Honeywell Lynx Plus Series Installation And Setup Manual page 21

25 25 25 25
X10 HOUSE X10 X10 X10 HOUSE CODE HOUSE HOUSE CODE CODE CODE
26 26 26 26
CHIME BY BY BY BY ZONE CHIME ZONE
CHIME CHIME ZONE ZONE
27 27 27 27
CLOCK DISPLAY CLOCK DISPLAY
CLOCK CLOCK DISPLAY DISPLAY
29 29 29 29
DST MNTH DST MNTH STR STR/END END
DST DST MNTH MNTH STR STR END END
30 30 30 30
DST WEEK DST WEEK STR STR/END END
DST DST WEEK WEEK STR STR END END
31 31 31 31
SINGLE ALARM SINGLE ALARM SND SND
SINGLE SINGLE ALARM ALARM SND SND
32 32 32 32
FIRE SND FIRE FIRE FIRE SND SND T T T T IMEOUT SND IMEOUT IMEOUT IMEOUT
Powerline Carrier Device (X10) House ID
Powerline Carrier Devices require a House ID. This field identifies this House ID to the
Control. The Powerline Carrier Devices are programmed in field ✻80.
SELECTIONS
0 = A 3 = D 6 = G
1 = B 4 = E 7 = H
2 = C 5 = F 8 = I
Chime by Zone
This option allows the installer to define the specific zones intended to chime when
faulted while the system is in Chime mode. If enabled, these zones are defined in zone
list 3 (see ✻81 Zone List Menu Mode).
SELECTIONS
0 = no (chimes on fault of any entry/exit or perimeter zone when Chime mode is activated)
1 = yes (chimes on fault of those zones assigned to Zone List 3 when Chime mode on)
Real Time Clock Display
Refer to the User's Manual for setting the clock time and date.
SELECTIONS
0 = do not display the time
1 = display the time
Daylight Savings Time Start/End Month
Enter # + 10 for 10, # + 11 for 11, and # + 12 for 12.
SELECTIONS
0 = do not display the time
1 = display the time
Daylight Savings Time Start/End Month
Enter the appropriate start and end weekend of the month.
SELECTIONS
0 = disable
1 = first weekend of month
2 = second weekend
3 = third weekend
Single Alarm sounding Per Zone
This field applies only to burglary zones (zone response types 1-5, 10). It applies only to
the bell and does not affect keypad sounds.
UL installations: must be 0 (no limit)
Lynx Plus SELECTIONS
0 = no limit on alarm sounding per zone
1 = limit alarm sounding to once per arming period for a given zone
LynxSIA Plus SELECTIONS
0 = alarm sounding per zone will be the same as Swinger Shutdown set in field ✻92
1 = limit alarm sounding to once per arming period for a given zone
Sounder Timeout
This Control complies with NFPA requirements for temporal pulse sounding of fire and
carbon monoxide (CO) notification appliances. Temporal pulse sounding for a fire alarm
consists of the following:
3 pulses – pause – 3 pulses – pause – 3 pulses. . .
Temporal pulse sounding for a CO alarm consists of the following:
4 pulses – pause – 4 pulses – pause – 4 pulses –pause. . .
SELECTIONS
0 = yes, sounder timeout after time programmed in field ✻33
1 = no sounder timeout; continue sounding until manually turned off
Lynx Plus Series Installation and Setup Guide
Data Field Descriptions
9 = J
# + 10 = K
# + 11 = L
4 = fourth weekend
5 = last weekend
6 = next to last
7 = 3rd from last
(per armed period)
- 21 -
# + 12 = M # + 15 = P
# + 13 = N
# + 14 = O