Bosch ICP-AMAX4-P1 Installation Manual
Amax panel 4000; amax panel 4000 en
Hide thumbs
Also See for ICP-AMAX4-P1:
- Quick start manual (72 pages) ,
- Installation manual (176 pages)
Related Manuals for Bosch ICP-AMAX4-P1
Summary of Contents for Bosch ICP-AMAX4-P1
- Page 1 AMAX panel 4000 / AMAX panel 4000 EN ICP-AMAX4-P1 / ICP-AMAX4-P2-EN / ICP-AMAX-P3-EN Installation Guide...
-
Page 3: Table Of Contents
AMAX panel 4000 / AMAX panel 4000 Table of Contents | en Table of contents Graphics Safety Short Information System overview Optional Modules and Peripheral Devices Bosch Option Bus Keypad 5.2.1 General 5.2.2 Address Setting 5.2.3 Wiring 5.2.4 Status Indicator DX2010 5.3.1... - Page 4 Address and Key Programming 7.8.1 Address Programming 7.8.2 Programming with the ICP-EZPK Programming Key Configuration Programming with the Keypad 8.1.1 Text Keypad Menu Programming 8.1.2 LED/LCD Keypad Programming PC Programming 8.2.1 Direct Connection 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 5 Communication and Reports Setting Zone Programming Output Programming Access Codes System Programming Troubleshooting 10.1 General Trouble 10.2 Trouble Fault Inquiry Maintenance 11.1 Firmware Upgrade with the ICP-EZRU2 Upgrade Key Technical Data Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
-
Page 6: Graphics
100 Ω - 2,2 k RFRC-OPT 1= (1) Slow flash: Normal state On: Trouble state Off: Trouble state PO-5 1 Tamper Switch 2 Zone Switch 3 EOL 2,2 k Figure 1.1: AMAX 4000 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... -
Page 7: Amax Panel 4000 / Amax Panel 4000 Graphics | En
Adr. 134(6) / 250(9) RF Receiver: RF3227E 230V ~50Hz RFRC-OPT 1= (1) 85mA Fuse 500 mA 1 Tamper Switch 2 Zone Switch 3 EOL 2,2 k Figure 1.2: AMAX 2100/3000 Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... -
Page 8: Safety
- The system / product must be installed and maintained by qualified installer / service person. - Bosch recommends testing the alarm system at least once a week. Danger! As static-sensitive components are included in PCBs, anti-static steps should be followed and they should be carefully installed. -
Page 9: Short Information
Each AMAX panel can be tailored to meet your requirements quickly and easily. The programming simplicity makes your installation quick, accurate, and rewarding. Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... -
Page 10: System Overview
Figure 4.1: AMAX 2100/3000 Overview Radion LCD / LED Keypad Text Keypad DX2010 Option Bus B426 DX4020G DX3010 PSTN GSM/ GPRS Video A Link Plus Figure 4.2: AMAX 4000 Overview 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... -
Page 11: Optional Modules And Peripheral Devices
The AMAX panel provides the Bosch Option Bus to attach expansion modules. AMAX 2100 / 3000 each has one (Bosch Option Bus 1) and AMAX 4000 has two (Bosch Option Bus 1 and Maximum 14 modules (8 keypads) can be connected to each bus. The total length of the cable for connection of all keypads and expansion modules wired to one Bosch Option Bus must not exceed 700m. -
Page 12: Keypad
6-position DIP switch. The address of each keypad is unique. DIP Switch Keypad Address Table 5.2: Keypad Address Settings * AMAX4000 ** AMAX3000/4000 Figure 5.1: 6-Position DIP Switch 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... -
Page 13: Wiring
Jumper short-circuited (both metal pins are covered) Table 5.3: Keypad Jumper Settings 5.2.3 Wiring Connect the keypad to Bosch Option Bus of AMAX panel according to the following figure. The last keypad must be placed within a cable distance of 200m. AMAX 2100 / 3000 Keypad AMAX 4000 Figure 5.2: Connecting keypad to the AMAX Panel... -
Page 14: Address Setting
When data bus address is changed, the module needs to be re-powered to make the new address effective. 5.3.3 Wiring Do not use twisted pair or shielded cables to connect DX2010 and the AMAX panel. 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... -
Page 15: Status Indicator
For more information about installation, see DX3010 Installation Guide. See also – Module Installation, page 23 5.4.2 Address Setting Each DX3010 module connected to the AMAX panel must have its own data bus address. Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... -
Page 16: Wiring
External Power Supply 305m 610m Table 5.9: Lengths of cable for DX3010 AMAX 2100 / 3000 DX3010 DX3010 AMAX 4000 Figure 5.6: Connecting DX3010 to the AMAX Panel 5.4.4 Status Indicator None. 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... -
Page 17: B426
