Page 1 Vigor2710 Series User’s Guide...
Page 2 Vigor2710 Series User’s Guide...
Page 3 Vigor2710 Series ADSL2/2+ Firewall Router User’s Guide Version: 3.0 Firmware Version: V3.6.3 Date: 12/12/2012 Vigor2710 Series User’s Guide...
Page 4: Copyright Information
Owner Due to the continuous evolution of DrayTek technology, all routers will be regularly Firmware & Tools upgraded. Please consult the DrayTek web site for more information on newest Updates firmware, tools and documents. http://www.draytek.com Vigor2710 Series User’s Guide...
Page 5: European Community Declarations
Product: Vigor2710 Series Router DrayTek Corp. declares that Vigor2710 Series of routers are in compliance with the following essential requirements and other relevant provisions of R&TTE Directive 1999/5/EEC. The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive 2004/108/EC by complying with the requirements set forth in EN55022/Class B and EN55024/Class B.
Page 6 Vigor2710 Series User’s Guide...
Page 7: Table Of Contents
3.4 Create a LAN-to-LAN Connection Between Remote Office and Headquarter ..... 51 3.5 Create a Remote Dial-in User Connection Between the Teleworker and Headquarter..58 3.6 LAN – Created by Using NAT ....................63 3.7 Calling Scenario for VoIP function ..................65 Vigor2710 Series User’s Guide...
Page 8 4.5.9 File Extension Object....................165 4.6 CSM ............................ 167 4.6.1 APP Enforcement Profile ....................168 4.6.2 URL Content Filter Profile..................... 170 4.6.3 Web Content Filter Profile..................... 174 4.7 Bandwidth Management ..................... 178 4.7.1 Sessions Limit....................... 178 viii Vigor2710 Series User’s Guide...
Page 9 4.14.1 System Status......................279 4.14.2 TR-069 ........................281 4.14.3 Administrator Password....................282 4.14.4 User Password ......................283 4.14.5 Login Page Greeting....................285 4.14.6 Configuration Backup ....................287 4.14.7 Syslog/Mail Alert ......................289 4.14.8 Time and Date ......................291 Vigor2710 Series User’s Guide...
Page 10 5.4 Checking If the ISP Settings are OK or Not ................ 313 5.5 Problems for 3G Network Connection ................314 5.6 Backing to Factory Default Setting If Necessary ..............314 5.7 Contacting Your Dealer ....................... 315 Vigor2710 Series User’s Guide...
Page 11: Introduction
Vigor2710 series is an ADSL router. It integrates IP layer QoS, NAT session/bandwidth management to help users control works well with large bandwidth. By adopting hardware-based VPN platform and hardware encryption of AES/DES/3DS, the router increases the performance of VPN greatly, and offers several protocols (such as IPSec/PPTP/L2TP) with up to 2 VPN tunnels.
Page 12: Led Indicators And Connectors
>>General Setup. (Such profile must be established under CSM menu) Interface Description Connecter for accessing the Internet through ADSL2/2+. LAN (1-4) Connecters for local networked devices. Connecter for USB storage device (Pen Driver/Mobile HD) or printer. Vigor2710 Series User’s Guide...
Page 13 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. Connecter for a power adapter. Power Switch. ON/OFF Vigor2710 Series User’s Guide...
Page 14: For Vigor2710N
Press the button once to enable (WLAN LED on) or WLAN disable (WLAN LED off) wireless connection. Connecter for accessing the Internet through ADSL2/2+. LAN (1-4) Connecters for local networked devices. Connecter for USB storage (Pen Driver Mobile/HD) or printer. Vigor2710 Series User’s Guide...
Page 15 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. Connecter for a power adapter. Power Switch. ON/OFF Vigor2710 Series User’s Guide...
Page 16: For Vigor2710Vn
Press the button once to enable (WLAN LED on) or WLAN disable (WLAN LED off) wireless connection. Connecter for accessing the Internet through ADSL2/2+. LAN (1-4) Connecters for local networked devices. Connecter for USB storage (Pen Driver Mobile/HD) or printer. Vigor2710 Series User’s Guide...
Page 17 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. Connecter for a power adapter. Power Switch. ON/OFF Vigor2710 Series User’s Guide...
Page 18: For Vigor2710Vdn
The WPS is off. Blinking Waiting for wireless client sending requests for connection about 2 minutes. Vigor2710 Series User’s Guide...
Page 19 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. Connector for a power adapter. Power Switch. ON/OFF Vigor2710 Series User’s Guide...
Page 20: Hardware Installation
Power on the device by pressing down the power switch on the rear panel. The system starts to initiate. After completing the system test, the ACT LED will light up and start blinking. Here, we take Annex A model as an example for describing hardware installation. Vigor2710 Series User’s Guide...
Page 21: Printer Installation
Before using it, please follow the steps below to configure settings for connected computers (or wireless clients). Connect the printer with the router through USB/parallel port. Open Start->Settings-> Printer and Faxes. Open File->Add a New Computer. A welcome dialog will appear. Please click Next. Vigor2710 Series User’s Guide...
Page 22 Click Local printer attached to this computer and click Next. In this dialog, choose Create a new port Type of port and use the drop down list to select Standard TCP/IP Port. Click Next. Vigor2710 Series User’s Guide...
Page 23 In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Printer Name or IP Address and type IP_192.168.1.1 as the port name. Then, click Next. Click Standard and choose Generic Network Card. Then, in the following dialog, click Finish. Vigor2710 Series User’s Guide...
Page 24 11. Select "LPR" on Protocol, type p1 (number 1) as Queue Name. Then click OK. Next please refer to the red rectangle for choosing the correct protocol and LPR name. Vigor2710 Series User’s Guide...
Page 25 Open Support >FAQ/Application Notes; find out the link of Printer Server and click it; then click the What types of printers are compatible with Vigor router? link. Note 2: Vigor router supports printing request from computers via LAN ports but not WAN port. Vigor2710 Series User’s Guide...
Page 26 This page is left blank. Vigor2710 Series User’s Guide...
Page 27: Initial Configuration
Please type “admin/admin” as the Username/Password and click Login. Note: If you fail to access to the web configuration, please go to “Trouble Shooting” for detecting and solving your problem. Vigor2710 Series User’s Guide...
Page 28 The web page can be logged out according to the chosen condition. The default setting is Auto Logout, which means the web configuration system will logout after 5 minutes without any operation. Change the setting for your necessity. Vigor2710 Series User’s Guide...
Page 29: Changing Password
Enter the login password (the default is admin) on the field of Old Password. Type the new password in New Password and Confirm Password fields. Then click OK to continue. Now, the password has been changed. Next time, use the new password to access the Web Configurator for this router. Vigor2710 Series User’s Guide...
Page 30: Quick Start Wizard
PPPoE, PPPoA, Bridged IP, or Routed IP. The router supports the ADSL WAN interface for Internet access. Available settings are explained as follows: Item Description Stands for Virtual Path Identifier. It is an 8-bit header inside each ATM cell that indicates where the cell Vigor2710 Series User’s Guide...
Page 31 Assign an IP address to the secondary DNS. Second DNS Now, you have to select an appropriate WAN connection type for connecting to the Internet through this router according to the settings that your ISP provided. Vigor2710 Series User’s Guide...
Page 32: Pppoe/Pppoa
If your ISP provides you the PPPoE connection, please select PPPoE for this router. The following page will be shown: Available settings are explained as follows: Item Description Assign a specific valid user name provided by the ISP. User Name Assign a valid password provided by the ISP. Password Vigor2710 Series User’s Guide...
Page 33: 1483 Bridged Ip
Click Next for viewing summary of such connection. Click Finish. Then, the system status of this protocol will be shown. Now, you can enjoy surfing on the Internet. If your ISP provides you the Bridge connection, click 1483 Bridged IP as the protocol. Vigor2710 Series User’s Guide...
Page 34 Type in all the information that your ISP provides for this protocol. Click Next for viewing summary of such connection. Click Finish. Then, the system status of this protocol will be shown. Now, you can enjoy surfing on the Internet. Vigor2710 Series User’s Guide...
Page 35: 1483 Routed Ip
Type in all the information that your ISP provides for this protocol. Click Next to see the following page. Click Finish. Then, the system status of this protocol will be shown. Now, you can enjoy surfing on the Internet. Vigor2710 Series User’s Guide...
Page 36: Service Activation Wizard
Free trial edition: it offers a period of trial for you to get acquainted with WCF function. Formal edition with license key: you can extend the license valid time manually. Note: If you activate Formal edition with license key first, the free trial edition will be invalid. Vigor2710 Series User’s Guide...
Page 37 Setting confirmation page will be displayed as follows, please click Next. Wait for a moment till the following page appears. When such page appears, you can enable or disable these services for your necessity. Then, click Finish. Vigor2710 Series User’s Guide...
Page 38 Later, if you need to extend the license valid time, you can also use the Service Activation Wizard again to reach your goal by clicking the radio button of Formal edition with license key and clicking Next. Vigor2710 Series User’s Guide...
Page 39: Voip Wizard
Use the same Account as phone 1 – If you don’t need to configure Phone 2 settings, simply check this box. Click it to get into the next setting page. Next Click it to give up the quick start wizard. Cancel Vigor2710 Series User’s Guide...
Page 40: Online Status
ADSL information, and so on. If you select PPPoE as the protocol, you will find out a link of Dial PPPoE or Drop PPPoE in the Online Status web page. Detailed explanation is shown below: Vigor2710 Series User’s Guide...
