Panasonic WV-CP500 Installation Manual
Color cctv camera
Hide thumbs
Also See for WV-CP500:
- Operating instructions manual (35 pages) ,
- Specification (2 pages) ,
- Product catalog (125 pages)
Table of Contents
Advertisement
Quick Links
Installation Guide
Color CCTV Camera
WV-CP500/G
Model No.
WV-CP504E
This illustration represents WV-CP500/G.
Lens: Option
Before attempting to connect or operate this product, please read these
instructions carefully and save this manual for future use.
The model number is abbreviated in some descriptions in this manual.
Advertisement
Table of Contents
Related Manuals for Panasonic WV-CP500
Summary of Contents for Panasonic WV-CP500
- Page 1 Color CCTV Camera WV-CP500/G Model No. WV-CP504E This illustration represents WV-CP500/G. Lens: Option Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number is abbreviated in some descriptions in this manual.
- Page 2 WARNING: • This apparatus must be earthed. • Apparatus shall be connected to a mains socket outlet with a protective earthing con- nection. • The mains plug or an appliance coupler shall remain readily operable. • To prevent fire or electric shock hazard, do not expose this apparatus to rain or moisture.
-
Page 3: Important Safety Instructions
Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instruc- tions. -
Page 4: Limitation Of Liability
IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S). Disclaimer of warranty IN NO EVENT SHALL Panasonic Corporation BE LIABLE TO ANY PARTY OR ANY PERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE CASES, INCLUDING BUT NOT LIMITED TO BELOW:... -
Page 5: Preface
Preface This product is a 1/3-inch type {1/3"} CCD color CCTV camera. Connection of this product to a video monitor allows users to use this product as a monitoring camera. • WV-CP500: 220 to 240 V AC power supply • WV-CP504: 24 V AC, 12 V DC power supply Introduction of SUPER-D5 (super dynamic function) Integration of SUPER-D5 into the CCD and signal processing circuit has achieved approximately 160 times higher dynamic range as compared with conventional camera. -
Page 6: About The User Manuals
About the user manuals The operating instructions of the camera consist of 2 sets: this book and operating instructions (PDF). This book explains how to install the camera. Refer to the "Operating Instructions (PDF)" on the provided CD-ROM for descriptions of how to per- ®... -
Page 7: Table Of Contents
Contents Important safety instructions ...................... 3 Limitation of liability ........................4 Disclaimer of warranty ........................ 4 Preface ............................5 About the user manuals ......................6 Trademarks and registered trademarks..................6 Precautions ..........................8 Major operating controls and their functions ................9 Precautions for installation ...................... -
Page 8: Precautions
Precautions This product has no power switch. use a mild detergent and wipe gently. Then, Power is supplied from an external 12 V DC/ wipe off the remaining detergent with a dry 24 V AC (WV-CP504) or 220 to 240 V AC (WV- cloth. -
Page 9: Major Operating Controls And Their Functions
Major operating controls and their functions Side view (WV-CP500) ALC lens connector Side cover Tripod mount base Inside the side cover (Slide the cover leftward to the lock position.) (UP) Operation buttons* NEAR BF/MENU (LEFT) (SET) (RIGHT) * The following names are assigned to... - Page 10 Rear view (WV-CP500) External terminal Power indicator ALARM OUT POWER ALARM IN Video output connector VIDEO OUT 220 - 240V ~ 50Hz Power connector Rear view (WV-CP504) External terminal ALARM OUT Power indicator VIDEO OUT POWER ALARM IN (UP) Operation buttons*...
- Page 11 Side cover (only for WV-CP500) Power indicator When the operation buttons are used, the side This indicator lights up when the power is on. cover is slide leftward to the lock position. External terminal (☞ page 18) ALC lens connector...
-
Page 12: Precautions For Installation
+50 °C, and humidity below 90 %.The input er, a vending machine, or the like causes noise. power source is 12 V DC/24 V AC (WV-CP504) or 220 to 240 V AC (WV-CP500). Avoid connections during a lightning storm. - Page 13 Power cord (only for WV-CP500) Connect the power cord securely. Run the power cord so that no load is applied to the cord when panning or tilting the camera. (Failure to observe this may disconnect the power cord, and accordingly no image is dis-...
-
Page 14: Installation And Connection
Installation and connection Cautions: • ONLY CONNECT WV-CP504 TO 24 V AC OR 12 V DC CLASS 2 POWER SUPPLY. • Be sure to connect the grounding lead to the GND terminal. Rotate the lens (option) clockwise slowly to mount the lens. Important: • For use of C-mount lens, use the C-mount adaptor (option). • For prevention of damage to the camera body, use a lens with protrusion of 5.5 mm or less from the flange surface. - Page 15 Connect the lens cable to the ALC lens connector of the camera. ALC lens connector Pin No. Dump @ Dump ! Drive ! Drive @ Secure the camera mount bracket <Installation sample on a ceiling> (option) to an installation position, and mount the camera on the camera mount Camera mount bracket (option)
- Page 16 • The mounting conditions of the camera mount bracket are described as follows: Installation Applicable mount Recommended Number of Minimum pull-out place bracket screw screw strength (per 1 pc.) On ceiling WV-7011 4 pcs. 196 N WV-7010 3 pcs. 196 N WV-7012 3 pcs. 196 N On wall WV-831 4 pcs. 921 N WV-7013 3 pcs.