9, i.e., set the address to 250 when the second B426 is used. 5.5.3 Wiring Connect B426 to Bosch option Bus 1 or 2. The cable may not exceed 150 meters. AMAX 2100 / 3000 B426 AMAX 4000 Figure 5.7: Connecting B426 to the AMAX Panel... -
Page 18: Dx4020-G
The connection of ITS-DX4020-G and the AMAX panel is divided into two modes: GPRS and GSM. AMAX 2100 / 3000 DX4020G AMAX 4000 Figure 5.8: GPRS Mode in Support of IP 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... -
Page 19: Status Indicator
Reception distances are generally improved with higher mounting locations and with no metal objects near the antennas. 5.7.2 Address Setting Set receiver address to #1. The AMAX panel supports only receiver 1, not receiver 2. Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... -
Page 20: Wiring
Figure 5.10: Address 5.7.3 Wiring Connect the RF3227E receiver to Bosch option Bus. The cable must not exceed 300 m. Adding additional devices to the bus might reduce the maximum distance. Shielded cable is not required. Do not use twisted pair wires. -
Page 21: Status Indicator
Address Setting Set rotary switch to value 1. The AMAX panel supports one receiver only. 5.8.3 Wiring Connect the RADION receiver to bosch option bus. The cable distance to the AMAX panel may not exceed 300 meters. 5.8.4 Status Indicator... - Page 22 – A communication failure between the AMAX panel and the of the 3rd pulse receiver or – An invalid address switch setting. Table 5.13: RFRC-OPT Radion Receiver System Status Indicator 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
-
Page 23: Installation
Please choose appropriate positioning screw kit when you have to install in a non-load bearing wall. E N √ E N √ Enclosure - Standard Enclosure with mounting plate Figure 6.1: Enclosure / with mounting plate Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... -
Page 24: Battery Installation
Connect one end of the red wire to the "BATT +" port of the AMAX panel, the other end to the positive (+) pole of the battery. Once the installation is complete, the AMAX panel will begin to charge the battery. 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... -
Page 25: System Power Up
The AMAX panel indicates the system status by using the LED status indicator on the system main board. Slow flash of red on status indicator (repeating on and off with an interval of 1 second) indicates normal system operation. Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... -
Page 26: Prerequisites For Certification Conform Installation
To realize EN conform Access to the Monitored Area, one of the following methods must be used – Opening a door (to the entry / exit route) must start the entry procedure – Indication of arm / disarm Status 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... - Page 27 When the panel is set without EN parameters, the EN Indication (on Label) must be removed – Maximum of 10 Devices shall be connected to one Zone Input (Panel, Keypad, Input Module, RFUN,…) Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
-
Page 28: Nfa2P Afnor / Cnpp - Amax 4000
O ption 3: G rade 2 (European EN standards) + RTC Certification Number: 1223400001A0 Prerequisites for an NFa2p conform Installation - When aNFa2p conform instalation is made, the environmental class of the Panel is "1” 6.5.3 INCERT - AMAX 4000 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... -
Page 29: Sff - Amax 2100 / 3000 / 4000
VDS Schadenverhütung SSF Stöldskyddsföreningen Amsterdamer Str.172 Tegeluddsvägen 100 50735 Köln 115 87 Stockholm www.vds.de http://www.stoldskyddsfpreningen.se T he Panel com plies with the Following Standards: SSF 1014 Edition 4 Alarm class 1 Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... -
Page 30: Settings
Example You can set up Dialer 1 to report to receiver 1 in Bosch Network (Conettix) Format and set up Dialer 2, Dialer 3, and Dialer 4 to report to a receiver of a central monitoring station in Contact ID Format only, if Dialer 1 is unsuccessful. - Page 31 If Contact ID or SIA format is selected, the information is transmitted by telephone line; if Bosch Network is selected, then it is connected with B426 / DX4020 or ITS-DX4020G GPRS. Transmission format is defaulted as Contact ID.
- Page 32 AMAX panel supports SIA Format. SIA allows transmitting System ID, event code, zone ID, area ID, event time, and also event text. Conettix IP Format AMAX panel supports Conettix IP. AMAX panel with DX4020G and B426 are able to connect to Bosch Receivers 6600/6100 using Conettix IP Format. Event Description Dialer Event...
