Honeywell Lynx Plus Series Installation And Setup Manual page 30

Lynx Plus Series Installation and Setup Guide
Data Field Descriptions
✻
Field 57: Field *57 only applies
the selection is not valid the control will emit a single long beep indicating that the selection has been rejected. The
control replaces the selection with the default value, which is displayed on the keypad, and advances to the next field.
57 57 57 57
FALSE ALRM FALSE ALRM OPTS OPTS
FALSE FALSE ALRM ALRM OPTS OPTS
This field applies only to the
(
LynxSIA Plus control)
58 58 58 58
RF RF RF RF J J J J AM AM AM AM DETECT DETECTION DETECT DETECT ION ION ION
SYSTEM STATUS AND RESTORE REPORT CODES PROGRAMMING (✻59 – ✻76, & ✻89)
Report Codes can be programmed using the interactive ✻56 Enhanced Zone Programming Mode, or entered in data
fields ✻59-✻76 and ✻89. Use the following guidelines when programming report codes. The actual report code digits
entered depend upon the particular installation, and should be in agreement with you and the Central Station that will
receive the signals. Field ✻59 is used to program different features in the Lynx Plus and LynxSIA Plus controls. Field
✻69 applies only to LynxSIA Plus controls. Please be sure that you
installed.
With a 3+1 or 4+1 Standard Format: Enter a code in the first box: 1–9, A, B, C, D, E, or F. Enter "#+10" for A
(reports a "0" on some receivers), "#+11" for B, "#+12" for C, "#+13" for D, "#+14" for E, "#+15" for F. Entering "0" in the
first box will disable a report. Entering "0" in the second box results in automatic advance to the next field.
With an Expanded or 4+2 Format: Enter codes in both boxes (1st and 2nd digits) for 1–9, or A–F, as described above.
Entering "0" in the first box will disable a report. Entering "0" in the second box will eliminate the expanded message for
that report.
to the LynxSIA Plus control. The control validates the data entered in this field. If
False Alarm Options
(This field applies only to the LynxSIA Plus control)
Cancel Alarm Display
This option enables the display of aborted and cancelled alarms on the LynxSIA Plus
keypad. "CA" will be displayed.
Notes: (1) An abort occurs if the alarm panel is disarmed before it dials the alarm report to
the central station.
(2) A cancel occurs if the alarm panel is disarmed after the alarm is reported.
(3) Zone types 5, 6 and 7 (panic zone types) and 24 (silent burglary) cannot be
cancelled.
Auto Stay Arming
If this feature is enabled and the control panel has been armed "Armed Away" at the
Lynx Plus keypad or RF keypad, the system will switch to the "Armed Stay" mode if the
Exit Time has expired and no exit has been made.
Exit Time Restart-Exit Delay Restart/Reset
This option allows the control to restart the exit delay time
after arming in STAY mode by entering the User Code and pressing the STAY key (if
quick arming is disabled) or by pressing the STAY key (if quick arming is enabled).
This option also enables automatic exit delay reset, which resets exit delay if the
entry/exit door is re-opened and closed before exit delay time expires after arming.
Notes: (1) This avoids the need to disarm and then re-arm the system after allowing
someone to enter or exit.
(2) Automatic Exit Delay Reset occurs only once during an armed period.
LynxSIA Plus SELECTIONS
Cancel
Value Alarm Display
0 = Disabled
1 = Disabled
2 = Disabled
3 = Disabled
4 = Enabled
5 = Enabled
6 = Enabled
7 = Enabled
RF Jam Detection
For Event Logging, Option 2 must be selected. If the control detects an RF Jam
condition, a "FAULT" message appears for zone 90. The Contact ID® code for RF Jam is
344.
SELECTIONS
0 = no jam detection
1 = RF jam detection with event logging, but no central station report
2 = RF jam detection with event logging and with central station report (if trouble/restore
report is enabled in fields ✻60, ✻71)
Auto Stay Exit Time
Arming Restart/Reset
Disabled Disabled
Disabled Enabled
Enabled Disabled
Enabled Enabled
Disabled Disabled
Disabled Enabled
Enabled Disabled
Enabled Enabled
use the correct field for the control being
- 30 -