Page 41 Ready, HANDSHAKING, SHOWTIME and so on. Up Speed – Display the upstream rate. Down Speed – Display the downstream rate. SNR Margin – Display number of SRR Margin. Loop Att .- Display the number of Loop Attenuation. Vigor2710 Series User’s Guide...
Page 42: Virtual Wan
TX Rate - Display the speed of transmitted octets at the WAN interface. RX Packets - Display the total number of received packets at the WAN interface. RX Rate - Display the speed of received octets at the WAN interface. Vigor2710 Series User’s Guide...
Page 43: Saving Configuration
Please follow the steps below to finish the router registration. Please login the web configuration interface of Vigor router by typing “admin/admin” as User Name / Password. Click Support Area>>Production Registration from the home page. Vigor2710 Series User’s Guide...
Page 44 And click Login. If not, please refer to section 4.13 Creating an Account for MyVigor. The following page will be displayed after you logging in MyVigor. From this page, please click Add or Product Registration. Vigor2710 Series User’s Guide...
Page 45 When the following page appears, your router information has been added to the database. Now, you have finished the product registration. After clicking OK, you will see the following page. Your router has been registered to myvigor website successfully. Vigor2710 Series User’s Guide...
Page 46 This page is left blank. Vigor2710 Series User’s Guide...
Page 47: Application And Example
Note: For the IPv6 service, you have to configure WAN/LAN settings before using the service. For the IPv6 WAN settings for Vigor2710, there are five connection types to be chosen: PPP, TSPC, AICCU, DHCPv6 Client and Static IPv6. Access into the web configurator of Vigor2710. Open Internet Access>>IPv6. Vigor2710 Series User’s Guide...
Page 48 Different connection types will bring out different configuration page. Refer to the following: PPP – Dual Stack application, IPv4 and IPv6 services can be utilized at the same time Choose PPP and type the information for PPPoE of IPv4. Vigor2710 Series User’s Guide...
Page 49 Access into the setting page for IPv6 service, it is not necessary for you to configure anything. Click OK and open Online Status. If the connection is successful, you will get the IP address for IPv4 and IPv6 at the same time. Vigor2710 Series User’s Guide...
Page 50 (In the following figure, the TSPC information is obtained from http://gogo6.com/ after applied for the service.) Click OK and open Online Status. If the connection is successful, the physical connection will be shows as follows: Vigor2710 Series User’s Guide...
Page 51 (In the following figure, the AICCU information is obtained from https://www.sixxs.net/main/ after applied for the service.) Click OK and open Online Status. If the connection is successful, the physical connection will be shows as follows: Vigor2710 Series User’s Guide...
Page 52 DHCPv6 Client Choose DHCPv6 Client. Click one of the identity associations and type the IAID number. Click OK and open Online Status. If the connection is successful, the physical connection will be shows as follows: Vigor2710 Series User’s Guide...
Page 53 Static IPv6 Choose Static IPv6. Type IPv6 address, Prefix Length and Gateway Address. Click OK and open Online Status. If the connection is successful, the physical connection will be shows as follows: Vigor2710 Series User’s Guide...
Page 54 In the field of HCPv6 Server Configuration, when DHCPv6 service is enabled, you can assign available IPv6 address for the client manually. Note: When both mechanisms are enabled, the client can determine which mechanism to be used (e.g., the default mechanism for Windows7 is RADVD). Vigor2710 Series User’s Guide...
Page 55 IPv4 IP and IPv6 IP services. Its IPv6 address is seen with a format of 2001:200:dff:fff1:216:3eff:feb1:44d7. After getting the above message, it means the IPv6 service has been activated successfully. Vigor2710 Series User’s Guide...
Page 56 If not, only a steady turtle will be seen. If you can see a turtle dancing on the screen, that means IPv6 service is ready for you to access and utilize. Vigor2710 Series User’s Guide...
Page 57: How Can I Use Ftp To Get The Files From Usb Storage Device Connecting To Vigor Router
Setup a user account for the FTP service by using USB Application >>USB User Management. Click Enable to enable FTP/Samba User account. Here we add a new account "user1" and assign authorities “Read”, “Write” and “List” to it. Vigor2710 Series User’s Guide...
Page 58 Click OK to save the configuration. Make sure the FTP service is running properly. Please open a browser and type ftp://192.168.1.1. Use the account "user1" to login. When the following screen appears, it means the FTP service is running properly. Vigor2710 Series User’s Guide...
Page 59 Now, users in LAN of Vigor2710 can access into the USB storage device by typing ftp://192.168.1.1 on any browser. They can add or remove files / directories, depending on the Access Rule for FTP account settings in USB Application >>USB User Management. Vigor2710 Series User’s Guide...
Page 60: How To Customize Your Login Page
“Just for Carrie” is displayed as a heading on the login dialog box. After typing the username and password (defined in User Management>>User Profile), click Login. You can access into Internet or access into the Landing Page if configured in User Management>>General Setup. Vigor2710 Series User’s Guide...
Page 61: Create A Lan-To-Lan Connection Between Remote Office And Headquarter
For using PPP based services, such as PPTP, L2TP, you have to set general settings in PPP General Setup. For using IPSec-based service, such as IPSec or L2TP with IPSec Policy, you have to set general settings in IPSec General Setup, such as the pre-shared key that both parties have known. Vigor2710 Series User’s Guide...
Page 62 If an IPSec-based service is selected, you should further specify the remote peer IP Address, IKE Authentication Method and IPSec Security Method for this Dial-Out connection. If a PPP-based service is selected, you should further specify the remote peer IP Vigor2710 Series User’s Guide...
Page 63 Otherwise, it will apply the settings defined in IPSec General Setup above. If a PPP-based service is selected, you should further specify the remote peer IP Address, Username, Password, and VJ Compression for this Dial-In connection. Vigor2710 Series User’s Guide...
Page 64 PPP General Setup. For using IPSec-based service, such as IPSec or L2TP with IPSec Policy, you have to set general settings in IPSec General Setup, such as the pre-shared key that both parties have known. Vigor2710 Series User’s Guide...
Page 65 Set Dial-Out Settings as shown below to dial to connect to Router B aggressively with the selected Dial-Out method. If an IPSec-based service is selected, you should further specify the remote peer IP Address, IKE Authentication Method and IPSec Security Method for this Dial-Out connection. Vigor2710 Series User’s Guide...
Page 66 If an IPSec-based service is selected, you may further specify the remote peer IP Address, IKE Authentication Method and IPSec Security Method for this Dial-In connection. Otherwise, it will apply the settings defined in IPSec General Setup above. Vigor2710 Series User’s Guide...
Page 67 Address, Username, Password, and VJ Compression for this Dial-In connection. At last, set the remote network IP/subnet in TCP/IP Network Settings so that Router B can direct the packets destined to the remote network to Router A via the VPN connection. Vigor2710 Series User’s Guide...
Page 68: Create A Remote Dial-In User Connection Between The Teleworker And Headquarter
PPP General Setup. For using IPSec-based service, such as IPSec or L2TP with IPSec Policy, you have to set general settings in IKE/IPSec General Setup, such as the pre-shared key that both parties have known. Vigor2710 Series User’s Guide...
Page 69 Otherwise, it will apply the settings defined in IPSec General Setup above. If a PPP-based service is selected, you should further specify the remote peer IP Address, Username, Password, and VJ Compression for this Dial-In connection. Vigor2710 Series User’s Guide...
Page 70 After successful installation, for the first time user, you should click on the Step 0. Configure button. Reboot the host. In Step 2. Connect to VPN Server, click Insert button to add a new entry. If an IPSec-based service is selected as shown below, Vigor2710 Series User’s Guide...
Page 71 VPN router. To use default gateway on remote network means that all the packets of remote host will be directed to VPN server then forwarded to Internet. This will make the remote host seem to be working in the enterprise network. Vigor2710 Series User’s Guide...
Page 72 Click Connect button to build connection. When the connection is successful, you will find a green light on the right down corner. Vigor2710 Series User’s Guide...
Page 73: Lan - Created By Using Nat
You can just set the settings wrapped inside the red rectangles to fit the request of NAT usage. To use another DHCP server in the network rather than the built-in one of Vigor Router, you have to change the settings as show below. Vigor2710 Series User’s Guide...
Page 74 You can just set the settings wrapped inside the red rectangles to fit the request of NAT usage. Vigor2710 Series User’s Guide...
Page 75: Calling Scenario For Voip Function
SIP Accounts Settings --- Profile Name: iptel 1 Register via: Auto SIP Port: 5060(default) Domain/Realm: iptel.org Proxy: iptel.org Act as outbound proxy: unchecked Display Name: David Account Name: 4321 Authentication ID: unchecked Password: **** Expiry Time: (use default value) Vigor2710 Series User’s Guide...
Page 76 Expiry Time: (use default value) CODEC/RTP/DTMF --- John calls David (Use default value) He picks up the phone and dials 1111#. (DialPlan Phone Number for David) He picks up the phone and dials 4321#. (David’s Account Name) Vigor2710 Series User’s Guide...
Page 77: Peer-To-Peer Calling
Register via: None SIP Port: 5060(default) Domain/Realm: (blank) Proxy: (blank) Act as outbound proxy: unchecked Display Name: Arnor Account Name: 1234 Authentication ID: unchecked Password: (blank) Expiry Time: (use default value) CODEC/RTP/DTMF--- (Use default value) Arnor calls Paulin Vigor2710 Series User’s Guide...
