Honeywell Lynx Plus Series Installation And Setup Manual page 27

48 48 48 48
REP FRMT REP REP REP FRMT FRMT FRMT PRI PRI/S PRI PRI /SEC EC EC EC /S /S
49 49 49 49
SPLIT/DUAL SPLIT/DUAL REP SPLIT/DUAL SPLIT/DUAL REP REP REP
Report Format for Primary/Secondary
This field is used to select the Primary and Secondary Report Format. (For an
explanation of these formats, see the System Communication section of this manual).
Notes: (1) The maximum number of alarm and alarm restore reports during one armed
period is determined by field ✻92.
(2) If 3+1 dialer reporting is to be used, Enter
(3) If Option 5 is selected a 10-digit account number must be entered in Fields ✻43
or ✻44.
(4) Option 5 or 7 (ADEMCO Contact ID® Reporting) must be selected for AAV.
SELECTIONS
Primary
See choices below
0 = 3+1; 4+1 ADEMCO Low Speed Standard
1 = 3+1; 4+1 Radionics Standard
2 = 4+2 ADEMCO Low Speed Standard
3 = 4+2 Radionics Standard
5 = ADEMCO Contact ID® Reporting with 10-digit subscriber account number
6 = 4+2 ADEMCO Express
7 = ADEMCO Contact ID® Reporting with 4-digit subscriber account number
8 = 3+1; 4+1 ADEMCO Low Speed Expanded
9 = 3+1; 4+1 Radionics Expanded
Split/Dual Reporting
This field is used to select a reporting option as follows:
Enter: 0 - 5 when reporting to telephone receivers.
6 - 9 when reporting to a pager is desired
10 - 13 when reporting to an aux telephone receiver.
Note: If you are installing a communications module that has voice communications
capability (i.e.; GSMVL), refer to Field ✻ 55 notes for additional information.
Pager Report Format
Options 6-9 send reports to the primary phone number, in a format defined in Field
✻48, and send reports to a pager, which has its phone number entered as the secondary
phone number in Field ✻42. The pager report is a 7-digit code, with optional 16-digit
prefix. For an explanation of the pager format, refer to the User Guide.
Follow Me System Report Format
Options 10-13 send reports to the primary phone number, in a format defined in Field
✻48, and sends voice message to the secondary phone number entered in Field ✻42.
The message is a repeatable system status announcement. If the manual paging option
has been programmed in Field ✻87, the message will repeat "system, system.....". The
message can be terminated by pressing any key on the telephone keypad.
To Primary
0 = All reports
1 = Alarms, Restore, Cancel*
2 = All except Open/Close, Test
3 = Alarms, Restore, Cancel
4 = All except Open/Close, Test
5 = All reports
To Primary
6= All reports except Open/Close
7= All reports
8= All reports
9= All reports except Open/Close
To Primary
10= All reports except Open/Close
11 = All reports
12= All reports
13= All reports except Open/Close
*Recent close report is sent to primary number (LynxSIA Plus only)
‡ Will report Users 0, 5-8, and, if using wireless button-type devices, will report the zone number of the
arm or disarm button 26-33. All other zones and users are not reported.
Lynx Plus Series Installation and Setup Guide
Data Field Descriptions
Secondary
See choices below
To Secondary
None, unless primary fails, then all
Others
Open/Close, Test
All
All
All
To Paging Number
Alarms, Open/Close ‡, Troubles
Alarms, Troubles
Alarms, Open/Close ‡, Troubles
Open/Close ‡,
To Follow Me System Phone Number
Alarms, Open/Close ‡, Troubles
Alarms, Troubles
Alarms, Open/Close ‡, Troubles
Open/Close ‡
- 27 -
as the 4th digit of 43 through
✻ ✻
44.
✻