- Page 33 3351 √ √ PANIC 24-HOUR 1120 √ √ √ PANIC 24-HOUR RESTORE 3120 √ FIRE 24-HOUR 1110 √ √ √ FIRE 24-HOUR RESTORE 3110 √ OUTPUT FAULT 1320 √ √ Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 34 1341 √ RF RECEIVER TAMPER RESTORE 3341 √ RF RECEIVER FAULT 1333 √ RF RECEIVER FAULT RESTORE 3333 √ RF RECEIVER JAM 1344 √ RF RECEIVER JAM RESTORE 3344 √ 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 35 When no callback from the receiver after the acknowledge time is reached, the AMAX panel takes it as an unsuccessful communication and makes another attempt. The time ranges from 5 to 99 sec. Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
-
Page 36: Reports
Display of faults When multiple reports are queued for delivery, the communication path fault is displayed as a logic or relationship. Example: 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... - Page 37 When the failed (internal) delay zone, (internal) instant zone and (internal) follow zone are disarmed, the fault recovery event will occur even if the zone is still in triggering status Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 38 – Keypad Fault: When fault occurs between the keypad and the AMAX panel, the report will be sent. After the fault is recovered, the recovery report will be sent 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 39 Keypad Fire Alarm Reporting If you press and hold both 4 and 6 for 3 seconds, the fire alarm report will be sent. The fire alarm report has no corresponding alarm recovery report. Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
-
Page 40: Automatic Test Report
Only when IP module 1 is used and set to paths 1 to 4, the report can be sent to those paths. 7.1.5 Remote Access The AMAX panel supports remote programming via USB, telephone or IP network using software A -Link Plus. – uploading / downloading programming parameters 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... -
Page 41: Remote Pc
The user presses [#] between two acknowledgement tones to confirm the alarming. The acknowledgement tone is the DTMF signal sent by the remote user with the [#]. Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... -
Page 42: Ring Times
The installer commands can be used only when all areas of the system are in disarming status with no alarm activated and when installer access is enabled from user. 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... - Page 43 C o p y p ro g r. ke y d a ta to co n tro l p a n e l. [9 ][6 ][3 ] + [# ] √ D is p la y FW ve rs io n [9 ][9 ][9 ] + [# ] √ Figure 7.1: User Code Commands Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 44 User Type Master User Super User Basic User Arming User Duress User 05 -15 No Priority User Code in Area User codes are assigned to one or more areas. Value Area 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 45 AMAX panel 4000 / AMAX panel 4000 Settings | en Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
-
Page 46: Installer Code
Report = 0 User 1 - 64 Report = 1 - 64 Keyfob 1 – 128 Report = 65 - 192 A-Link Report = 251 Phone arm / disarm Report = 252 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... -
Page 47: Code Permissions
Instant Interior instant Delay Interior delay Follower Interior follower 24-hour Key-switch toggle Key switch on / off 24-hour panic 24-hour fire 24-hour fire with verification* Tamper Bolt contact External fault Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... - Page 48 – When system is disarmed and zone is not restored before, a zone fault restore report is sent 03 - Delay The delay zone will perform as below: 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 49 07 - 24 Hour The 24 - hour zone will perform as below: Disarm: – Zone normal - no alarm / no report – Zone triggered - alarm / report Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 50 Wiring Diagram for key-switch Zone: short for arm. The momentary time is capable of lasting Minimum 300ms. Zone Wiring Diagram for key-switch Zone: open for arm. The momentary time is capable of lasting Minimum 300ms. Zone 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 51 AWAY Arm: same as disarm performance STAY Arm: same as disarm performance 14 - Bolt Contact The Bolt-Contact zone will perform as below: Disarm: Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 52 AWAY Arm: same as the delay exit zone AWAY arm status STAY Arm: – This zone will be Ignored and performed as disarm – Refer to Keypad Indicators to see how the zone is displayed during exit time 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 53 9 – digit RFID using pin keys. When AUTO is selected, trigger RF device in order to enter RFID automatically. Hardwired Input Zones On-board Inputs: The AMAX panel provides onboard hard-wired inputs. An additional input is provided for the enclosure tamper. Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 54 2200 2750 normal 2970 4400 4950 triggered 5220 ∞ tamper Using one 2.2 Kilo resistor as EOL of the tamper zone, which works together with the zone EOL 2.2 Kilo. 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
