Table of Contents
Advertisement
Quick Links
ADEMCO 6152RF Keypad / Transceiver – Installation and Setup Guide
Fixed Addressable Keypad/Transceivers for use with Honeywell Control Panels; incorporates normally-open
relay output with the functions of a 16 zone RF Receiver and a 5800 Transmitter module.
Programmable to support the
following :
- Bi-directional 5828/5828V
wireless keypads and wireless
keys (e.g., 5804BDV, 5834-4,
etc.)
- Up to eight button-type wireless
keys locally (programmed
directly into the keypad),
without occupying control panel
zones
- Up to 16 5800 series wireless
zones programmed into any
supported control panel
- Wireless keys with high security
mode enabled
To activate Function keys,
press and hold key for at
least 2 seconds; key pairs
are activated immediately.
Table 1 – Programmable
Function Keys
A or
and
B or
and
C or
and
D
Note: See the control's instructions for
details on programming the Function
keys for panic alarms or other special
functions (i.e., macros).
1. OPEN
2. WIRE
• Connect only one wire per terminal.
• For Daisy-Chain Configurations, use
wire splicing so only one wire is
connected to each terminal.
A
SEE Detail
Keypad
Front
Cover
Install Four (4)
Mounting Screws
ALARM
FIRE
Sounder
6152RF-KEYPAD-LBLD-07-19-13_1
Table 2 – Settings Key
Settings Key
Press
for 2 Seconds
Press
for 2 Seconds
and during the Display Test,
press and hold
for 3 Seconds
Wall
Surface
3. MOUNT
Mount on drywall, or in a single
or double-gang electrical box.
AWAY
NIGHT
NO
AC
PHONE
TEST
BYPASS
NOT READY
STAY
CHIME BAT
CHECK INSTANT CANCELED
Programmable Function Keys
Result
Enters Display Test Mode
Reboots the Keypad (the
keypad beeps and the ARM
and READY LEDs flash for
and
several seconds)
Control Panel
AUX
AUX
DATA
DATA
IN
OUT
[G] DATA OUT
[ ] GROUND
[+] +12VDC IN
[Y] DATA IN
16-24 AWG Only
6152RF: Fixed Word Display
2-Digit Zone Identifier
The '21' digits are used for specific
trouble indications. Refer to the
control panel instructions for details.
= System ARMED
= System NOT ARMED
= READY to Arm
= NOT READY to Arm
Arming Keys
Optional Front Cover Securing Screw
(Required in European Installations)
A
Detail
CONTROL PANEL
KEYPAD
TERMINAL STRIP
G
Green
Black
Red
Yellow
Y
NO
C
NC
RELAY OUTPUT
CONNECTIONS
Advertisement
Table of Contents
Related Manuals for Honeywell ADEMCO 6152RF
Summary of Contents for Honeywell ADEMCO 6152RF
- Page 1 ADEMCO 6152RF Keypad / Transceiver – Installation and Setup Guide Fixed Addressable Keypad/Transceivers for use with Honeywell Control Panels; incorporates normally-open relay output with the functions of a 16 zone RF Receiver and a 5800 Transmitter module. Programmable to support the...
- Page 2 INSTALLATION AND APPLICATION GUIDELINES For installation, consider the following: • The keypad provides an on-board relay, programmed in the • Locate the 6152RF in an area and at a height convenient for keypad and operated by wireless key (see Wireless Key On- user operation.
- Page 3 Table 6 – Programming Options After editing any programming address, pressing will save the displayed information and return to the Start screen. Enter Moves to Address Program Display Choices Default Notes Description Address Enable keypad address in the Enter [1] Keypad Address 00-31 Control panel.
- Page 4 PROGRAMMING LOCAL WIRELESS KEYS This section is for first time enrolling and setup of wireless keys. To edit or delete a wireless key that is already enrolled; refer to the, Deleting, Replacing or Editing Wireless Keys section. Table 7 – Wireless Keys Programming Step Action Display...
- Page 5 Table 7 – Wireless Keys Programming (continued) Step Action Display Wireless Key Function Chart (continued) Default Loop Functions (continued) # + 7 + n (VISTA-10P, VISTA-15P, (Cont’d) LOOP 2 Manually Start a Relay Action VISTA-20P, VISTA-21ip) Disarm # + 8 + n (VISTA-10P, VISTA-15P, Manually Stop a Relay Action VISTA-20P, VISTA-21ip) LOOP 3...
- Page 6 Table 8 – Deleting, Replacing or Editing Wireless Keys (continued) Step Action Display Edit To change any of the programming for the wireless key, refer to Alternately flashes "d" with the device number; the procedures described in Table 7 for the following changes:. and "-."...
- Page 7 FEDERAL COMMUNICATIONS COMMISSION STATEMENT: INDUSTRY CANADA CLASS B STATEMENT The user shall not make any changes or modifications to the equipment unless authorized by the This Class B digital apparatus complies with Canadian ICES-003. Installation Instructions or User Manual. Unauthorized changes or modifications could void the Cet appareil numérique de la classe B est conforme à...
- Page 8 REFER TO INSTALLATION INSTRUCTIONS FOR THE CONTROL PANEL WITH WHICH THIS DEVICE IS USED FOR WARRANTY INFORMATION AND LIMITATIONS OF THE ENTIRE ALARM SYSTEM. WARRANTY INFORMATION: For the latest warranty information, please go to www.honeywell.com/security/hsc/resources/wa DOCUMENTATION AND ONLINE SUPPORT: For the latest documentation and online support information, please go to: http://www.security.honeywell.com/hsc/resources/MyWebTech...