
o u t p u t
1 Hr.
A.C. only 50 Hz
-
6 0 Hz
D.C. 7 . 2 V
-
9 . 6 V
Advertisement
Related Manuals for Makita 8400D
Summary of Contents for Makita 8400D
- Page 1 INSTRUCTION MANUAL SPECIFICATIONS Model 8400D Capacities Steel Wood Concrete 1 0 ” 1 2 mm 1 0 ” (318”) 1318”) (112”) Voltage Charging time 9.6 V 1 Hr. No load speed Wood screw (RPM] minute x 2 0 m m io'ooo (118”...
-
Page 2: Important Safety Instructions
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. - Page 3 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. OUTDOOR USE EXTENSION CORDS.
- Page 4 Before using battery charger, read all instructions and cautionary markings battery charger, CAUTION To reduce risk of injury, charge only MAKITA Battery 9000 9100. Other types of batteries may burst causing personal injury and damage.
-
Page 5: Additional Safety Rules
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) (104OF). or ABOVE 4OoC 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. - Page 6 Installing or removing battery cartridge Always switch off the tool before insertion or removal of the battery cartridge. To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing from the barrel.
- Page 7 When you charge a new battery cartridge or a battery cartridge which has not been used long period, may not accept not indicate problem. You can recharge the battery cartridge fully after discharging it almost completely a couple of times. wish to charge fast charger.
- Page 8 Switch action Move the reversing switch lever to the "FWD" position for clockwise rotation or the "REV" position for counterclockwise. To start the tool, simply pull the trigger. Release the trigger to stop. When the re- versing switch lever is in the neutral posi- tion, the tool will not start even if you pull the trigger.
- Page 9 Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. the tool/bit the time Bit No.
- Page 10 ACCESSOR I ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The of any other accessories or attachments might present a risk of injury t o persons. The accessories or attachments should be used only in the proper and intended manner.
- Page 11 o ~ t 10 mm (3/8") CORDLESS HAMMER DRILL Model 84000 Note: The switch and other part conflguratlons may differ from country t o country...
- Page 12 MAKmA L I M I T E D ONE YEAR WARRANTY Every Makita tool is thorou ly inspected and tested before leaving the factory. It is warranted be free of defects from wor&iship and materials for the period of ONE YEAR from the date of original purchase.