-
Page 55: Pulse Count Duration
Force arm Bypass Silent alarm / Chime Disabled mode Silent alarm Chime mode Zone pulse count Disabled 1-9 pulses Zone lockout Disabled 1 times alarm lockout 3 times alarm lockout Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... - Page 56 The zone bypass is valid in one arming period only and will be resumed after disarming. Before disarming, the bypassed zones will ignore all zone triggering and restoration events. The key switch zone cannot be bypassed. 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 57 The system supports the tamper detection of the zone. This function ensures that the zone is in normal operating status. The process is as follows: If 24-hour zone tamper is enabled, the wiring method for two-terminal resistor is required. Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 58 When the first zone or one of the other zones (with cross zone option) is / are triggered twice or more after cross zone time is expired, the timer restarts 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
-
Page 59: Zone Indication Keypad And Event Log
AMAX 2100: In a one area system keypad zone number 17 should be indicated on an 8 zone LED keypad. After disabling zone 5 zone number 17 is indicated on keypad as number 5. Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... -
Page 60: Keypads And Areas
8 zones and cannot display other zones, but can report zone events. For IUI- AMAX3LED16 keypad, each area can display up to 16 zones and cannot display other zones, but can report zone events. Keypad IUI -AMAX4-TEXT can display up to 64 zones. 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... -
Page 61: Area Timing
When the command [2] [1] is used for fault inquiry, the keypad can be programmed to sound prompt tone to indicate new system fault. The system is defaulted to enable. In case of a new fault, all keypads will sound a short beep once a minute. Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... - Page 62 Enclosure Tamper Timing The AMAX panel supports different reaction times for the onboard tamper used for panel enclosure. The reaction time is default 400 ms and can be changed to 150 ms. 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
-
Page 63: System View
If the default pads are short-circuited for over 10 seconds after power-up, the AMAX panel will discard resetting to factory default. 7.5.2 System View Fault Analysis AMAX panel can display eight categories of 41 kinds of system failure. Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... - Page 64 1 - 2 Panel Aux Power 1 - 2 Fault Bosch Option Bus Power Failure 1 - 2 Bosch Option Bus 1 - 2 Power Fault RF Repeater AC Power Failure 1 - 8 RF Repeater 1-8 AC Power Fault...
- Page 65 1 - 8 RF Repeater Tamper External Failure 1 - 16 External Fault Zone 1-16 For more information about fault inquiry, see Trouble Fault Inquiry, page 140. FW Version AMAX keypad displays Firmware Version. Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
-
Page 66: Outputs And Sirens
– Zone (alarm or tamper) programmed to disable zone silent alarm – System tamper / DX2010 tamper / keypad tamper – Keypad alarm (emergency alarm, fire alarm, medical aid alarm) 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... - Page 67 When Programming mode is entered = one pulse activation (1sec) (enabled / disable option) 8 - Internal Siren with tamper The output is triggered when internal siren with tamper. Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 68 The output is reset when the output programmed duration is up. lf this duration is programmed as 000, the output will continue till the tamper condition is restored and tamper is reset. 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 69 The output is triggered when Keyfob Button 3 is pressed. 23 - RF Keyfob button 4 The output is triggered when Keyfob Button 4 is pressed. 24 - Chime Indication Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 70 The output is triggered when Bypassed Zone. 29 - Ready to Arm The output is triggered when ready to arm. 30 – Walk Test Output Mode The output is triggered when Walk Test Output Mode. 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 71 RF keyfob button 4 (light) Chime indication *1 Verified alarm Unverified alarm Technical alarm Bypassed zone Ready to arm 0 = All areas 1 - 16 = Areas 1 - 16* Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
-
Page 72: Sirens
Silence Warning Device When Disarmed Enables / disables silence warning device when disarmed or by pressing any key. RF Devices 7.7.1 RF Options RF Receiver Functionality Enables or disables RF receiver functionality. 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... -
Page 73: Rf Devices / User
/ noise ratio distance. In dependency of the rating, AMAX panel provides an estimation of GOOD or RELOCATE. Clear RF devices The AMAX panel provides the option to clear all RF devices in a step. Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... -