Page 78 Display Name: Paulin Account Name: 4321 Authentication ID: unchecked Password: (blank) Expiry Time: (use default value) CODEC/RTP/DTMF--- (Use default value) Paulin calls Arnor He picks up the phone and dials 2222# (DialPlan Phone Number for John) Vigor2710 Series User’s Guide...
Page 79: Request A Certificate From A Ca Server On Windows Ca Server
Go to Certificate Management and choose Local Certificate. Vigor2710 Series User’s Guide...
Page 80 Copy and save the X509 Local Certificate Requet as a text file and save it for later use. Connect to CA server via web browser. Follow the instruction to submit the request. Below we take a Windows 2000 CA server for example. Select Request a Certificate. Vigor2710 Series User’s Guide...
Page 81 64 encoded certificate and Download CA certificate. Now you should get a certificate (.cer file) and save it. Back to Vigor router, go to Local Certificate. Click IMPORT button and browse the file to import the certificate (.cer file) into Vigor router. When finished, click refresh Vigor2710 Series User’s Guide...
Page 82 “------BEGINE CERTIFICATE------..” You may review the detail information of the certificate by clicking View button. Vigor2710 Series User’s Guide...
Page 83: Request A Ca Certificate And Set As Trusted On Windows Ca Server
Use web browser connecting to the CA server that you would like to retrieve its CA certificate. Click Retrive the CA certificate or certificate recoring list. Vigor2710 Series User’s Guide...
Page 84 You may review the detail information of the certificate by clicking View button. Note: Before setting certificate configuration, please go to System Maintenance >> Time and Date to reset current time of the router first. Vigor2710 Series User’s Guide...
Page 85: Creating An Account For Myvigor
1. Click CSM>> Web Content Filter Profile. The following page will appear. Click System Maintenance>>Activation to open the following page. 2. Click the Activate link. A login page for MyVigor web site will pop up automatically. Vigor2710 Series User’s Guide...
Page 86 3. Click the link of Create an account now. 4. Check to confirm that you accept the Agreement and click Accept. Vigor2710 Series User’s Guide...
Page 87 5. Type your personal information in this page and then click Continue. 6. Choose proper selection for your computer and click Continue. Vigor2710 Series User’s Guide...
Page 88 New Account Confirmation Letter from myvigor.draytek.com. 9. Click the Activate my Account link to enable the account that you created. The following screen will be shown to verify the register process is finished. Please click Login. Vigor2710 Series User’s Guide...
Page 89: Creating An Account Via Myvigor Web Site
11. Now, click Login. Your account has been activated. You can access into MyVigor server to activate the service (e.g., WCF) that you want. 1. Access into http://myvigor.draytek.com. Find the line of Not registered yet?. Then, click the link Click here! to access into next page. Vigor2710 Series User’s Guide...
Page 90 2. Check to confirm that you accept the Agreement and click Accept. 3. Type your personal information in this page and then click Continue. 4. Choose proper selection for your computer and click Continue. Vigor2710 Series User’s Guide...
Page 91 New Account Confirmation Letter from myvigor.draytek.com. 7. Click the Activate my Account link to enable the account that you created. The following screen will be shown to verify the register process is finished. Please click Login. Vigor2710 Series User’s Guide...
Page 92 Auth Code according to the value displayed on the right side of it. Now, click Login. Your account has been activated. You can access into MyVigor server to activate the service (e.g., WCF) that you want. Vigor2710 Series User’s Guide...
Page 93: Advanced Configuration
NIC has reserved certain addresses that will never be registered publicly. These are known as private IP addresses, and are listed in the following ranges: From 10.0.0.0 to 10.255.255.255 From 172.16.0.0 to 172.31.255.255 From 192.168.0.0 to 192.168.255.255 Vigor2710 Series User’s Guide...
Page 94: Pppoe/Pppoa
ADSL loop and your ISP’s Digital Subscriber Line Access Multiplexer (SDLAM). To choose PPPoE or PPPoA as the accessing protocol of the internet, please select PPPoE/PPPoA from the Internet Access menu. The following web page will be shown. Vigor2710 Series User’s Guide...
Page 95 Select M-PVCs Channel means no selection will be chosen. VPI - Type in the value provided by ISP. VCI - Type in the value provided by ISP. Encapsulating Type - Drop down the list to choose the type provided by ISP. Vigor2710 Series User’s Guide...
Page 96 It means Max Transmit Unit for packet. The default setting is 1442. If you check this box to invoke the function, the router will Bridge Mode work as a bridge. WAN Backup Setup Dial Backup Mode - If you install a 3G USB modem on the Vigor2710 Series User’s Guide...
Page 97 WAN Connection Detection - Such function allows you to verify whether network connection is alive or not through ARP Detect or Ping Detect. Mode – Choose ARP Detect or Ping Detect for the system Vigor2710 Series User’s Guide...
Page 98 Idle Timeout – Set the timeout for breaking down the Internet after passing through the time without any action. This setting is active only when the Active on demand option for Active Mode is selected in WAN>> General Setup page. Vigor2710 Series User’s Guide...
Page 99 All the schedules can be set previously in Applications – Schedule web page and you can use the number that you have set in that web page. After finishing all the settings here, please click OK to activate them. Vigor2710 Series User’s Guide...
Page 100: Mpoa
DSL Modem Settings vital for building DSL connection to your ISP. Multi-PVC channel - The selections displayed here are determined by the page of Internet Access – Multi PVCs. Select M-PVCs Channel means no selection will be chosen. Vigor2710 Series User’s Guide...
Page 101 Dial Backup Mode - If you install a 3G USB modem on the router, choose the 3G USB Modem to perform WAN backup via USB device. Then, click the 3G USB Modem Backup link to access into the following page for configuring detailed settings. Vigor2710 Series User’s Guide...
Page 102 WAN detection. Ping IP – If you choose Ping Detect as detection mode, you have to type IP address in this field for pinging. TTL (Time to Live) – Displays value for your reference. Vigor2710 Series User’s Guide...
Page 103 Type in the primary IP address for the router. If necessary, DNS Server IP Address type in secondary IP address for necessity in the future. After finishing all the settings here, please click OK to activate them. Vigor2710 Series User’s Guide...
Page 104: Ipv6
After getting the IPv6 prefix and starting router advertisement daemon (RADVD), the PC behind this router can directly connect to IPv6 the Internet. Available settings are explained as follows: Vigor2710 Series User’s Guide...
Page 105 Type the address for the tunnel broker IP, FQDN or an Tunnel Broker optional port number. Type the subnet prefix address getting from service provider Subnet Prefix After finishing all the settings here, please click OK to activate them. Vigor2710 Series User’s Guide...
Page 106 After finishing all the settings here, please click OK to activate them. – – This type allows you to setup static IPv6 address for WAN interface. Available settings are explained as follows: Item Description IPv6 Address – Type the IPv6 Static IP Address. Static IPv6 Address Vigor2710 Series User’s Guide...
Page 107 Add – Click it to add a new entry. Delete – Click it to remove an existed entry. Display current interface IPv6 address. Current IPv6 Address Table After finishing all the settings here, please click OK to activate them. Vigor2710 Series User’s Guide...
Page 108: Multi-Pvcs
Internet Access. Type in the value provided by your ISP. Type in the value provided by your ISP. Select a proper QoS type for the channel. QoS Type Select a proper protocol for this channel. Protocol Vigor2710 Series User’s Guide...
Page 109 WAN link for Channel 3, 4, 5 are provided for router-borne application such as TR-069 and VoIP. The settings must be applied and obtained from your ISP. For your special request, please contact with your ISP and then click WAN link of Channel 3, 4 or 5 to configure your router. Vigor2710 Series User’s Guide...
Page 110 Username – Type in the username provided by ISP in this field. Password – Type in the password provided by ISP in this field. PPP Authentication – Select PAP only or PAP or CHAP for PPP. Vigor2710 Series User’s Guide...
Page 111 Type in the primary IP address for the router. If necessary, DNS Server IP Address type in secondary IP address for necessity in the future. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 112 It represents Sustainable Cell Rate. The value of SCR must be smaller than PCR. It represents Maximum Burst Size. The range of the value is 10 to 50. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 113 Click Clear to remove all the configurations in this page if you do not satisfy it. When you finish the configuration, please click OK to save and exit this page. Or click Cancel to abort the configuration and exit this page. Vigor2710 Series User’s Guide...
Page 114 And type the number for VLAN ID (number). To add the packet priority number for such VLAN. The Priority range is from 0 to 7. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 115: Lan
IP address. As a part of the public subnet, the Vigor router will serve for IP routing to help hosts in the public subnet to communicate with other public hosts or servers outside. Therefore, the router should be set as the gateway for public hosts. Vigor2710 Series User’s Guide...
Page 116 You can group local hosts by physical ports and create up to 4 virtual LANs. To manage the communication between different groups, please set up rules in Virtual LAN (VLAN) function and the rate of each. Vigor2710 Series User’s Guide...
Page 117: General Setup
2nd Subnet Mask - An address code that determines the size of the network. (Default: 255.255.255.0/ 24) 2nd Subnet DHCP Server - You can configure the router to serve as a DHCP server for the 2nd subnet. Vigor2710 Series User’s Guide...
Page 118 The router by factory default acts a DHCP server for your Configuration network so it automatically dispatch related IP settings to any local user configured as a DHCP client. It is highly recommended that you leave the router enabled as a DHCP Vigor2710 Series User’s Guide...
