INTRODUCTION Foreword We are proud to offer the Model H8259 10" x 18" Benchtop Lathe. This machine is part of a grow- ing Grizzly family of fine woodworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s com-...
E. Tool Rest Lock Handle Tool Rest Base Release Lever G. Live Center H. Quill Lock Handle Quill Handwheel Tailstock H8259 10" x 18" Benchtop Lathe Identification Figure 1. Model H8259 Identification. K. Tool Rest Base Side Access Cover M. Leveling Foot N.
Use this and other machinery with caution and respect. Failure to do so could result in serious per- sonal injury, damage to equipment, or poor work results. H8259 10" x 18" Benchtop Lathe...
DO NOT connect the machine to the power source until instructed to do so. Amperage Draw The Model H8259 motor draws the following amps under maximum load: Motor Draw ... 3.5 Amps Circuit Recommendations...
-10- The Model H8259 was carefully packed when it left our warehouse. If you discover the machine is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice.
This natural, citrus-based degreaser is a great solution for removing export grease, and it’s much safer to work around than nasty solvents. Figure 4. Grizzly citrus degreaser. H8259 10" x 18" Benchtop Lathe Site Considerations Workbench Load Refer to the Machine Data Sheet for the weight and footprint specifications of your machine.
The switch disabling feature is not working. This safety feature must work properly before proceeding. Call Tech Support for help. —If the machine does not start, the switch disabling feature is working. Test Run H8259 10" x 18" Benchtop Lathe...
OMMEND that you read books, trade maga- zines, or get formal training before begin- ning any projects. Regardless of the con- tent in this section, Grizzly Industrial will not be held liable for accidents caused by lack of training. H8259 10" x 18" Benchtop Lathe...
Page 16
Figure 12, then tighten belt tension lever screw. ���������� Figure 12. Belt deflection. Tighten the motor mount screw. Replace the rear and side covers and tighten the cover knobs. ��� ���� ���� ���� ��� ��� ������ ������ H8259 10" x 18" Benchtop Lathe...
Rotate the quill handwheel clockwise until the tailstock quill protrudes out of the tailstock housing about ⁄ Insert the live center, as shown in Figure 17, and push firmly. H8259 10" x 18" Benchtop Lathe Spur Center...
Page 19
2'' or the quill will not be supported enough. Failure to follow these warnings may result in personal injury. H8259 10" x 18" Benchtop Lathe Removing/Installing To remove faceplate: UNPLUG LATHE FROM POWER!
Specialty Tools—These are the unique, special function tools to aid in hollowing, bowl making, cutting profiles, etc. The Swan Neck Hollowing Tool shown on Page 23 is a good example of a specialty tool. H8259 10" x 18" Benchtop Lathe...
������ Figure 24. Workpiece marked diagonally from corner to corner to determine the center. H8259 10" x 18" Benchtop Lathe Using a wood mallet, tap the point of the spur center into the center of the workpiece, so that it leaves a center mark, then remove the spur center.
Cut off the corners of the workpiece. Center the faceplate on the workpiece and attach it through the faceplate holes with non-tapered head wood screws as shown in Figure 28. Thread the faceplate onto the headstock spindle and tighten securely. H8259 10" x 18" Benchtop Lathe...
H8259 10" x 18" Benchtop Lathe Sanding/Finishing After turning, the workpiece can be sanded, as shown in Figure 30, and finished (in the same manner) before removing it from the lathe.
• Clean/vacuum dust buildup off of motor. Cleaning Cleaning the Model H8259 is relatively easy. Vacuum excess wood chips and sawdust, and wipe off the remaining dust with a dry cloth. If any resin has built up, use a resin dissolving cleaner to remove it.
Open the side and rear access covers as shown in Steps 1-5 in the Changing Speeds procedure on Page 13. Roll the belt off of the motor (lower) pulley (Figure 36). Figure 36. Belt removed from lower pulley. -24- H8259 10" x 18" Benchtop Lathe...
2. Belt cover bent or dented and is making speed is changed. contact with the motor pulley or belt. H8259 10" x 18" Benchtop Lathe Troubleshooting Possible Solution 1. Test for good contacts; correct the wiring. 2. Ensure hot lines have correct voltage on all legs and main power supply is switched ON.
Page 28
2. Apply less clamping pressure with tailstock. 3. Clean bed surface to remove oil/grease. 1. Turn the barrel handwheel until it forces taper out of barrel. Always make sure that taper surfaces are clean. H8259 10" x 18" Benchtop Lathe...
MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels. -30-...
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.