Sony STR-DA7100ES Service Manual page 26

STR-DA7100ES
Items
DSP RAM
Bass management
DSP Version display
Volume value display (FL/FR)
Volume value display (SL/SR)
Volume value display (CT/SW)
Volume value display
(SBL/SBR)
EERROM debug
Super reset
2nd volume value display
3rd volume value display
FL display duty change
SDRAM check
i.LINK 232C update
i.LINK1394C update
Model A AC write
i.LINK test mode
YUV Y drive
YUV U drive
YUV V drive
26
Display
DSP RAM
[*****]=XXXXXXXX
SPECIAL
BASS MAN [****] XX
SPECIAL
DSP Ver S: ***, P: XXX
SPECIAL
FL**** FR XXXX
SPECIAL
SL**** SR XXXX
SPECIAL
CT**** SW XXXX
SPECIAL
SBL**** SBR XXXX
SPECIAL
EEPROM [****] FR XX
SPECIAL
SUPER RESET [XXX]
SPECIAL
2nd VOLUME XXX
SPECIAL
3nd VOLUME XXX
SPECIAL
DARK OUT DUTY [XXX%]
SPECIAL
SDRAM CHECK [XXXXX]
SPECIAL
i.LINK 232C Update?
SPECIAL
i.LINK 1394C Update?
SPECIAL
MODEL/AAC WRITE [XXX]
SPECIAL
i.LINK TEST MODE IN?
SPECIAL
YUV Y DRIVE [XX]
SPECIAL
YUV U DRIVE [XX]
SPECIAL
YUV V DRIVE [XX]
The umbers which can be changed wick blinks
To select the digit: Press the [TUNING +] or [TUNING -] button
To select the number when the umbers (***** or XXXX) blinks:
Rotate the –/+ dial
To perform the write when the umbers (XXXX) blinks:
Press the [MEMORY/ENTER] button
***** : instruction RAM address
XXXXXXXX: instruction RAM address
Note: When parenthesis is the position of instruction RAM
address data, up/down of the menu item by the [MENU] dial
are invalid
****: AUTO or OFF, XX: 02 to 29
(switching with –/+ dial)
***: DSP decoder patch version
XXX: DSP post process version
****: Front L-ch volume value
XXXX: Front R-ch volume value
****: Surround L-ch volume value
XXXX: Surround R-ch volume value
****: Center volume value
XXXX: Sub woofer R-ch volume value
****: Surround back L-ch volume value
XXXX: Surround back R-ch volume value
****: EEPROM address
XX: EEPROM data (switching with –/+ dial)
Not used for the servicing
If super reset is performed, "up convert signal level adjustment"
will also be initialized
When EEPROM initialization is required, perform the "all clear
mode"
XXX: 2nd room volume value (00 to )
XX: 3rd room volume value (00 to )
XXX: Duty value of FL display (0% to 100%)
(switching with –/+ dial)
Check the operation of SD RAM for lip sync adjust
XXXXX: PASS (OK) or ERROR (NG)
The flash memory is updated by way of 232C
When the update is executed, the [MEMORY/ENTER] is pressed
The flash memory is updated by way of 1394
When the update is executed, the [MEMORY/ENTER] is pressed
XX: YES or NO
The destination is discriminated, and model name and AAC
correspondence/non-correspondance are written in i.LINK system
controller
Status of the i.LINK system controller is displayed
Enter the test mode when the [MEMORY/ENTER] is pressed
XX: Gain control value of brighness (00 to 1F)
(switching with –/+ dial)
XX: Gain control value of color difference (Cb) (00 to 1F)
(switching with –/+ dial)
XX: Gain control value of color difference (Cr) (00 to 1F)
(switching with –/+ dial)
Remark