Page 74: Address And Key Programming
Connect the programming key to the plug on top of the printed circuit board (PCB) of the AMAX panel. Please note that the direction of the programming key should be consistent with the direction marked on the PCB. 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... - Page 75 Unplug the programming key from the AMAX panel. LED / Icon LCD keypad can also be used to copy key parameters to the AMAX panel. For more information refer to Command 963 . Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
-
Page 76: Configuration
Select [Save and Exit] and press [#] to save system programming data, exit menu programming, and reset system. Warning! Programming parameters must be set within the range of the programming address. Otherwise, the system will turn to an indeterminate status. 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... - Page 77 = Call the control panel and allow the phone to ring no more than four times and then hang up. If you call again within 45 sec, the control panel answers the call on the first ring. Figure 8.1: Com+Report Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 78 CODE LENGTH: 4 - 6 4 - 6 CODE PERMISSIONS TAMPER RESET USER 0 = disabled 1 = enabled ARM/DISARM INSTAL. 0 = disabled 1 = enabled Figure 8.2: Code Setting 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
-
Page 79: Zone Type
06 = Destination 1 (2, 3 and 4 for backup) ZONE DOMESTIC CALL 03 = Destination 3 07 = Destin. 1 (2 for backup) and Destin. 3 (4 for backup) Figure 8.3: Zone Setting Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... - Page 80 KP TONE / LOCKOUT KEYPAD ALARM TONE 0 = disabled 1 = enabled KEYPAD LOCK COUNT 0 = disabled 1 - 15 times EN=10 [10] Figure 8.4: KP Area Setting 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 81 0 = 400 ms 1 = 150 ms IN=1 FACTORY DEFAULT DEFAULT PANEL YES DEFAULT PANEL NO SYSTEM VIEW FAULT ANALYSIS FW VERSION FW Version is displayed: AMAX4000P3-1.02 Figure 8.5: System Setting Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
-
Page 82: Output Settings
0 = disabled 1 = enabled INT SIREN INDIC ON 0 = disabled 1 = enabled SIREN OFF ANY KEY 0 = disabled 1 = enabled Figure 8.6: Output setting 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... - Page 83 MANUAL and AUTO. MANUAL Type 9-digit value for RFID. Press # to confirm. AUTO Press Keyfob button and wait until KEYFOB ID is displayed by the system. Press # to confirm. Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
-
Page 84: Led/Lcd Keypad Programming
Entering [9] [5] [9] + [#] means not to save the programming data. For LED / Icon LCD keypad, the programming data is displayed by the keypad indicator. See Programming Data Indicators. Programming Data Indicators Data Zone Indicators Value Mains 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... -
Page 85: Pc Programming
“installer code” is the same as currently programmed in the AMAX panel. The value is 1234, when firmware of the AMAX panel was upgraded or the AMAX panel has factory settings. Refer to , page 87 Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... -
Page 86: Direct Connection
AMAX panel via USB cable. Plug cable into USB port of AMAX panel and connect the other side of this cable to an USB port of the PC running A-Link Plus software. 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... - Page 87 Configuration | en Install USB driver. The device driver is located in A-Link plus application path (example: C\ \program files (x86)\Bosch Security System\A-Link Plus\USB_DRIVER).This installation will create an additional COM device on the PC. When finished installation, identify the COM-Port associated to this device.
-
Page 88: Modem Connection
Run RPS on the remote PC and set relevant parameters in relevant operating interfaces. – Go to “File” and click “Communication Settings” to set parameters related to modem in the communication Settings tab page, then click “Save” 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... - Page 89 “Customer Information” tab page. The “Customer Number” must be entered. Enter the telephone number connected to the AMAX panel in “AMAX Panel Telephone Number”. The AMAX panel telephone number does not need to be set for manual connection. Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 90 Or manual dialing connection: Select “Modem Connect” in the “Link” tab page and click “Wait for Incoming Call”, then initiate callback call from the AMAX panel with keypad: Enter SUBSCRIBER NUMBER, press [5] [7], and then [#]. 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
-
Page 91: Ip Connection
