Casio KL-100 Quick Manual

KL-T100 Quick Guide
• The Chinese language dialects supported by this printer are
Standard Mandarin (Putonghua) and simplifi ed Chinese.
• QR code is a registered trademark of Denso Wave
Incorporated.
General Guide
Press to turn power on or off
Keyboard
Handwriting panel
Tape cartridge
compartment open button
USB connector
Plug in a USB cable to
connect the printer to
a computer.
AC adaptor
terminal
Connect the
specifi ed AC
adaptor.
Using the Touch Pen
You can use the printer's touch pen to write characters on the
handwriting panel and to perform various touch operations.
Removing the Touch Pen from Its Holder
When not in use, the touch pen is stowed in a holder near the
tape cartridge compartment cover.
Use the tip of your fi nder to slide the touch pen from its holder.
Precautions when Using the Touch Pen
• Excessive force is not required when using the touch pen to write
on the handwriting panel.
• Take care not to press too hard on the handwriting panel surface.
Doing so can crack or break the handwriting panel.
Power Requirements
MO1001-A
You can power your printer using the specifi ed AC adaptor or
commercially available alkaline batteries.
Using the AC Adaptor
Connecting the AC Adaptor to the Printer
• Use only the AC adaptor specifi ed for this printer.
1
Plug the AC adaptor plug into the printer's AC adaptor
terminal.
2
Plug the AC adaptor into a standard 100V AC household
power outlet.
LCD (main panel)
• For information about powering the printer using commercially
available alkaline batteries, see the KL-T100
Touch pen
Initialize printer memory fi rst!!
Tape outlet
Be sure to initialize printer memory before using the printer for
the fi rst time after purchasing it. Failure to initialize memory may
result in improper printer operation.
• Initializing printer memory will delete all data currently stored
Tape cartridge
in memory. Normally you should not initialize printer memory.
compartment
Perform this procedure only before using the printer for the fi rst
time after purchasing it.
1
Check to make sure that the printer is turned off.
Carrying handle
• The printer is on if there are characters on its display. If there
are, press
2
While holding down
press
Keep the keys depressed until the message
Unfold as shown
above to carry the
3
printer.
Press
4
Use and
settings.
Use and
Battery
confi gure.
compartment
• Use
cover
selected value and
it.
• You also can input values directly,
if you want.
5
After all the settings are the way you want, press
Turning Power On or Off
After you initialize printer operation, you will be able to use it
normally as soon as you turn it on by pressing
Changing the Display Language to Chinese
You can use the procedure below to change the language used
to display messages and menu item names to Chinese.
The initial factory default setting for the display language after
you purchase the printer is Japanese.
1
Press
2
Use and
3
Use and
• To switch back to Japanese, select
.
Calibrating the Handwriting Panel
You can use the procedure below to calibrate the handwriting
panel whenever the touch location is different from point you
touch, or when the characters you write are not displayed in the
correct locations.
1
Press
2
Use and
3
Use and
press
4
One-by-one, use the touch
pen to touch the centers of
the four cross marks (+) on
the handwriting panel.
• Each cross mark will become
dimmed after you touch it.
Handwriting panel adjustment is
complete after you touch all four
cross marks.
to turn it off.
and at the same time,
.
appears on the display.
.
to confi gure the current date and time
to select the setting you want to
to decrease the currently
to increase
.
and then .
to select and then press
中文
to select and then press
and then press
and then .
to select and then press
to select
.
Touch the center of Touch the center of
each cross. each cross.
Loading and Removing the Tape Cartridge
A tape cartridge must be loaded in the printer in order to print
labels. Use the tape cartridge that comes with the printer or a
commercially available tape cartridge.
To load a tape cartridge
1
Check to make sure that the printer is turned off.
• The printer is on if there are characters on its display. If there
are, press to turn it off.
2
Press the tape cartridge compartment open button and
open it.
3
Remove the stopper from the tape cartridge.
.
4
Check the condition of the tape and ink ribbon.
• Make sure the tip of the tape is not bent. If it is, use scissors
to cut off the bent part.
• Make sure the end of the tape is passing through the tape
guide.
• Make sure there is no slack in the ink ribbon.
Ink ribbon
(under tape)
• Never try to push tape back into the cartridge.
• Do not pull on the tape with excessive force. Doing so can
cause the ink ribbon to break, leading to malfunction.
• Loading a tape cartridge while its ink ribbon is slack can
cause the ink ribbon to break, leading to malfunction.
How to take up ink ribbon slack
If there is slack in the ink ribbon, use a
pencil or similar object to rotate the take-
up spool in the direction indicated by
arrow a in the nearby illustration. Keep
rotating until the lower left spool start to
rotate in the direction indicated by arrow
b . Note that the tape does not move
.
along with the ink ribbon at this time.
5
Load the tape cartridge into the printer.
• Taking care so the ink ribbon does not get pulled out, load
the cartridge so the tape and ink ribbon pass between the
print head and rubber roller (illustration below). Press down
on the tape cartridge as far as it will go, until it clicks into
place.
• Incorrectly loading the tape cartridge can cause the ribbon to
break.
.
.
.
and then
6
Close the tape cartridge compartment cover.
• Press down on the cover until is clicks securely into place.
• Do not pull on the tape or try to push it back in while the tape
cassette is loaded in the printer.
Stopper
Tape guide
Tape
(pull out approximately 3 cm)
Rubber roller
Tape
Print head