Page 119 DNS Server IP address: 194.98.0.1 to this field. The default DNS Server IP address can be found via Online Status: If both the Primary IP and Secondary IP Address fields are Vigor2710 Series User’s Guide...
Page 120 There are two configuration pages for LAN1, Ethernet TCP/IP and DHCP Setup (based on IPv4) and IPv6 Setup. Click the tab for each type and refer to the following explanations for detailed information. Below shows the settings page for IPv6. Vigor2710 Series User’s Guide...
Page 121 Add – Click it to add a new entry. Delete – Click it to remove an existed entry. Display current used IPv6 addresses. Current IPv6 Address Table After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 122: Static Route
The number (1 to 10) under Index allows you to open next Index page to set up static route. Displays the destination address of the static route. Destination Address Displays the status of the static route. Status Vigor2710 Series User’s Guide...
Page 123 Destination Address Displays the status of the static route. Status Click any underline of index number to get the following page. Available settings are explained as follows: Item Description Click it to enable this profile. Enable Vigor2710 Series User’s Guide...
Page 124 Subnet. The first is that the LAN interface can exchange RIP packets with the neighboring routers via the 1st subnet (192.168.1.0/24). The second is that those hosts on the internal private subnets (ex. 192.168.10.0/24) can access the Internet Vigor2710 Series User’s Guide...
Page 125 Return to Static Route Setup page. Click on another Index Number to add another static route as show below, which regulates all packets destined to 211.100.88.0 will be forwarded to 192.168.1.3. Go to Diagnostics and choose Routing Table to verify current routing table. Vigor2710 Series User’s Guide...
Page 126: Vlan
P3 and P4. After checking the box to enable VLAN function, you will check the table according to the needs as shown below. To remove VLAN, uncheck the needed box and click OK to save the results. Vigor2710 Series User’s Guide...
Page 127: Bind Ip To Mac
Each pair of IP and MAC address listed in ARP table can be selected and added to IP Bind List by clicking Add below Click this link to select all the items in the ARP table. Select All Reorder the table based on the IP address. Sort Vigor2710 Series User’s Guide...
Page 128: Nat
192.168.1.0/24 subnet for the router. As stated before, the NAT facility can map one or more IP addresses and/or service ports into different specified services. In other words, the NAT function can be achieved by using port mapping methods. Vigor2710 Series User’s Guide...
Page 129: Port Redirection
The port redirection can only apply to incoming traffic. To use this function, please go to NAT page and choose Port Redirection web page. The Port Redirection Table provides 20 port-mapping entries for the internal hosts. Vigor2710 Series User’s Guide...
Page 130 Display the IP address of the internal host providing the Private IP service. Display if the profile is enabled (v) or not (x). Status Press any number under Index to access into next page for configuring port redirection. Available settings are explained as follows: Vigor2710 Series User’s Guide...
Page 131 80 to avoid conflict, such as 8080. This can be set in the System Maintenance >>Management Setup. You then will access the admin screen of by suffixing the IP address with 8080, e.g., http://192.168.1.1:8080 instead of port 80. Vigor2710 Series User’s Guide...
Page 132 Vigor2710 Series User’s Guide...
Page 133: Dmz Host
We suggest you to add additional filter rules or a secondary firewall. Click DMZ Host to open the following page: Available settings are explained as follows: Item Description Choose None, Private IP or Active True IP first. Active True IP selection is available for WAN1 only. Vigor2710 Series User’s Guide...
Page 134 Aux. WAN IP for your selection. Available settings are explained as follows: Item Description Check to enable the DMZ Host function. Enable Enter the private IP address of the DMZ host, or click Choose Private IP PC to select one. Vigor2710 Series User’s Guide...
Page 135 IP address in the list to be the DMZ host. When you have selected one private IP from the above dialog, the IP address will be shown on the following screen. Click OK to save the setting. Vigor2710 Series User’s Guide...
Page 136: Open Ports
Inactive or Active state. To add or edit port settings, click one index number on the page. The index entry setup page will pop up. In each index entry, you can specify 10 port ranges for diverse services. Vigor2710 Series User’s Guide...
Page 137 Specify the starting port number of the service offered by the Start Port local host. Specify the ending port number of the service offered by the End Port local host. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 138: Address Mapping
Host3 always map to 203.98.200.10 (WAN2) and Group 1 to always map to 202.211.100.10 (WAN1). Available settings are explained as follows: Item Description Indicate the relative number for the particular entry that you Index want to configure You should click the appropriate index Vigor2710 Series User’s Guide...
Page 139 WAN side and have source address as configured in the WAN IP field. Select a value of subnet mask for private IP address. Subnet Mask After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 140: Firewall
It will check packets according to the filter rules. If legal, the packet will pass the router. The following illustrations are flow charts explaining how router will treat incoming traffic and outgoing traffic respectively. Vigor2710 Series User’s Guide...
Page 141 4. Port Scan attack 12. Tear drop attack 5. IP options 13. Ping of Death attack 6. Land attack 14. ICMP fragment 7. Smurf attack 15. Unknown protocol 8. Trace route Below shows the menu items for Firewall. Vigor2710 Series User’s Guide...
Page 142: General Setup
For the sake of security, the router will execute strict security checking for data transmission. Such feature is enabled in default. All the packets, while transmitting through Vigor router, will be filtered by firewall. If the firewall system (e.g., content filter server) does not Vigor2710 Series User’s Guide...
Page 143 The default setting is 60000. Choose one of the QoS rules to be applied as firewall rule. For Quality of Service detailed information of setting QoS, please refer to the related section later. Vigor2710 Series User’s Guide...
Page 144 Advance Setting strongly recommended to use the default settings here. Codepage - This function is used to compare the characters among different languages. Choose correct codepage can help the system obtaining correct ASCII after decoding data from Vigor2710 Series User’s Guide...
Page 145 (0~65535). The more the value is, the better the performance will be. However, if the network is not stable, small value will be proper. Session timeout – Setting timeout for sessions can make the best utilization of network resources. Vigor2710 Series User’s Guide...
Page 146: Filter Setup
Use Up or Down link to move the order of the filter rules. Move Up/Down Set the link to the next filter set to be executed after the Next Filter Set current filter run. Do not make a loop with many filter sets. Vigor2710 Series User’s Guide...
Page 147 Set the direction of packet flow. It is for Data Filter only. For Direction the Call Filter, this setting is not available since Call Filter is only applied to outgoing traffic. Note: RT means routing domain for 2nd subnet. Vigor2710 Series User’s Guide...
Page 148 Click Edit to access into the following dialog to choose a Service Type suitable service type. To set the service type manually, please choose User defined as the Service Type and type them in this dialog. In addition, Vigor2710 Series User’s Guide...
Page 149 The number typed here is the total sessions of the packets Sessions Control that do not match the filter rule configured in this page. The default setting is 12000. Vigor2710 Series User’s Guide...
Page 150 CSM>> Web Content Filter web page first. Or choose [Create New] from the drop down list in this page to create a new profile. For troubleshooting needs, you can specify to record information for Web Content Filter by checking the Vigor2710 Series User’s Guide...
Page 151 Window size – It determines the size of TCP protocol (0~65535). The more the value is, the better the performance will be. However, if the network is not stable, small value will be proper. Vigor2710 Series User’s Guide...
Page 152 Checking is enabled. If Strict Security Checking is not enabled, then the packets will pass through the router. APP Enforcement – Check this box to execute the critical checking for all the files transferred via IM/P2P. Vigor2710 Series User’s Guide...
Page 153 Each filter set is composed by 7 filter rules, which can be further defined. After that, in General Setup you may specify one set for call filter and one set for data filter to execute first. Vigor2710 Series User’s Guide...
Page 154: Dos Defense
Check the box to activate the UDP flood defense function. Enable UDP flood Once detecting the Threshold of the UDP packets from the defense Internet has exceeded the defined value, the Vigor router will start to randomly discard the subsequent UDP packets for a Vigor2710 Series User’s Guide...
Page 155 Check the box to activate the Block fraggle Attack function. Block Fraggle Attack Any broadcast UDP packets received from the Internet is blocked. Activating the DoS/DDoS defense functionality might block some legal packets. For example, when you activate the Vigor2710 Series User’s Guide...
Page 156 All the warning messages related to DoS Defense will be sent to user and user can review it through Syslog daemon. Look for the keyword DoS in the message, followed by a name to indicate what kind of attacks is detected. Vigor2710 Series User’s Guide...
Page 157 Item Description Vigor2710 Series User’s Guide...
Page 158: Objects Settings
IPs in the same department can be defined with an IP object (a range of IP address). You can set up to 192 sets of IP Objects with different conditions. Each item is explained as follows: Item Description Display a name for this profile. Name Clear all profiles. Set to Factory Default Vigor2710 Series User’s Guide...
Page 159 If you choose LAN as the Interface here, and choose LAN as the direction setting in Edit Filter Rule, then all the IP addresses specified with LAN interface will be opened for you to choose in Edit Filter Rule page. Vigor2710 Series User’s Guide...
Page 160 If it is checked, all the IP addresses except the ones listed Invert Selection above will be applied later while it is chosen. After finishing all the settings here, please click OK to save the configuration. Below is an example of IP objects settings. Vigor2710 Series User’s Guide...
Page 161: Ip Group
Display the profile number that you can configure. Index Display the name of the group profile. Name To set a new profile, please do the steps listed below: Click the number (e.g., #1) under Index column for configuration in details. Vigor2710 Series User’s Guide...