- Page 17 POWER ALARM IN To video input VIDEO OUT 220 - 240V ~ 50Hz WV-CP500 Use a cable tie (locally procured) to attach the coaxial cable to the camera mount bracket. Important: • The cable tie shall be made of metallic or durable material to be strong enough because the tie plays the role of camera drop prevention measures in case.
-
Page 18: External Synchronization Switch
(3 to 5 V DC, internally The external terminal is the same between pulled up) WV-CP500 and WV-CP504. Off: Open or 3 to 5 V DC On: Make contact with GND (required drive current: 0.2 mA or more) - Page 19 Turn on the power. WV-CP500 The included power cord is connected to this power connector. Connect between the power connector on the rear side of the camera and a plug socket with the supplied power cord. ALARM OUT POWER ALARM IN...
- Page 20 Adjust the camera angle by loosening the screw of the camera mount bracket while viewing the video monitor. Be sure to loosen the screw of the camera mount bracket when the camera angle is adjusted. If the camera angle is changed when the screw is tight, excessive force is applied to the cam- era mount bracket and camera, and accordingly they may be damaged.
- Page 21 (☞ the setup instructions (PDF) allows users to adjust the focus in both the near-infrared light and visible light regions (The variation in illuminance is not followed after focus adjustment.). • When a non-Panasonic lens that has an extended range for lens focusing is used, adjust the back focus after setting the focus to a position at a short distance from the FAR end. If adjust-...
-
Page 22: Setup Menu
Setup menu Performing each setting item in the setup menu should be completed in advance to use this unit. Perform the settings for each item in accordance with the conditions of the camera shooting area. Refer to the operating instructions (PDF) for further information. List of setup menu Setup item Description... - Page 23 Setup item Description SPECIAL CHROMA GAIN Adjusts the chroma level. AP GAIN Adjusts the aperture level. PEDESTAL Adjusts the pedestal (brightness) level. PIX OFF Corrects image defects such as flaws. COMMUNICATION Performs the communication setting of the system with a receiver into which this unit is integrated.
-
Page 24: Basic Operation
2 seconds simultaneously to call up the top Step 1 screen of the setup menu. Press the up button or the down button to move the cursor to "END". MODEL WV-CP500 SERIES CAMERA ID CAMERA Step 2 SYSTEM BACK-FOCUS Press the right button to move the cursor... - Page 25 Screenshot 3 The selected setup screen in the setup menu appears on the screen. Step 4 Perform the settings for each item. • Selection of setting item: **CAMERA SETUP** SCENE1 Press the up button or down button to ALC/ELC move the cursor. SHUTTER ON(HIGH) • Change of settings: SENS UP...
-
Page 26: Screen Transition Diagram
Screen transition diagram Top screen "CAMERA ID" screen MODEL WV-CP500 SERIES **CAMERA ID** CAMERA ID 0123456789 CAMERA ABCDEFGHIJKLM SYSTEM NOPQRSTUVWXYZ BACK-FOCUS ().,'":;&#!?= SPECIAL +- */%$ LANGUAGE SPACE POSI RET TOP END RESET ....SETUP ENABLE "CAMERA SETUP" screen **CAMERA SETUP**... -
Page 27: Troubleshooting
Troubleshooting Before asking for repairs, check the symptoms with the following table. Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below. Reference Symptom Cause/solution pages • Are the power cord and coaxial cable... - Page 28 Inspect the power cord, power plug and power connectors periodically. Reference Symptom Cause/solution pages Damaged power cord sheathing • The power cord, power connector, or power plug is damaged. Heated portion of power line Use of the damaged cord, connector, consisting of power cord, or plug may cause electric shock or –...
-
Page 29: Specifications
Alarm input, VMD enabling input, Color/BW switching input, Scene file switching input, Alarm output, Color/BW switching output Dimensions: WV-CP500: 75 (W) x 65 (H) x 132.5 (D) mm (Connectors and terminals excluded) WV-CP504: 72 (W) x 65 (H) x 103.5 (D) mm (Connectors and terminals excluded) WV-CP500: Approx. -
Page 30: Standard Accessories
CD-ROM* ............1 pc. Installation Guide (this book) ......1 pc. *The CD-ROM contains the operating instructions (PDF). The following parts are used during installation procedures. Power cord (only for WV-CP500) ..... 1 pc. Power cord plug (only for WV-CP504) ..... 1 pc. - Page 31 Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households) This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis.
- Page 32 Panasonic Corporation http://panasonic.net Importer's name and address to follow EU rules: Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15, 22525 Hamburg F.R.Germany © Panasonic System Networks Co., Ltd. 2010 Ns0409-2109 3TR005980CZA Printed in China...