(addresses 0162 - 0179), i.e., enter IP address, port number of RPS, and DHCP update time on the AMAX panel. Run RPS on the remote PC and set relevant parameters in relevant operating interfaces. Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... - Page 92 The prompt information will recommend the SUBSCRIBER NUMBER, the AMAX panel received the last time IP address and port number.. Under DHCP environment, it is not necessary to set “AMAX Panel IP Address” and “AMAX Panel Port Number”. 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 93 Or manual IP connection: Select “Network Connection” and click “Wait for Incoming Call” in the “Link” tab page. Then initiate IP connection from the AMAX panel with keypad: Enter SUBSCRIBER NUMBER, press [5] [7], and then [#]. Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 94 AMAX panel parameters, remote arming/disarming, viewing log, and so on. After IP successfully connected, RPS will disconnect it with the AMAX panel after 5 minutes of idling if you select “Auto disconnect when idle connection exceeds 5 minutes” option. 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
-
Page 95: Address Programming
Network polling time for receiver (001 - 999 minutes ) 0087 - 089 Telephone number / IP address and port for receiver 4 0090 - 0106 Subscriber ID number (0 – 9, B – F) 0107 - 0112 000000 Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... - Page 96 ITS-DX4020-G module or B426- module 1 B426 module 2 System Reporting Option Address Default Zone status restore report 0121 AWAY arming / disarming report 0122 EN=1/5/6/7 STAY arming / disarming report 0123 EN=1/5/6/7 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 97 Address Default 0 = disabled, 1 = enabled 0138 VDS-A=1 Force Arm When System Is In Trouble Condition Address 0139 Address Default 0 = disabled, 1 = enabled VDS-A EN=0 Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 98 Remote Programming Address 0145 Address Default 0 = disabled, 1 = enabled 0145 VDS-A=0 Callback Telephone Number Address 0146 - 0161 Address Default See Telephone Programming Parameters 0146 - 0161 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 99 This function is only accessible in address programming Onboard Tamper Reaction Time Address 0185 Address Default 0 = 400 ms, 1 = 150 ms 0185 1=Incert – This function is only accessible in address programming Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 100 Battery Check Interval Address 0204 Address Default 0 = disabled , 1-15 minutes 0204 VDS-A EN=15 Cross Zone Timer Address 0205 - 0207 Address Default 001 - 999 sec 0205 - 0207 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
-
Page 101: Zone Programming
Address 0210 - 0361 Zone function # 00 Address Default Zone type 0210 - 0211 Force arm / zone bypass 0212 VDS-A EN=0/2 Silent alarm / chime mode 0213 VDS-A EN=0/2 Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... - Page 102 0242 VDS-A EN=0/2 Silent alarm / chime mode 0243 VDS-A EN=0/2 Zone pulse count 0244 VDS-A EN=0 Zone lockout 0245 Zone tamper (DEOL) 0246 Zone status report 0247 VDS-A EN=1/5/6/7 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 103 0276 Zone status report 0277 VDS-A EN=1/5/6/7 Unverified alarm report / cross zone 0278 VDS-A EN=0 Domestic number 0279 Zone function # 07 Address Default Zone type 0280 - 0281 Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 104 Zone type 0310 - 0311 Force arm / zone bypass 0312 VDS-A EN=0/2 Silent alarm / chime mode 0313 VDS-A EN=0/2 Zone pulse count 0314 VDS-A EN=0 Zone lockout 0315 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 105 Zone pulse count 0344 VDS-A EN=0 Zone lockout 0345 Zone tamper (DEOL) 0346 Zone status report 0347 VDS-A EN=1/5/6/7 Unverified alarm report / cross zone 0348 VDS-A EN=0 Domestic number 0349 Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 106 For the range of each zone function option, see zone function options below. Zone Function Options Zone function option Description Zone type Zone not used Instant Interior instant Delay Interior delay Follower Interior follower 24-hour Key-switch toggle Key switch on / off 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 107 1 time alarm lockout 3 times alarm lockout 6 times alarm lockout Alarm duration Zone Tamper (DEOL) Disabled Enabled Zone Status Report No report required Receiver 1 Receiver 2 Receiver 3 Receiver 4 Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 108 11 = Follow partition 2-12** 12 = Follow partition 2-13** 13 = Follow partition 2-14** 14 = Follow partition 2-15** 15 = Follow partition 2-16** * AMAX 3000/4000 ** AMAX 4000 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 109 * AMAX 4000 supports up to 64 zones, 16 keypads, and 16 areas AMAX 3000 supports up to 32 zones, 8 keypads, and 8 areas AMAX 2100 supports up to 8 zones, 4 keypads, and 2 areas *** AMAX 3000 / 4000 Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 110 0712 - 0713 0823 0887 0714 - 0715 0824 0888 0716 - 0717 0825 0889 0718 - 0719 0826 0890 0720 - 0721 0827 0891 0722 - 0723 0828 0892 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 111 ** refer to Table DX2010 modules *** AMAX 3000 / 4000 ***** Zones 17 to 32 are dedicated to Keypad 1 to 16 (zone 17 = keypad 1, zone 32 = keypad Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 112 0774 - 0775 0854 0918 0776 - 0777 0855 0919 0778 - 0779 0856 0920 0780 - 0781 0857 0921 0782 - 0783 0858 0922 0784 - 0785 0859 0923 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 113 ** refer to Table DX2010 modules **** AMAX4000 DX2010 module address Dedicated zone 9 - 16 17 - 24 25 - 32 33 - 40 41 - 48 49 - 56 57 - 64 Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
