H8170 Parts Breakdown - Main Assembly ... 20 H8170 Parts List ... 21 H8171 Parts Breakdown - Main Assembly ... 22 H8171 Parts List ... 23 H8170/H8171 Parts Breakdown ... 24 Motor Assembly ... 24 H8170/H8171 Safety Label Parts List ... 25 WARRANTY AND RETURNS ... 26...
INTRODUCTION Foreword We are proud to offer the Model H8170/H8171 Hydraulic/Electric Log Splitter. This machine is part of a growing Grizzly family of fine household equipment. When used according to the guide- lines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satis-...
Figure 1. H8170/H8171 identification front view. A. Oil Tank B. Log Pusher C. Log Table D. Splitting Wedge E. Front Lifting Handle Support Leg G. Log Table Extension H. Power Switch Motor Wiring Box K. Wheel Rear Lifting Handle M. Hydraulic Control Lever N.
7. REGULARLY CHECK THE HYDRAULIC FLUID LEVEL AND ADD FLUID WHEN NEEDED. H8170/H8171 Hydraulic/Electric Log Splitter Log Splitters 8. NEVER USE THE LOG SPLITTER FOR CHANGE ANY PURPOSE OTHER THAN SPLITTING PRESSURE WOOD.
DO NOT connect the machine to the power source until instructed to do so. Amperage Draw The Model H8170/H8171 motor draws the follow- ing amps under maximum load: Motor Draw ... 13 Amps Circuit Recommendations...
H8170/H8171 Hydraulic/Electric Log Splitter Items Needed for The following items are needed to complete the setup process, but are not included with your machine: Description •...
Refer to the Machine Data Sheet for the dimensions of your splitter. Moving the Splitter The wheels on the Model H8170/H8171 make it possible for one person to move it short distances. However, the rugged design of your splitter makes it heavy;...
Use the carriage bolts and nuts to secure the support leg to the splitter body as shown in Figure 5. Figure 5. Attaching the support leg. H8170/H8171 Hydraulic/Electric Log Splitter Test Run Before you begin operations, do Steps 1–5 below to make sure your splitter is running properly.
OMMEND that you read books, trade maga- zines, or get formal training before begin- ning any projects. Regardless of the con- tent in this section, Grizzly Industrial will not be held liable for accidents caused by lack of training. -12- When you press the ON button, the electric mo- tor pressurizes hydraulic fluid.
ON position after the ram stops. Clear the pieces of split wood away from the splitter. H8170/H8171 Hydraulic/Electric Log Splitter Removing a Jammed If a log does not split and becomes jammed on the splitting wedge, DO NOT try to clear it by hit- ting it from the side or kicking it;...
-14- Checking/Adding Hydraulic Fluid The oil fill plug on the Model H8170/H8171 has a dipstick attached. The fill plug is located under the bleed screw on the back of the splitter. To check the fluid level: Use the front lifting handle to raise the split- ter to a vertical position, motor end up.
Always wear safety gog- gles when the changing hydraulic fluid. H8170/H8171 Hydraulic/Electric Log Splitter To change the hydraulic fluid: DISCONNECT THE SPLITTER FROM THE POWER SOURCE! With the help of an assistant, tip the splitter...
Always wear protective, gloves when sharpening the splitting wedge. During the life of your log splitter, you will need to sharpen the splitting wedge perodically. When sharpening the wedge,m keep in mind that if you try and keep the wedge sharpened to a razor point (like an axe blade), you will greatly reduce the life of the wedge by always sharpening it.
1. Debris lodged in the ram return path or in retract properly. the return springs. 2. Damaged seals in hydraulic system. H8170/H8171 Hydraulic/Electric Log Splitter Troubleshooting Possible Solution 1. Test for good contacts; correct the wiring. 2. Ensure hot lines have correct voltage on all legs and main power supply is switched ON.
H8170/H8171 Hydraulic System Schematic Before servicing the hydraulic system always disconnect the motor from power, and depressurize the hydraulic system by moving the control lever back and fourth a few times. Ignoring this warning can lead to hydraulic fluid poisoning, which is a serious and potentially fatal injury.
MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels. H8170/H8171 Hydraulic/Electric Log Splitter ��...
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.