Page 162 Click >> button to add the selected IP objects in this box. Selected IP Objects After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 163: Ipv6 Object
Display the profile number that you can configure. Index Display the name of the object profile. Name To set a new profile, please do the steps listed below: 1. Click the number (e.g., #1) under Index column for configuration in details. Vigor2710 Series User’s Guide...
Page 164 End IP Address selected. Type the fixed value for prefix length. Prefix Len If it is checked, all the IPv6 addresses except the ones listed Invert Selection above will be applied later while it is chosen. Vigor2710 Series User’s Guide...
Page 165: Ipv6 Group
This page allows you to bind several IPv6 objects into one IPv6 group. Each item is explained as follows: Item Description Clear all profiles. Set to Factory Default Display the profile number that you can configure. Index Display the name of the group profile. Name Vigor2710 Series User’s Guide...
Page 166 Objects Click >> button to add the selected IPv6 objects in this box. Selected IPv6 Objects 3. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 167: Service Type Object
Display the profile number that you can configure. Index Display the name of the object profile. Name To set a new profile, please do the steps listed below: 1. Click the number (e.g., #1) under Index column for configuration in details. Vigor2710 Series User’s Guide...
Page 168 (<) – the port number less than this value is available for this profile. After finishing all the settings here, please click OK to save the configuration. Below is an example of service type objects settings. Vigor2710 Series User’s Guide...
Page 169: Service Type Group
Display the profile number that you can configure. Index Display the name of the group profile. Name To set a new profile, please do the steps listed below: Click the number (e.g., #1) under Group column for configuration in details. Vigor2710 Series User’s Guide...
Page 170 Objects Setting>>Service Type Object will be shown in Type Objects this box. Click >> button to add the selected IP objects in this box. Selected Service Type Objects 3. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 171: Keyword Object
Display the profile number that you can configure. Index Display the name of the object profile. Name To set a new profile, please do the steps listed below: 1. Click the number (e.g., #1) under Index column for configuration in details. Vigor2710 Series User’s Guide...
Page 172 Contents. When you browse the webpage, the page with gambling information will be watched out and be passed/blocked based on the configuration on Firewall settings. 3. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 173: Keyword Group
Display the profile number that you can configure. Index Display the name of the group profile. Name To set a new profile, please do the steps listed below: 1. Click the number (e.g., #1) under Index column for configuration in details. Vigor2710 Series User’s Guide...
Page 174 Selected Keyword Click button to add the selected Keyword objects in Objects this box. 3. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 175: File Extension Object
Display the profile number that you can configure. Index Display the name of the object profile. Name To set a new profile, please do the steps listed below: 1. Click the number (e.g., #1) under Profile column for configuration in details. Vigor2710 Series User’s Guide...
Page 176 3. Type a name for such profile and check all the items of file extension that will be processed in the router. 4. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 177: Csm
Please note that this action will not introduce any delay in your Web surfing because each of multiple load balanced database servers can handle millions of requests for categorization. Vigor2710 Series User’s Guide...
Page 178: App Enforcement Profile
Click the number under Index column for settings in detail. There are three tabs IM, P2P and Misc displayed on this page. Each tab will bring out different items that you can choose to disallow people using. Vigor2710 Series User’s Guide...
Page 179 Clear All The profiles configured here can be applied in the Firewall>>General Setup and Firewall>>Filter Setup pages as the standard for the host(s) to follow. The items categorized under P2P ----- The items categorized under Misc ----- Vigor2710 Series User’s Guide...
Page 180: Url Content Filter Profile
Each item is explained as follows: Item Description Clear all profiles. Set to Factory Default Display the number of the profile which allows you to click Profile to set different policy. Display the name of the URL Content Filter Profile. Name Vigor2710 Series User’s Guide...
Page 181 URL first, then Web feature second. Either: Web Feature First –When all the packages matching with the conditions specified in URL Access Control and Web Feature below, such function can determine Vigor2710 Series User’s Guide...
Page 182 The keyword could be a noun, a partial noun, or a complete URL string. Multiple keywords within a frame are separated by space, comma, or semicolon. Vigor2710 Series User’s Guide...
Page 183 Upload – Check the box to reject any file upload job. File Extension Profile – Choose one of the profiles that you configured in Object Setting>> File Extension Objects previously for passing or blocking the file downloading. Vigor2710 Series User’s Guide...
Page 184: Web Content Filter Profile
Click CSM and click Web Content Filter Profile to open the profile setting page. The default setting for Setup Query Server /Setup Test Server is auto-selected. You can choose another server for your necessity by clicking Find more to open http://myvigor.draytek.com for searching another qualified and suitable one. Vigor2710 Series User’s Guide...
Page 185 Click this link to retrieve the factory settings. Set to Factory Default You can type the message manually for your necessity or Default Message click this button to get the default message which will be displayed on the field of Administration Message. Vigor2710 Series User’s Guide...
Page 186 If you have and activate another web content filter license, the items will be changed simultaneously. All of the configuration made for web content filter will be deleted automatically. Therefore, please backup your data before you change the web content filter license. Vigor2710 Series User’s Guide...
Page 187 Block – Only the log about Block will be recorded in Syslog. All – All the actions (Pass and Block) will be recorded in Syslog. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 188: Bandwidth Management
Hosts. In the Bandwidth Management menu, click Sessions Limit to open the web page. To activate the function of limit session, simply click Enable and set the default session limit. Available settings are explained as follows: Vigor2710 Series User’s Guide...
Page 189 All the schedules can be set previously in Application >> Schedule web page and you can use the number that you have set in that web page. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 190: Bandwidth Limit
Disable - Click this button to close the function of limit bandwidth. Default TX limit - Define the default speed of the upstream for each computer in LAN. Default RX limit - Define the default speed of the Vigor2710 Series User’s Guide...
Page 191 All the schedules can be set previously in Application >> Schedule web page and you can use the number that you have set in that web page. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 192: Quality Of Service
The core routers in the backbone will do the same checking before executing treatments in order to ensure service-level consistency throughout the whole QoS-enabled network. Vigor2710 Series User’s Guide...
Page 193 Class 1/Class2/Class 3/Others – Display the bandwidth percentage for each class. UDP Bandwidth Control –Display the UDP bandwidth control is enabled or not. Online Statistics –Display an online statistics for quality of service for your reference Vigor2710 Series User’s Guide...
Page 194 There are four queues allowed for QoS control. The first three (Class 1 to Class 3) class rules can be adjusted for your necessity. Yet, the last one is reserved for the packets which are not suitable for the user-defined class rules. Vigor2710 Series User’s Guide...
Page 195 Check this and set the limited bandwidth ratio on the right Enable UDP Bandwidth field. This is a protection of TCP application traffic since UDP Control application traffic such as streaming video will exhaust lots of bandwidth. Vigor2710 Series User’s Guide...
Page 196 Available settings are explained as follows: Item Description Display the name of such class. Name Check the box to tag the packets with the header selected in the Tag packets as drop down list for this class. Vigor2710 Series User’s Guide...
Page 197 Click the Edit button to set the local IP address (on LAN) for Local Address the rule. Click the Edit button to set the remote IP address (on Remote Address LAN/WAN) for the rule. Vigor2710 Series User’s Guide...
Page 198 Edit to open the rule edit page for modification. To add a new service type, edit or delete an existed service type, please click the Edit link under Service Type field. Vigor2710 Series User’s Guide...
Page 199 For adding a new service type, click Add to open the following page. Available settings are explained as follows: Item Description Type in a new service for your request. Service Name Choose the type (TCP, UDP or TCP/UDP or other) for the Service Type new service. Vigor2710 Series User’s Guide...
Page 200 For example, in the following illustration, the VoIP packets in LAN go into Vigor router without any header. However, when they go forward to the Server on ISP through Vigor router, all of the packets are tagged with AF (configured in Bandwidth >>QoS>>Class) automatically. Vigor2710 Series User’s Guide...
Page 201: App Qos
Click Disable to deactivate APP QoS function. Each tab offers different types of protocols to fit your Protocol/Misc request. Click it to select all of the protocols. Select All Click it to de-select all of the protocols. Clear All Vigor2710 Series User’s Guide...
Page 202: Applications
DDNS service providers. Basically, Vigor routers are compatible with the DDNS services supplied by most popular DDNS service providers such as www.dyndns.org, www.no-ip.com, www.dtdns.com, www.changeip.com, www.dynamic- nameserver.com. You should visit their websites to register your own domain name for the router. Vigor2710 Series User’s Guide...
Page 203 Account, and choose correct Service Provider: dyndns.org, type the registered hostname: hostname and domain name suffix: dyndns.org in the Domain Name block. The following two blocks should be typed your account Login Name: test and Password: test. Vigor2710 Series User’s Guide...
Page 204 DDNS update will take place right away. Internet IP – If it is selected and the WAN IP of Vigor router is private, it will be converted to public IP before DDNS update takes place. Vigor2710 Series User’s Guide...
Page 205: Schedule
You can set up to 15 schedules. Then you can apply them to your Internet Access or VPN and Remote Access >> LAN-to-LAN settings. To add a schedule: 1. Click any index, say Index No. 1. Vigor2710 Series User’s Guide...
Page 206 How often -Specify how often the schedule will be applied Once -The schedule will be applied just once Weekdays -Specify which days in one week should perform the schedule. Click OK button to save the settings. Vigor2710 Series User’s Guide...
