Troubleshooting ... 22 Hydraulic System Schematic ... 23 Hydraulic and Chassis Diagram ... 24 Parts List ... 25 Safety Label Placement & Parts List ... 26 WARRANTY AND RETURNS ... 27 Model G0639 22-Ton Hydraulic Log Splitter Table of Contents...
INTRODUCTION Foreword We are proud to offer the Model G0639 22-Ton Hydraulic Log Splitter. This machine is part of a growing Grizzly family of fine equipment. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s com-...
Hydraulic Cylinder Bore ... 4" Dia Hydraulic Cylinder Stroke ... 24" Control Valve/Cylinder Operation ... Power Splitting, Neutral, and Power Retracting Filter Type ... Reusable Tank Screen Tank Type ... Vented Model G0639 22-Ton Hydraulic Log Splitter MACHINE DATA SHEET MODEL G0639 Data Sheet...
Page 6
Country Of Origin ... China Warranty ... 1 Year Serial Number Location ...ID Label on Hydraulic Cylinder Assembly Time ... 1.5 Hrs. Features: Heavy Duty Construction Power Splitter Retract 24" Splitting Stroke 22-Ton Splitter Load Model G0639 22-Ton Hydraulic Log Splitter...
Figure 1. G0639 identification front view. A. 2" Tow Ball Receiver B. 4" Hydraulic Cylinder Assembly C. Transfer Hose D. Control Lever and Valve E. High Pressure Hydraulic Line Splitter Wedge G. Low Pressure Hydraulic Return Line H. Log Cradle...
13. MACHINE LOCATION. Never leave the split- ter unattended and running, always block the wheels to prevent rolling, and store the unit in a locked location. Model G0639 22-Ton Hydraulic Log Splitter...
Model G0639 22-Ton Hydraulic Log Splitter Items Needed for The following items are needed to complete the setup process, but are not included with your machine: users.
Tow Ball Receiver ... 1 Front Landing Leg ... 1 K. Breakaway Safety Chains with Hooks ... 2 Figure 2. G0639 main parts inventory. Hardware Bag Contents (Figure 3): Hub Caps (Wheels) ... 2 M. Flat Washers 20mm (Wheels) ... 2 N.
Figure 7. Figure 7. Fender installation. Bolts The Model G0639 log splitter is not designed to be towed on logging roads, forest ser- vice roads, public roads, or highways. This machine is designed for job site towing only where maximum speed will not exceed 12 MPH.
Page 14
Hinge Pin and Cotter Pin Figure 10. Beam and cylinder hinge pin. 14. Lock the beam in place in the horizontal posi- tion with the spring loaded lock pin shown in Figure 11. Figure 11. Beam lock. Model G0639 22-Ton Hydraulic Log Splitter...
Page 15
Figure 13. Mounting Flange and Hex Bolt Figure 13. Installed engine. Model G0639 22-Ton Hydraulic Log Splitter 18. Wrap the pressure-fitting pipe threads with Teflon tape as shown in Figure 14. O-ring Figure 14.
Page 16
30. Refer to the Briggs & Stratton owner's manual to select your required oil type, locate the fill plug (Figure 19), and fill the engine with the required engine oil. Engine Oil Fill Plug Figure 19. Engine oil fill plug. Model G0639 22-Ton Hydraulic Log Splitter...
Refer to Troubleshooting on Page 22 for solutions, or call Technical Support at (570) 546-9663. Model G0639 22-Ton Hydraulic Log Splitter This machine presents serious injury hazards to untrained users. Read through this entire man- ual and the Briggs &...
OMMEND that you read books, trade maga- zines, or get formal training before begin- ning any projects. Regardless of the con- tent in this section, Grizzly Industrial will not be held liable for accidents caused by lack of training. -16-...
Model G0639 22-Ton Hydraulic Log Splitter Control Valve When the engine is running and the control valve lever is in the neutral position (Figure 20), the hydraulic pump delivers hydraulic fluid at 8 GPM...
Splitter Wedge Cradle Work Zone is Approximately a 6-Foot Sphere Rear Landing Leg and Lock Pin Figure 21. Log splitter positions. Model G0639 22-Ton Hydraulic Log Splitter Beam Safety Chain...
• Refer to the Briggs & Stratton engine manual for general engine maintenance schedules. Model G0639 22-Ton Hydraulic Log Splitter Checking/Adding Hydraulic Fluid To check the hydraulic fluid level: Position the log splitter on level ground, lower the front landing leg, and lock the leg in place.
10. Reinstall the tank screen, rubber gasket, and hose. 11. Fill the tank with 2.5 gallons of hydraulic fluid and reinstall the tank vent cap. Model G0639 22-Ton Hydraulic Log Splitter...
The optimum point is somewhere between. Refer to Figure 25 for a general idea. Model G0639 22-Ton Hydraulic Log Splitter leather Figure 25. Wedge points. ���������������...
4. Replace valve, flush and service hydraulic system. 5. Replace ram assembly, and flush and service sys- tem. 1. Repair bent or warn linkage to provide full travel. 2. Replace control valve. 3. Replace ram assembly. Model G0639 22-Ton Hydraulic Log Splitter...
��������������������� ������������������������������� Model G0639 22-Ton Hydraulic Log Splitter This hydraulic schematic will help you iden- tify hydraulic system components. However, it is not intended to be a how-to repair guide.
MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels. -26-...
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.