Makita 1923H Instruction Manual
Hide thumbs
Also See for 1923H:
- Instruction manual (49 pages) ,
- Instruction manual (32 pages) ,
- Instruction manual (13 pages)
Related Manuals for Makita 1923H
Summary of Contents for Makita 1923H
- Page 1 Power Planer MODEL 1923H 004878 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
-
Page 2: Specifications
AC supply. They EEC, 89/336/EEC, 98/37/EC. are double-insulated in accordance with European Yasuhiko Kanzaki CE 2003 Standard and can, therefore, also be used from sockets without earth wire. Director MAKITA INTERNATIONAL EUROPE LTD. Michigan Drive, Tongwell, Milton Keynes, Bucks MK15 8JD, ENGLAND... -
Page 3: Safety Instructions
SAFETY INSTRUCTIONS ENA001-2 WARNING: When using electric tools, basic safety precautions, including the following, should always be followed to reduce the risk of fire, electric shock and personal injury. Read all these instructions before operating this product and save these instructions. For safe operations: tion and changing accessories. - Page 4 Make sure the blade is not contacting the work- 16. Wait for complete run-down before putting the piece before the switch is turned on. tool aside. Wait until the blade attains full speed before cut- 17. Use only Makita blades specified in this manual. ting. SAVE THESE INSTRUCTIONS...
-
Page 5: Functional Description
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Adjusting depth of cut 004879 Depth of cut may be adjusted by simply turning the knob on the front of the tool. - Page 6 • Use only the Makita wrench provided to remove or install the blades. Failure to do so may result in overtightening or insufficient tightening of the installation bolts. This could cause an injury.
- Page 7 002556 1. Inside edge of gauge plate 2. Blade edge 3. Planer blade 4. Adjusting plate 5. Screws 6. Heel 7. Back side of gauge base 8. Gauge plate 9. Gauge base For tool with mini planer blades Remove the existing blade, if the tool has been in use, carefully clean the 004887 drum surfaces and the drum cover.
-
Page 8: Correct Setting
Slip the heel of the adjusting plate into the groove of the drum. 002566 Set the drum cover over the adjusting plate/set plate and screw in the three hex flange head bolts so that a gap exists between the drum and the set plate to slide the mini planer blade into position. -
Page 9: Operation
004902 For European countries and areas When you wish to perform clean planing operation, connect a Makita vacuum cleaner to your tool. Install the nozzle on the tool using the screws. Then con- nect a hose of the vacuum cleaner to the nozzle as shown in the figures. - Page 10 Shiplapping (Rabbeting) 002580 To make a stepped cut as shown in the figure, use the edge fence (guide rule). Draw a cutting line on the workpiece. Insert the edge fence into the hole in the 004898 front of the tool. Align the blade edge with the cutting line. 1.
-
Page 11: Maintenance
Chamfering 003634 To make a chamfering cut as shown in the figure, align the “V” groove in the front base with the edge of the workpiece and plane it. 004901 1. “V” groove MAINTENANCE CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. - Page 12 First, loosen the two wing nuts on the holder and insert the blades (A) and (B), 002589 so that they contact the sides (C) and (D). Then tighten the wing nuts. 1. Wing nut 2. Blade (A) 3. Blade (B) 4.
- Page 13 CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
- Page 14 Memo...
- Page 15 Memo...
- Page 16 Makita Corporation 883522H3...