Page 207: Radius
Check to enable RADIUS client feature. Enable Enter the IP address of RADIUS server Server IP Address The UDP port number that the RADIUS server is using. The Destination Port default value is 1812, based on RFC 2138. Vigor2710 Series User’s Guide...
Page 208: Upnp
The NAT Traversal of UPnP enables the multimedia features of your applications to operate. This has to manually set up port mappings or use other similar methods. The screenshots below show examples of this facility. Vigor2710 Series User’s Guide...
Page 209 Some Microsoft operating systems have found out the UPnP weaknesses and hence you need to ensure that you have applied the latest service packs and patches. Non-privileged users can control some router functions, including removing and adding port mappings. Vigor2710 Series User’s Guide...
Page 210: Igmp
After finishing all the settings here, please click OK to save the configuration. If you check Enable IGMP Proxy, all the multicast groups will be listed and all the LAN ports (P1 to P4) are available for use. Vigor2710 Series User’s Guide...
Page 211: Wake On Lan
Type any one of the MAC address of the bound PCs. MAC Address Click this button to wake up the selected IP. See the Wake Up following figure. The result will be shown on the box. Vigor2710 Series User’s Guide...
Page 212: Vpn And Remote Access
Enable the necessary VPN service as you need. If you intend to run a VPN server inside your LAN, you should disable the VPN service of Vigor Router to allow VPN tunnel pass through, as well as the appropriate NAT settings, such as DMZ or open port. Vigor2710 Series User’s Guide...
Page 213: Ppp General Setup
PAP or CHAP - Selecting this option means the router will attempt to authenticate dial-in users with the CHAP protocol first. If the dial-in user does not support this protocol, it will fall back to use the PAP protocol for authentication. Vigor2710 Series User’s Guide...
Page 214: Ipsec General Setup
Encapsulating Security Payload (ESP) for the following IKE exchange and mutual examination of the secure tunnel establishment. There are two encapsulation methods used in IPSec, Transport and Tunnel. The Transport mode will add the AH/ESP payload and use original IP header to encapsulate the data Vigor2710 Series User’s Guide...
Page 215 High - Encapsulating Security Payload (ESP) means payload (data) will be encrypted and authenticated. You may select encryption algorithm from Data Encryption Standard (DES), Triple DES (3DES), and AES. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 216: Ipsec Peer Identity
Click each index to edit one peer digital certificate. There are three security levels of digital signature authentication: Fill each necessary field to authenticate the remote peer. The following explanation will guide you to fill all the necessary fields. Vigor2710 Series User’s Guide...
Page 217 The field includes Country (C), State (ST), Location (L), Organization (O), Organization Unit (OU), Common Name (CN), and Email (E). After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 218: Remote Dial-In User
Click each index to edit one remote user profile. Each Dial-In Type requires you to fill the different corresponding fields on the right. If the fields gray out, it means you may leave it untouched. The following explanation will guide you to fill all the necessary fields. Vigor2710 Series User’s Guide...
Page 219 Must -Specify the IPSec policy to be definitely applied on the L2TP connection. Specify Remote Node Check the checkbox-You can specify the IP address of the remote dial-in user, ISDN number or peer ID (used in IKE aggressive mode). Vigor2710 Series User’s Guide...
Page 220 By default, this option is invoked. You can uncheck it to disable it. High-Encapsulating Security Payload (ESP) means payload (data) will be encrypted and authenticated. You may select encryption algorithm from Data Encryption Standard (DES), Triple DES (3DES), and AES. Vigor2710 Series User’s Guide...
Page 221: Lan To Lan
Trunk – Click it to display the Trunk profiles. Click to clear all indexes. Set to Factory Default Indicate the name of the LAN-to-LAN profile. The Name symbol ??? represents that the profile is empty. Check the box to enable the selected profile. Active Vigor2710 Series User’s Guide...
Page 222 LAN-to-LAN connection. Enable this profile - Check here to activate this profile. VPN Dial-Out Through - Use the drop down menu to choose a proper WAN interface for this profile. This setting is useful for dial-out only. Vigor2710 Series User’s Guide...
Page 223 VPN connection for router’s judgment of redial. Normally, if any one of VPN peers wants to disconnect the connection, it should follow a serial of packet exchange procedure to inform each other. However, if the remote peer Vigor2710 Series User’s Guide...
Page 224 Profiles set in the VPN and Remote Access >>IPSec Peer Identity as Peer ID. Local ID – Specify which one will be inspected first. Alternative Subject Name First – The alternative Vigor2710 Series User’s Guide...
Page 225 However, the Aggressive mode is faster. The default value in Vigor router is Main mode. IKE phase 1 proposal-To propose the local available authentication schemes and encryption algorithms to the VPN peers, and get its feedback to find a match. Two Vigor2710 Series User’s Guide...
Page 226 Local ID-In Aggressive mode, Local ID is on behalf of the IP address while identity authenticating with remote VPN server. The length of the ID is limited to 47 characters. Available settings are explained as follows: Vigor2710 Series User’s Guide...
Page 227 Digital Signature to invoke this function and select one predefined Profiles set in the VPN and Remote Access >>IPSec Peer Identity. Local ID – Specify which one will be inspected first. Alternative Subject Name First – The alternative Vigor2710 Series User’s Guide...
Page 228 PPTP or L2TP. Remote Network IP/ Remote Network Mask - Add a static route to direct all traffic destined to this Remote Network IP Address/Remote Network Mask through the VPN connection. Vigor2710 Series User’s Guide...
Page 229 VPN tunnel. Note that this setting is available only for one WAN interface is enabled. It is not available when both WAN interfaces are enabled. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 230: Connection Management
Item Description Click this button to execute dial out function. Dial Choose the time for refresh the dial information among 5, 10, Refresh Seconds and 30. Click this button to refresh the whole connection status. Refresh Vigor2710 Series User’s Guide...
Page 231: Certificate Management
Remember to adjust the time of Vigor router before using the certificate so that you can get the correct valid period of certificate. Below shows the menu items for Certificate Management. Available settings are explained as follows: Item Description Click this button to open Generate Certificate Request Generate window. Vigor2710 Series User’s Guide...
Page 232 Click this button to view the detailed settings for certificate View request. Click this button to delete selected name with certification Delete information. After clicking Generate, the generated information will be displayed on the window below: Vigor2710 Series User’s Guide...
Page 233: Trusted Ca Certificate
For viewing each trusted CA certificate, click View to open the certificate detail information window. If you want to delete a CA certificate, choose the one and click Delete to remove all the certificate information. Vigor2710 Series User’s Guide...
Page 234: Certificate Backup
The more bandwidth a codec uses the better the voice quality, however the codec used must be appropriate for your Internet bandwidth. Usually there will be two types of calling scenario, as illustrated below: Vigor2710 Series User’s Guide...
Page 235 QoS Assurance assists to assign high priority to voice traffic via Internet. You will always have the required inbound and outbound bandwidth that is prioritized exclusively for Voice traffic over Internet but you just get your data a little slower and it is tolerable for data traffic. Vigor2710 Series User’s Guide...
Page 236: Dialplan
SIP addresses. Loop through and Backup Phone Number will be displayed if you are using Vigor 2710Vn/VDn for setting the phone book. Vigor2710 Series User’s Guide...
Page 237 Available settings are explained as follows: Item Description Click this to enable this entry. Enable The speed-dial number of this index. This can be any number Phone Number you choose, using digits 0-9 and * . Vigor2710 Series User’s Guide...
Page 238 PSTN phone, the telecom co. might charge you for the connection fee. Please type in backup phone number (PSTN number/ISDN number) for this VoIP phone setting. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 239 Replace - When you choose this mode, the OP number will be replaced by the prefix number for calling out through the specific VoIP interface. Take the above picture (Prefix Table Setup web page) as an example, the prefix number of Vigor2710 Series User’s Guide...
Page 240 VoIP>> Phone Settings. Click the link to move the selected entry up or down. Move UP /Move Down Call barring is used to block phone calls coming from the one that is not welcomed. Vigor2710 Series User’s Guide...
Page 241 All means all the phone calls will be blocked with such Route mechanism. Enter the index of schedule profiles to control the call Index (1-15) in barring according to the preconfigured schedules. Refer to Schedule section Applications>>Schedule for detailed configuration. Vigor2710 Series User’s Guide...
Page 242 For Block Anonymous – this function can block the incoming calls without caller ID on the interface (Phone port) specified in the following window. Such control also can be done based on preconfigured schedules. Web page for Vigor2710Vn--- Web page for Vigor2710VDn--- Vigor2710 Series User’s Guide...
Page 243 SIP accounts. Web page for Vigor2710Vn--- Web page for Vigor2710VDn--- For Block IP Address – this function can block incoming calls (through Phone port) coming from IP address. Web page for Vigor2710Vn--- Web page for Vigor2710DVn--- Vigor2710 Series User’s Guide...
Page 244 Call Forward [No incoming calls to the specified place while there is no answer Ans][Act] of the connected phone. Dial the number typed in this field to invoke the function of Do Not Disturb [Act] DND. Vigor2710 Series User’s Guide...
Page 245 PSTN relay. Then, check the Enable box to make the PSTN number available for dial whenever you need. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 246: Sip Accounts
As Vigor VoIP Router is turned on, it will first register with Registrar using AuthorizationUser@Domain/Realm. After that, your call will be bypassed by SIP Proxy to the destination using AccountName@Domain/Realm as identity. SIP Accounts Web Page for Vigor2710 Vn ------- Vigor2710 Series User’s Guide...
