Advertisement
Quick Links
Cordless Driver Drill
Capacities
Steel
Wood
Wood screw
Machlne screw
I
I
Equipped with Electric Brake
MODEL 6 2 1 2 D
MODEL 6212DW
With Fast Charger
MODEL 6212DWG
With Fast Charger
Dimensions
Net
No load speed IRPM)
High
tow
It
x
W x
HI
weight
INSTRUCTION MANUAL
I
Battery Cartridge 1201
I
1201A
Voltage
12
v
SPECIFICATIONS
Model 6212D
Model DC1201 Fast Charger
Input
output
Charging time
A.C. only 50 Hz
-
60 Hz
D.C. 7.2 V
-
12 V
1 Hr.
10 mm
21 mm
6.4 mm
x 55
mm
1,150
-
370
237 mm x 79"
x 233 mm
1.8 kg
(318")
1
(13/16'1
I
(114" x 2-3/16")
I
6 m m 11'4"1
1
1
19-318" x 3-118" x 9-114")
I
13.7
Ibs)
I
Advertisement
Related Manuals for Makita 6212D
Summary of Contents for Makita 6212D
- Page 1 Cordless Driver Drill Equipped with Electric Brake MODEL 6 2 1 2 D MODEL 6212DW With Fast Charger MODEL 6212DWG With Fast Charger INSTRUCTION MANUAL SPECIFICATIONS Model 6212D Capacities No load speed IRPM) Dimensions High weight Steel Wood Wood screw...
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. -
Page 3: Polarized Plugs
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning AVOID UNINTENTIONAL STARTING. Don’t carry tool w i t h finger on switch. Be sure switch is OFF when plugging in. EXTENSION CORDS. -
Page 4: Voltage Warning
VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle, outlet, etc.1 be sure the voltage supplied is the same that specified o n the nameplate of the tool. power source w i t h voltage greater than that specified SERIOUS INJURY for the tool can result in t o the user... - Page 5 Before using battery charger, read all instructions and cautionary markings ( I 1 battery charger, battery, and product using battery. CAUTION - To reduce risk of injury, charge only MAKITA Battery Cartridge 1200 & 1201. Other types of batteries may burst causing personal injury and damage.
- Page 6 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle.
- Page 7 *After charging, unplug the charger from the power source. CAUTl ON *The fast charger Model DC1201 is for charging Makita battery cartridge. Never use it for other purposes or for other manufacturer’s batteries. When you charge a new battery cartridge or battery cartridge which has not been used for a long period of time, it may not accept a full charge.
- Page 8 If you charge battery cartridge from just-operated tool or a battery cartridge which has been left in location exposed to direct sunlight or heat for a long time, the charg- ing light may flash in red color. If this occurs, wait for while.
- Page 9 Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop. CAUTION : Before inserting the battery cartridge into the tool, always check to that the switch trigger actuates properly and returns to the "OFF"...
- Page 10 Adjusting fastening torque The fastening torque can be adjusted in six Drill marking stages by turning the adjusting ring so that the pointer on the adjusting ring points to number on the tool body. The fastening torque i s minimum when the pointer points t o the number 1 and maximum when it ‘...
- Page 11 Drilling operation First, turn the adjusting ring so that the pointer on the adjusting ring points to the . I \ - marking. Then proceed follows. Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with guide screw.
-
Page 12: Maintenance
Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. - Page 13 ACCESSORIES CAUTION: tool These accessories or attachments are recommended for use with your Makita specified in this manual. The use any other accessories or attachments might present a risk injury persons. The accessories or attachments should be used only in the proper and intended manner.
- Page 14 Sep - 0 8 - ' 9 4 CORDLESS DRIVER DRILL Model 6212D Note: The switch and other part configurations may differ from country to country.
- Page 15 MACHINE MACHINE Flat Washer 16 Housing Set [With Item Gear Spur Name Plate Spur Gear 1 5 Pan Head Screw M4x22 [With Washer1 Spur Gear 1 5 Tapping Screw BT4x20 Internal Gear 48 Hand Strap Flat Washer 18 Set Plate DC Motor Switch Sponge 14-72...
- Page 16 COMPLETE Ce&rs. If insp&tion shows tod, freight prepaid, Makita's Factdry or Akhorized &&e the trouble is caused by defective workmanship o r matenal, Makita will repair (or our option, replace) without charge. This Warranty not apply where: does repairs have been made or attempted by others.