Frameless Cabinets - GE ZET1 Installation Instructions Manual

Single Oven Cutout
A4
for Installation Over
a Monogram Warming
Drawer
27 5/16"
(69.2 cm)
Max.
9" (22.9 cm)
9 1/4"
Max.
(23.5 cm).
1" (2.5 cm) Min. Above Toekick or
Adjust to Oven Installation Height
NOTE: Additional clearances between cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior 23 1/2"
(59.7 cm) depth and 9 1/4" (23.5 cm) height.
• These Monogram Ovens require 3/4" (1.9
cm) overlap on both sides. Allow 1" (2.5 cm)
Min. for top overlap and clearance to upper
doors.
Cutout for Frameless Cabinets
A6

Frameless Cabinets

Whenever possible, order 30" (76.2 cm)
frameless cabinet with the cutout sided to fit
the oven. If using stock cabinets, additional
finished filler pieces may be required to
cover the opening.
• A stock frameless cabinet cutout width
may be up to 28 3/4" (73 cm). If necessary,
add 1/2" (1.3 cm) cleats to the sides, flush
with the front edge of the side panels to
accept mounting screws.
Cabinetry
23 1/2"
(59.7 cm)
Min.
Inside
2" x 2" (5 cm x 5 cm) or
2" x 4" (5 cm x 10 cm)
Anti-Tip Block Against
Rear Wall, 9" (22.9 cm)
From Floor to Bottom
of Block
2" (5.1 cm)
NOTE: Install the
Min.
oven only with
Allow 5/8"
specific models
(1.5 cm)
listed on the label
28 1/2"
Overlap
(72.4 cm).
located on top of
on All
the oven.
Sides
Double Oven Cutout
A5
for Installation Over
a Monogram Warming
Drawer
51 15/16"
(131.8 cm)
Max.
9" (22.9 cm)
Max.
1" (2.5 cm) Min. Above Toekick
• The Monogram Warming Drawers require
5/8" (1.6 cm) overlap on all sides.
• When installing a Monogram Warming
Drawer below a single or double oven, a
separate 120V, 60 Hz, properly grounded
receptacle must be installed. Refer to
installation instructions packed with the
Warming Drawer for specific installation
requirements.
Install 1/2"
(1.3 cm)
Cleats to
Hold Oven
Mounting
Screws
Double
51 15/16" (131.8 cm)
Single
27 5/16" (69.2 cm)
8
23 1/2"
(59.7 cm)
Min.
Inside
2" x 2" (5 cm x
5 cm) or 2" x
4" (5 cm x 10
cm) Anti-Tip
Block Against
Rear Wall, 9"
(22.9 cm)
From Floor
to Bottom
of Block
2" (5.1 cm)
Min.
9 1/4"
Allow 5/8"
(23.5 cm).
(1.5 cm)
Overlap
on All
Sides
28 1/2"
(72.4 cm)
30"
(76.2 cm)
Cabinet Depth
28 1/2" (72.4 cm)
23 1/2" (59.7 cm)
Min.
Min. From Inside
28 5/8" (72.7 cm)
Back to Front of
Max.
Cabinet Frame
or Side Panel
3/4" (1.9 cm) Min.
Thick Bottom Shelf
Cut Back Flush
with Front of
Side Panel