Page 247 Type in the IP address or domain of the STUN server. STUN Server Type in the gateway IP address. External IP The default value is 150 (sec). It is useful for a Nortel server SIP PING interval Vigor2710 Series User’s Guide...
Page 248 Item Description NAT Traversal Support. Click any index link to open the following web page. SIP Accounts Web Page for Vigor2710 Vn ------- Vigor2710 Series User’s Guide...
Page 249 Set the domain name or IP address of the SIP Registrar server. Domain/Realm Set domain name or IP address of SIP proxy server. By the Proxy time you can type :port number after the domain name to Vigor2710 Series User’s Guide...
Page 250 SIP URL by the time out. SIP URL – Type in the SIP URL (e.g., aaa@draytel.org or abc@iptel.org) as the site for call forwarded. Vigor2710 Series User’s Guide...
Page 251 If not, the router will do something to save the bandwidth for other using. Click On to invoke this function; click off to close the function. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 252: Phone Settings
Port – Phone, Phone1/Phone2 allow you to set general Phone List settings for PSTN phones. DECT1-6 allow you to set general settings for DECT phone. Call Feature – A brief description for call feature will be Vigor2710 Series User’s Guide...
Page 253 The default value is 15000. RTP TOS – It decides the level of VoIP package. Use the drop down list to choose any one of them. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 254 DECT Port Web Page for Vigor2710 VDn ------- Available settings are explained as follows: Item Description Check the box to enable it. Type in the SIP URL in the field Hotline for dialing automatically when you pick up the phone set. Vigor2710 Series User’s Guide...
Page 255 ID type automatically. Or you can adjust tone settings manually if you choose User Defined. TOn1, TOff1, TOn2 and TOff2 mean the cadence of the tone pattern. TOn1 and TOn2 represent sound-on; TOff1 and TOff2 represent the sound-off. Vigor2710 Series User’s Guide...
Page 256 Congestion tone will be shown automatically on the page. If you cannot find out a suitable one, please choose User Defined and fill out the corresponding values for dial tone, ringing tone, busy tone, congestion tone by yourself for VoIP phone. Vigor2710 Series User’s Guide...
Page 257 Payload Type (rfc2833) - Choose a number from 96 to 127, the default value was 101. This setting is available for the OutBand (RFC2833) mode. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 258: Dect
If your handset has registered to the router, you could use this Deregister Handset button to deregister it from router. Check this box to enable the function to avoid hearing noisy Wideband Voice voice. Check this box to enable the function. Ring Handset Vigor2710 Series User’s Guide...
Page 259 6 phone registrations. Open VoIP>>DECT. Note: DECT menu will appear if DECT module is detected. In the web page, please click Enable Registration Mode and wait for DECT handset to register. Vigor2710 Series User’s Guide...
Page 260 When the registration is finished, open VoIP>>SIP Accounts. The Registered DECT phone will be available for you to choose. Choose the one you need. Open VoIP>>Status. Information for the active DECT phone will be shown as follows. Vigor2710 Series User’s Guide...
Page 261 When registering with DECT phone, you will be asked to type access code. The default setting in Vigor2710VDn is 1234. Please open VoIP>>Phone Settings to modify it if required. The following diagram shows the brief construction of DECT phone (handset) and Vigor router. Vigor2710 Series User’s Guide...
Page 262: Status
From this page, you can find codec, connection and other important call status for each port. For Vigor2710 Vn ------- For Vigor2710 VDn ------- Vigor2710 Series User’s Guide...
Page 263 Accumulation for the times of in call. In Calls Accumulation for the times of out call. Out Calls Accumulation for the times of missing call. Miss Calls The volume of present call. Speaker Gain Display logs of VoIP calls. Vigor2710 Series User’s Guide...
Page 264: Wireless Lan
SSID as identification, located channel etc. Real-time Hardware Encryption: Vigor Router is equipped with a hardware AES encryption engine so it can apply the highest protection to your data without influencing user experience. Vigor2710 Series User’s Guide...
Page 265 MAC addresses to isolate users’ access from wired LAN. Manage Wireless Stations - Station List will display all the station in your wireless network and the status of their connection. Below shows the menu items for Wireless LAN. Vigor2710 Series User’s Guide...
Page 266: General Setup
Check the box to enable wireless function. Enable Wireless LAN At present, the router can connect to Mixed (11b+11g), 11g Mode Only, 11b Only, Mixed (11g+11n), 11n Only and Mixed (11b+11g+11n) stations simultaneously. Simply choose Mix (11b+11g+11n) mode. Vigor2710 Series User’s Guide...
Page 267 If you have no idea of choosing the frequency, please select Auto to let system determine for you. This option is to define the length of the sync field in an Long Preamble Vigor2710 Series User’s Guide...
Page 268 Upload – Check Enable and type the transmitting rate for data upload. Default value is 30,000 kbps. Download – Type the transmitting rate for data download. Default value is 30,000 kbps. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 269: Security
By clicking the Security Settings, a new web page will appear so that you could configure the settings of WEP and WPA. Available settings are explained as follows: Item Description There are several modes provided for you to choose. Mode Vigor2710 Series User’s Guide...
Page 270 The keys can be entered in ASCII or Hexadecimal. Check the key you wish to use. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 271: Access Control
SSIDs desired to insert this MAC address into their access control list. s: Isolate the station from LAN - select to isolate the wireless Attribute connection of the wireless client of the MAC address from LAN. Add a new MAC address into the list. Vigor2710 Series User’s Guide...
Page 272: Wps
On the side of Vigor 2710 series which served as an AP, press WPS button once on the front panel of the router or click Start PBC on web configuration interface. On the side of a station with network card installed, press Start PBC button of network card. Vigor2710 Series User’s Guide...
Page 273 Please click OK and go back Wireless LAN>>Security to choose WPA-PSK or WPA2-PSK mode and access WPS again. Below shows Wireless LAN>>WPS web page. Available settings are explained as follows: Item Description Check this box to enable WPS setting. Enable WPS Vigor2710 Series User’s Guide...
Page 274 Start PIN button. The WPS LED PinCode on the router will blink fast when WPS is in progress. It will return to normal condition after two minutes. (You need to setup WPS within two minutes) Vigor2710 Series User’s Guide...
Page 275: Wds
To meet the above requirement, two WDS modes are implemented in Vigor router. One is Bridge, the other is Repeater. Below shows the function of WDS-bridge interface: The application for the WDS-Repeater mode is depicted as below: Vigor2710 Series User’s Guide...
Page 276 Bridge 2 through WDS links. However, hosts connected to Bridge 1 CANNOT communicate with hosts connected to Bridge 3 through Bridge 2. Click WDS from Wireless LAN menu. The following page will be shown. Vigor2710 Series User’s Guide...
Page 277 Type – There are some types for you to choose. WPA and Pre-shared Key WPA2 are used for WDS devices (e.g.2920n wireless router, you can set the encryption mode as WPA or WPA2 to establish Vigor2710 Series User’s Guide...
Page 278: Advanced Setting
Green Field – to get the highest throughput, please choose such mode. Such mode can make the data transmission happening between 11n systems only. In addition, it does not have protection mechanism to avoid the conflict with neighboring devices of 802.11a/b/g. Vigor2710 Series User’s Guide...
Page 279: Wmm Configuration
Wi-Fi networks. It allows devices to take more time in sleeping state and consume less power to improve the performance by minimizing transmission latency. Such function is designed for mobile and cordless phones that support VoIP mostly. Vigor2710 Series User’s Guide...
Page 280 “Check” the box means the AP router will not answer any response request for the transmitting packets. It will have better performance with lower reliability. After finishing all the settings here, please click OK to save the configuration. Vigor2710 Series User’s Guide...
Page 281: Ap Discovery
AP’s MAC address on the bottom of the page and click Bridge or Repeater. Next, click Add to. Later, the MAC address of the AP will be added to Bridge or Repeater field of WDS settings page. Vigor2710 Series User’s Guide...
Page 282: Station List
WLAN station and click Add to Access Control below. Available settings are explained as follows: Item Description Click this button to refresh the status of station list. Refresh Click this button to add current typed MAC address into Access Control. Vigor2710 Series User’s Guide...
Page 283: Usb Application
Simultaneous FTP Connections - This field is used to General Settings specify the quantity of the FTP sessions. The router allows up to 6 FTP sessions connecting to USB storage disk at one time. Default Charset - Vigor router supports four types of Vigor2710 Series User’s Guide...
Page 284: Usb User Management
USB disk first. Otherwise, an error message will appear to warn you. Each item is explained as follows: Item Description Display the number link of the profile. Index Vigor2710 Series User’s Guide...
Page 285 Type the username for FTP users for accessing into FTP Username server (USB disk). Be aware that users cannot access into USB disk in anonymity. Later, you can open FTP client software and type the username specified here for accessing Vigor2710 Series User’s Guide...
Page 286 Directory –Check the items (List, Create and Remove) for such profile. Before you click OK, you have to insert a USB disk into the USB interface of the Vigor router. Otherwise, you cannot save the configuration. Vigor2710 Series User’s Guide...
Page 287: File Explorer
Create Display current folder. Current Path Click this button to upload the selected file to the USB Upload storage disk. The uploaded file in the USB storage disk can be shared for other user through FTP. Vigor2710 Series User’s Guide...