-
Page 114: Output Programming
VDS-A EN=0 Output time 0539 - 0541 VDS-A EN=180 * AMAX 4000 Notice! When the zone activating alarm is programmed as a silent alarm, keypad and audible alarm have no output. 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... - Page 115 RF Keyfob button 3 (Garage Door) 0 = Any area, 1 - 16 = Areas 1 – 16* RF Keyfob button 4 (light) Chime indication *1 Verified alarm Unverified alarm Technical alarm Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 116 Output area / zone 0550 - 0551 Output mode 0552 - 0553 Output time 0554 Output 7 0555 - 0557 Output event type Address Default Output area / zone 0558 - 0559 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 117 Address 0542 - 0605 0603 - 0605 DX3010 2 Output Programming* Address 0606 - 0669 Output 13 Address Default Output event type 0606 - 0607 Output area / zone 0608 - 0609 Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 118 Output event type 0654 - 0655 Output area / zone 0656 - 0657 Output mode 0658 Output time 0659 - 0661 Output 20 Address Default Output event type 0662 - 0663 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
-
Page 119: Access Codes
Default: 15 1022 - 1027 1020 = 1 1028 1029 - 1030 1031 - 1036 Value range: 1021 = 5 1037 1038 - 1039 1040 - 1045 0 = master code Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... - Page 120 1310 - 1315 1316 1317 - 1318 1319 - 1324 1325 1326 - 1327 1328 - 1333 1334 1335 - 1336 1337 - 1342 1343 1344 - 1345 1346 - 1351 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
-
Page 121: System Programming
Entry and Exit Delay Area Exit Delay Default Entry Delay Default Address Address 403 - 405 406 - 408 409 - 411 412 - 414 3 ** 415 - 417 418 - 420 Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... - Page 122 481 - 483 484 - 486 15 * 487 - 489 490 - 492 16 * 493 - 495 496 - 498 000-999 seconds 000-999 seconds EN=045 seconds * AMAX4000 ** AMAX3000/4000 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 123 / disarming, bypass, and alarm reset operations can be performed on the master keypad. Operations can be performed in the area only if the master keypad is switched to the corresponding area. Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 124 Address 0943 Address Default 0-15 0 = most sensitive 0943 RF Device Low Level Battery Resound Address 0944 Address Default 0 = disable 1 = 4h 2 = 24h 0944 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 125 Default 0 = disable 1 = Enable 0945 RF Keyfob Panic Option Address 0946 Address Default 0 = No alarm 1 = Silent alarm 2 = Non silent alarm 0946 Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 126 1970 – 1978 2290 – 2298 1980 – 1988 2300 – 2308 1990 – 1998 2310 – 2318 2000 – 2008 2320 – 2328 2010 – 2018 2330 – 2338 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 127 Wireless Repeater RF ID Repeater Address Default 2340 – 2348 2350 – 2358 2360 – 2368 2370 – 2378 2380 – 2388 2390 – 2398 2400 – 2408 2410 - 2418 Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 128 2690 – 2698 3010 – 3018 2700 – 2708 3020 – 3028 2710 – 2718 3030 – 3038 2720 – 2728 3040 – 3048 2730 – 2738 3050 – 3058 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 129 3330 – 3338 3650 – 3658 3340 – 3348 3660 – 3668 3350 – 3358 3670 – 3678 3360 – 3368 3680 – 3688 3370 – 3378 3690 – 3698 Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 130 75 - 92 16 - 18 93 - 110 19 – 21 111 - 128 22 - 24 1 – 16 1 – 3 17 – 32 4 – 6 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 131 37 – 48 9 – 10 49 – 60 11 – 12 61 – 72 13 – 14 73 – 84 15 – 16 85 – 95 17 – 18 Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 132 1 – 10 1 - 2 11 - 20 3 - 4 21 – 29 5 – 6 30 – 38 7 - 8 39 – 47 9 – 10 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 133 7 – 8 33 – 40 9 - 10 41 - 48 11 - 12 49 - 56 13 - 14 57 - 64 15 - 16 65 - 72 Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 134 å æ ç è é ê ë ì í î ï ð ñ ò ó ô ô ö ÷ ø ù ú û ü ý þ ÿ Table 9.5: Characters 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 135 4528 - 4563 4564 - 4599 4600 - 4635 4636 - 4671 4672 - 4707 4708 - 4743 4744 - 4779 4780 - 4815 4816 - 4851 4852 - 4887 Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 136 5716 - 5751 5752 - 5787 5788 - 5823 5824 - 5859 5860 - 5895 5896 - 5931 5932 - 5967 5968 - 6003 6004 - 6039 Table 9.6: Assign Zone Names 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 137 Zone name may have up to 18 characters. Each character of the zone name uses 2 addresses. Example: A = 4 1, A = Address 3736 = 4, Address 3737 = 1 Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
