Philips CE120/55 Installation & Connection Manual

Register your product and get support at
EN Installation/Connection Guide
© 2008 Koninklijke Philips Electronics N.V.
All rights reserved.
CE120
1
a b
c
e
g
English
a Carry case with front panel stored inside
b Trim plate
These instructions are for a typical installation.
However, if your car has different requirements, c Standard connector
make the corresponding adjustment. If you have
d Disassembly tool x 2 pcs
any questions regarding installation kits, consult
your Philips car audio dealer.
e Rubber cushion
f Screw x 4 pcs
Caution
g Mounting bolt
This unit is designed for negative ground
•
(earth) 12 V DC operation only.
Connect wires: ISO connectors
• Always install this unit in the car dashboard.
Other locations can be dangerous as the
rear of the unit heats up during use.
To avoid short-circuit: before you connect,
•
Caution
ensure that the ignition is off.
• Ensure that you connect the yellow and red
• Ensure that all loose leads are insulated with
power supply leads after all other leads are
electrical tape.
connected.
Ensure that all loose leads are insulated with
•
1
electrical tape.
Pull out the ISO connectors from car dash-
• Ensure that the leads do not get caught
board and connect them to the bigger end
under screws orin parts that will move (e.g.
of the supplied standard connector.
seat rail).
2
Connect the other end of the supplied
Ensure that all ground (earth) leads are run
•
standard connector to the unit.
to a common ground (earth) point.
3
Do the other connections, if applicable.
• Use only the supplied mounting hardware
for a safe and secure installation.
1
Antenna
• Improper fuses can cause damage or fi re.
When you need to change the fuse, consult
2
Rear line out
a professional.
(right)
3
Rear line out
Note on the power supply lead (yellow)
(left)
• When you connect other devices to this
unit, ensure that the rating of the car circuit
is higher than the total fuse value of all the
Connect wires: without ISO
connected devices.
connectors
Notes on speaker connection
• Never connect speaker wires to the metal
body or chassis of the car.
Caution
• Never connect speaker wires with stripes to
Ensure that all loose leads are insulated with
one another. •
electrical tape.
Overview of parts
1
Cut off the bigger end of the supplied
standard connector.
These are the supplied parts needed to connect
2
Check the car's wiring carefully and connect
and install this unit.
them to the supplied standard connector.
2a
d
2b
f
1
Black To a metal surface of the
car
First connect the black
ground (earth) lead, then
connect the yellow and red
power supply leads.
2
Blue To the electric antenna
control lead or power
supply lead of the antenna
booster
If there is no electric an-
tenna or antenna booster,
or it is manually operated
telescopic antenna, it is not
necessary to connect this
lead.
3
Yellow To the +12V car battery
which is energized at all
times.
4
Pink To telephone mute termi-
nal (if any).
5
Red To the +12V power termi-
nal which is energized in
the accessory (ACC) posi-
tion of the ignition switch
If there is no accessory po-
sition, connect to the +12V
car battery terminal that
To antenna
is always live. Be sure to
connect the black ground
To amplifi er line
(earth) lead to a metal
in (right)
surface of the car fi rst.
To amplifi er line
6
Green/ Left speaker (Rear)
in (left)
black
strip
7
White/ Left speaker (Front)
black
strip
8
Gray/ Right speaker (Front)
black
strip
9
Purple/ Right speaker (Rear)
black
strip
3
Connect the supplied standard connector to
the unit.
9 1
2
3
8
4
5
7
6
4 6
Reconnect the negative terminal of the car
Do the other connections, if applicable.
battery.
1
Antenna To antenna
Detach the front panel
2
Rear line out To amplifi er
(right) line in (right) You can detach the front panel to deter theft.
1
3 Press to release the panel.
Rear line out To amplifi er
2
Pull the panel towards you to detach it from
(left) line in (left)
the chassis.
3
Store the panel in the supplied carry case to
protect it from dirt or damage.
Attach the front panel
1
Attach the trim plate.
Replace fuse
2
Insert the left side of the panel in the chassis
until it is correctly engaged.
If there is no power, the fuse may broke and need
to be replaced.
3
Press the right side of the panel until it is
1
locked into place. Detach the front panel and take out the unit.
(see 'Remove the unit' on page 23)
2
Check the electric connection .
Mount into the dashboard 3
Buy a fuse that matches the voltage of the
damaged fuse (15A)
1
Ensure that car dashboard opening is within
4
Replace the fuse.
these measurements:
If the fuse is broken again after replacement, there
• If the car dashboard is bigger, the sup-
might have internal malfunction. In such case,
plied mounting sleeve is not suitable for
consult your Philips dealer.
the car. Remove the mounting sleeve
with the removal keys and consult a
professional for advice.
Remove the unit
2
If the car does not have an on-board drive
or navigation computer, disconnect the nega-
To repair or replace the unit, remove it from the
tive terminal of the car attery.
dashboard.
• If you disconnect the car battery in
1
Detach the front panel.
a car that has an on-board drive or
2
navigation computer, the computer may Pull out the unit by using the removal keys.
lost its memory.
• If the car battery is not disconnected,
to avoid short-circuit, ensure that bare
wires do not touch each other.
3
Connect the supplied mounting bolt to the
unit.
4
Place the supplied rubber cushion over the
end of the mounting bolt.
5
Slide the unit into the dashboard until you
hear a click sound.
3 2 1