1. Manuals
  2. Brands
  3. Makita Manuals
  4. Impact Driver
  5. BTP140
  6. Instruction manual

Makita BTP140 Instruction Manual

Cordless 4 mode impact driver
Hide thumbs Also See for BTP140:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Instruction Manual
Cordless 4 Mode
Impact Driver
MODEL BTP130
MODEL BTP140
007155
I N S T R U C T I O N
M A N U A L
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Advertisement

Table of Contents
loading

Related Manuals for Makita BTP140

Summary of Contents for Makita BTP140

  • Page 1 Cordless 4 Mode Impact Driver MODEL BTP130 MODEL BTP140 007155 I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

  • Page 2: Specifications

    In observance of European Directive These values have been obtained according to EN60745. 2002/96/EC on waste electric and electronic equipment For Model BTP140 implementation in accordance with For European countries only national law, electric equipment that Noise and Vibration have reached the end of their life...

  • Page 3: General Safety Rules

    We declare under our sole responsibility that this product 8JD, ENGLAND is in compliance with the following standards of stan- Responsible manufacturer: dardized documents; Makita Corporation Anjo Aichi Japan EN60745, EN55014 in accordance with Council Direc- tives, 89/336/EEC, 98/37/EC. Yasuhiko Kanzaki CE2005 Director...

  • Page 4: Specific Safety Rules

    12. Remove any adjusting key or wrench before 24. Recharge only with the charger specified by the turning the power tool on. A wrench or a key left manufacturer. A charger that is suitable for one attached to a rotating part of the power tool may type of battery pack may create a risk of fire when result in personal injury.

  • Page 5: Important Safety Instructions

    Wear ear protectors with impact drills. Exposure Never recharge a fully charged battery car- to noise can cause hearing loss. tridge. Overcharging shortens the battery service life. SAVE THESE INSTRUCTIONS. Charge the battery cartridge with room temper- ature at 10°C - 40°C (50°F - 104°F). Let a hot bat- MISUSE or failure to follow the safety tery cartridge cool down before charging it.

  • Page 6: Functional Description

    FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Installing or removing battery cartridge 006667 • Always switch off the tool before insertion or removal of the battery cartridge.
  • Page 7 CAUTION: • Always check the direction of rotation before operation. • Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. • When not operating the tool, always set the reversing switch lever to the neutral position.
  • Page 8 Sliding to the mark is high rotation and the mark is low rotation. 007162 Before operation, always make sure that the lever is correctly set to your desired mode mark and use the tool at an appropriate speed for your work. CAUTION: •...
  • Page 9 For other countries 006349 To install these types of bits, follow A=17mm the procedure (1). B=14mm (Note) Makita bits are these types. To install these types of bits, follow A=12mm the procedure (2). B=9mm (Note) Bit-piece is necessary for installing the bit.

  • Page 10: Operation

    OPERATION CAUTION: • Always insert the battery cartridge all the way until it locks in place. If you can see the red part on the upper side of the button, it is not locked completely. Insert it fully until the red part cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.
  • Page 11 Tightening bolts The proper fastening torque may differ depending upon the kind or size of the 007318 screw/bolt, the material of the workpiece to be fastened, etc. The relation Standard bolt between fastening torque and fastening time is shown in the figures. (kgf cm) NOTE: (1224)
  • Page 12 CAUTION: • If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. Screwdriving operation CAUTION: • Adjust the adjusting ring to the proper torque level for your work. When driving small wood screws or machine screws.

  • Page 13: Maintenance

    Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a center-punch and hammer at the point to be drilled. Place the point of the bit in the indentation and start drilling. Use a cutting lubricant when drilling metals. The exceptions are iron and brass which should be drilled dry.
  • Page 14 CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
  • Page 15 Memo...
  • Page 16 Makita Corporation Anjo, Aichi, Japan 884655-223...

This manual is also suitable for:

Btp130

Table of Contents