Page 288: Usb Disk Status
FTP server. It displays the username that user uses to login to the FTP Username server. When you insert USB disk into the Vigor router, the system will start to find out such device within several seconds. Vigor2710 Series User’s Guide...
Page 289: System Maintenance
WAN interface information. Also, you could get the current running firmware version or firmware related information from this presentation. Each item is explained as follows: Item Description Display the model name of the router. Model Name Vigor2710 Series User’s Guide...
Page 290 Scope - Display the scope of IPv6 address. For example, IPv6 Link Local could only be used for direct IPv6 link. It can't be used for IPv6 internet. Internet Access Mode – Display the connection mode chosen for accessing into Internet. Vigor2710 Series User’s Guide...
Page 291: 281
CPE. The default setting is Enable. Please set interval time or Periodic Inform Settings schedule time for the router to send notification to CPE. Or click Disable to close the mechanism of notification. Vigor2710 Series User’s Guide...
Page 292: Administrator Password
Type in new password in this field. New Password Type in the new password again. Confirm Password When you click OK, the login window will appear. Please use the new password to access into the web configurator again. Vigor2710 Series User’s Guide...
Page 293: User Password
Below shows an example for accessing into User Operation with User Password. 1. Open System Maintenance>>User Password. 2. Check the box of Enable User Mode for simple web configuration to enable user mode operation. Type a new password in the field of New Password and click OK. Vigor2710 Series User’s Guide...
Page 294 4. Log out Vigor router Web Configurator by clicking Logout. 5. The following window will be open to ask for username and password. It is no need to type any username. Type the new user password in the filed of Password and click Login. Vigor2710 Series User’s Guide...
Page 295: Login
At that moment, the background of the web page is blank and no heading will be displayed on the Login window. This page allows you to specify background message and the heading on the Login window if you have such requirement. Vigor2710 Series User’s Guide...
Page 296 Preview the settings on this web page. Click to return to the factory default setting. Set to Factory Default Below shows an example of login customization with the information typed in Login Page Title and Bulletin. Vigor2710 Series User’s Guide...
Page 297: Configuration Backup
Click Backup button to get into the following dialog. Click Save button to open another dialog for saving configuration as a file. In Save As dialog, the default filename is config.cfg. You could give it another name by yourself. Vigor2710 Series User’s Guide...
Page 298 Click Browse button to choose the correct configuration file for uploading to the router. Click Restore button and wait for few seconds, the following picture will tell you that the restoration procedure is successful. Vigor2710 Series User’s Guide...
Page 299: Syslog/Mail Alert
Mail Alert Setup Send a test e-mail - Make a simple test for the e-mail address specified in this page. Please assign the mail address first and click this button to execute a test for verify the mail Vigor2710 Series User’s Guide...
Page 300 From the Syslog screen, select the router you want to monitor. Be reminded that in Network Information, select the network adapter used to connect to the router. Otherwise, you won’t succeed in retrieving information from the router. Vigor2710 Series User’s Guide...
Page 301: Time And Date
Check the box to enable the daylight saving. Such feature is Enable Daylight Saving available for certain area. Select a time interval for updating from the NTP server. Automatically Update Interval Click OK to save these settings. Vigor2710 Series User’s Guide...
Page 302: Management
List IP - Indicate an IP address allowed to login to the router. Subnet Mask - Represent a subnet mask allowed to login to the router. User Defined Ports - Check to specify user-defined port Management Port Setup Vigor2710 Series User’s Guide...
Page 303 Enable PING from the Internet - Check the checkbox to enable all PING packets from the Internet. For security issue, this function is disabled by default. You could specify that the system administrator can only Access List Vigor2710 Series User’s Guide...
Page 304: Reboot System
Note: When the system pops up Reboot System web page after you configure web settings, please click Reboot Now to reboot your router for ensuring normal operation and preventing unexpected errors of the router in the future. Vigor2710 Series User’s Guide...
Page 305: Firmware Upgrade
(or local DrayTek's web site) and FTP site is ftp.draytek.com. Click System Maintenance>> Firmware Upgrade to launch the Firmware Upgrade Utility. Click OK. The following screen will appear. Please execute the firmware upgrade utility first. Vigor2710 Series User’s Guide...
Page 306: Activation
Display the mechanism (represented with code number, e.g., Status CT-CF) adopted by such router. As for authentication information of web filter, the process Authentication Message of authenticating will be displayed on this field for your reference. Vigor2710 Series User’s Guide...
Page 307 Below shows the successful activation of Web Content Filter: Display the starting date of WCF license activated Start Date successfully. Display the ending date of WCF license activated Expire Date successfully. Vigor2710 Series User’s Guide...
Page 308: Diagnostics
Each item is explained as follows: Item Description It shows the source IP address (local), destination IP Decoded Format (remote) address, the protocol and length of the package. Click it to reload the page. Refresh Vigor2710 Series User’s Guide...
Page 309: Routing Table
Click Diagnostics and click Routing Table to open the web page. Available settings are explained as follows: Item Description Click it to reload the page. Refresh Vigor2710 Series User’s Guide...
Page 310: Arp Cache Table
IPv6 address. This information is helpful in diagnosing network problems, such as IP address conflicts, etc. Click Diagnostics and click IPv6 Neighbour Table to open the web page. Available settings are explained as follows: Item Description Click it to reload the page. Refresh Vigor2710 Series User’s Guide...
Page 311: Dhcp Table
It displays the MAC address for the specified PC that DHCP MAC Address assigned IP address for it. It displays the leased time of the specified PC. Leased Time It displays the host ID name of the specified PC. HOST ID Vigor2710 Series User’s Guide...
Page 312: Nat Sessions Table
It indicates the temporary port of the router used for NAT. #Pseudo Port It indicates the destination IP address and port of remote host. Peer IP:Port It displays the representing number for different interface. Interface Click it to reload the page. Refresh Vigor2710 Series User’s Guide...
Page 313: Data Flow Monitor
Click this link to refresh this page manually. Refresh Display the number of the data flow. Index Display the IP address of the monitored device. IP Address Display the transmission speed of the monitored device. TX rate (kbps) Vigor2710 Series User’s Guide...
Page 314 Peak means the highest peak value detected by the router in data transmission. Speed means line speed specified in WAN>>General Setup. If you do not specify any rate at that page, here will display Auto for instead. Vigor2710 Series User’s Guide...
Page 315: Traffic Graph
Bandwidth chart, the numbers displayed on vertical axis represent the numbers of the transmitted and received packets in the past. For Sessions chart, the numbers displayed on vertical axis represent the numbers of the NAT sessions during the past. Vigor2710 Series User’s Guide...
Page 316: Ping Diagnosis
Type the IPv6 address that you want to ping. Ping IPv6 Address Click this button to start the ping work. The result will be displayed on the screen. Click this link to remove the result on the window. Clear Vigor2710 Series User’s Guide...
Page 317: Trace Route
It indicates the IPv6 address of the host if IPv6 protocol is Trace Host/IP Address selected. Click this button to start route tracing work. Click this link to remove the result on the window. Clear Vigor2710 Series User’s Guide...
Page 318: Product Registration
When you click it, you will be guided to visit myvigor.draytek.com and open the corresponding pages directly. Click Support Area>>Product Registration, the following web page will be displayed. Vigor2710 Series User’s Guide...
Page 319: Trouble Shooting
Turn on the router. Make sure the ACT LED blink once per second and the correspondent LAN LED is bright. If not, it means that there is something wrong with the hardware status. Simply back to “1.3 Hardware Installation” to execute the hardware installation again. And then, try again. Vigor2710 Series User’s Guide...
Page 320 Go to Control Panel and then double-click on Network Connections. Right-click on Local Area Connection and click on Properties. Select Internet Protocol (TCP/IP) and then click Properties. Vigor2710 Series User’s Guide...
Page 321 Select Obtain an IP address automatically and Obtain DNS server address automatically. Double click on the current used Mac OS on the desktop. Open the Application folder and get into Network. On the Network screen, select Using DHCP from the drop down list of Configure IPv4. Vigor2710 Series User’s Guide...
Page 322: Pinging The Router From Your Computer
Open the Application folder and get into Utilities. Double click Terminal. The Terminal window will appear. Type ping 192.168.1.1 and press [Enter]. If the link is OK, the line of “64 bytes from 192.168.1.1: icmp_seq=0 ttl=255 time=xxxx ms” will appear. Vigor2710 Series User’s Guide...
Page 323: Checking If The Isp Settings Are Ok Or Not
Click Internet Access group and then check whether the ISP settings are set correctly. Check if the Enable option is selected. Check if Username and Password are entered with correct values that you got from your ISP. Vigor2710 Series User’s Guide...
Page 324: Problems For 3G Network Connection
Warning: After pressing factory default setting, you will loose all settings you did before. Make sure you have recorded all useful settings before you pressing. The password of factory default is null. Vigor2710 Series User’s Guide...
Page 325: Contacting Your Dealer
After restore the factory default setting, you can configure the settings for the router again to fit your personal request. If the router still cannot work correctly after trying many efforts, please contact your dealer for further help right away. For any questions, please feel free to send e-mail to support@draytek.com. Vigor2710 Series User’s Guide...

This manual is also suitable for:

Vigor2710n Vigor2710vn Vigor2710vdn

Draytek Vigor2710 Series User Manual

Quick Links

Related Manuals for Draytek Vigor2710 Series

Summary of Contents for Draytek Vigor2710 Series

This manual is also suitable for:

Table of Contents