-
Page 138: Troubleshooting
The tamper switch is not circuit jumper connected – Connect modules for – External module should programming such as be used for DX2010, DX3010, B426, programming, but it not or ITS-DX4020-G actually connected 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... - Page 139 0144 to a number from 1 address 0144 is set to 0) to 15 – There are multiple areas – The telephone arming is in the system available when the system has area 1 only Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
-
Page 140: Trouble Fault Inquiry
When the fault is reset, send the restored report to the configured destinations. The FAULT indicator is turned off, when there is no other system fault. – Output Expansion Module Failure Condition: No communication with DX3010 if DX3010 is programmed. Restore: 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... - Page 141 The printer and DX4010 are normal and fault is reset. Supervise: Report the printer error to configured destination when the fault is detected. Slow flash FAULT indicator (refer to Keypad Indicators the detailed description). Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 142 Supervise: Report the wireless zone missing fault to configured destination when the fault is detected. Slow flash FAULT indicator (refer to Keypad Indicators for the detailed description). 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 143 Slow flash FAULT indicator (refer to Keypad Indicators for the detailed description). When the fault is reset, the FAULT indicator is turned off when there is no other system fault. Configuration Conflict Keyfobs Condition: Any one keyfob configuration is error. Restore: Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 144 Monitor the voltage by MPU. Report the AUX power fault to the configured destination programmed on address 124. Slow flash FAULT indicator (refer to Keypad Indicators for the detailed description). 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 145 Voltage is raised to 12V and fault is reset. Supervise: Monitor the voltage by MPU. Report the Bosch Option Bus Power Supply fault to the configured destination programmed on address 124. Slow flash FAULT indicator (refer to Keypad Indicators for the detailed description).
- Page 146 The FAULT indicator is turned off when there is no other system fault. 5- System Failure – Date and Time not set Condition: Date and time is not set after the system is powered on. Restore: 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 147 When the Tamper Condition is reset, send the restored report to the configured destinations. The FAULT indicator is turned off when there is no other system fault. Zone Expansion Module Tamper Zone expansion module 1 to 6 tamper Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 148 Report the keypad lock out to configured destination on address 124 when the keypad lock out is detected. Slow flash FAULT indicator (refer the detailed description in chapter keypad indicators). 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 149 When the fault is reset, send the restored report to the configured destinations. The FAULT indicator is turned off when there is no other system fault. External Fault Zone The zone indicator 8 lights to indicate external fault conditions. Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
-
Page 150: Maintenance
Power ON AMAX panel. Observe LED of upgrade key flickers during upgrade is sent to AMAX panel. This takes about one minute. When upgrade is terminated, LED blinks slowly. Remove upgrade key 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH... -
Page 151: Technical Data
Events: 256 history events, stamped with time, and date 256EN history events, stamped with time, and date 256 dialer history events, stamped with time, and date Pin Code 1000000 variations: Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112... - Page 152 1000mA (recharge Batt 80% in 24h) = 400mA Aux 1 / 2 (+12V/ – Nominal Output Voltage under AC line input: 13,8 VDC +3% / -5% GND) Output: – Vpp (max) 675mV 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 153 10.8VDC - 13.8VDC range: Current standby 31mA Consumption: max 100mA Ingress protection IP 30 rating: Security level: IK 06 Certification: Europe EN 50130-4 (6/2011) EN 55022 (5/2008) EN 60950-1:2006 + A11:2009 Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 154 EN type: EN = B, IK = 06, IP = 30 Certification: Europe EN 50130-4 (6/2011) EN 55022 (5/2008) EN 60950-1:2006 + A11:2009 EN 50131-3 grade 2 Environmental Class 2 2014.4 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitssysteme GmbH...
- Page 155 AMAX panel 4000 / AMAX panel 4000 Technical Data | en France AFNOR NF a2P 1223400001A0 Environmental Class 1 Germany Home Bosch Sicherheitssysteme GmbH Installation Guide 2014.4 | 01 | F.01U.267.112...
- Page 158 Bosch Sicherheitssysteme GmbH Robert-Bosch-Ring 5 85630 Grasbrunn Germany www.boschsecurity.com © Bosch Sicherheitssysteme GmbH, 2014...