Philips CE120/55 Quick Start Manual

Register your product and get support at
ENG Quick Start Guide
N.V. Electronics Philips
CE120
1
a b
c
e
g
English
reserved. rights All 1 Black
Koninklijke 2008 ©
Overview of parts
These are the supplied parts needed to connect
2
Blue
and install this unit.
a Carry case with front panel stored inside
b Trim plate
c Standard connector
d Disassembly tool x 2 pcs
e Rubber cushion
3 Yellow
f Screw x 4 pcs
4
Pink
g Mounting bolt
5 Red
Connect wires: ISO connectors
1
Pull out the ISO connectors from car
dashboard and connect them to the bigger
end of the supplied standard connector.
2
Connect the other end of the supplied
standard connector to the unit.
3
Do the other connections, if applicable. 6 Green/
black
1 Antenna To antenna
strip
7 White/
2 Rear line out To amplifi er line in (right)
black
(right)
strip
3
Rear line out To amplifi er line in (left)
8 Gray/
(left)
black
strip
Connect wires: without ISO
connectors
9
Purple/
black
1
Cut off the bigger end of the supplied
strip
standard connector.
3
2
Check the car's wiring carefully and connect Connect the supplied standard connector to
them to the supplied standard connector.
the unit.
4
Do the other connections, if applicable.
2a
d
2b
f
To a metal surface of the car 1 Antenna To antenna
First connect the black ground
2 Rear line out To amplifi er line
(earth) lead, then connect the
(right) in (right)
yellow and red power supply
leads.
3 Rear line out To amplifi er line
To the electric antenna control
(left) in (left)
lead or power supply lead of the
antenna booster
If there is no electric antenna or
antenna booster, or it is manually Attach the front panel
operated telescopic antenna, it
is not necessary to connect this 1
Attach the trim plate.
lead.
2
Insert the left side of the panel in the chassis
To the +12V car battery which until it is correctly engaged.
is energized at all times .
3
Press the right side of the panel until it is
To telephone mute terminal (if
locked into place.
any) .
To the +12V power terminal
which is energized in the ac-
Mount into the dashboard
cessory (ACC) position of the
ignition switch
If there is no accessory position, Note
connect to the +12V car battery
• Check wire connection before you mount the
terminal that is always live. Be
unit into a car.
sure to connect the black ground
• If preset radio stations are lost when the
(earth) lead to a metal surface of
ignition key is turned OFF and then back ON,
the car fi rst.
reconnect the red leads crosswise to the
Left speaker (Rear)
yellow ones.
1
Ensure that car dashboard opening is within
Left speaker (Front)
these measurements:
• If the car dashboard is bigger, the sup-
plied mounting sleeve is not suitable for
Right speaker (Front)
the car. Remove the mounting sleeve
with the removal keys and consult a
professional for advice.
2
If the car does not have an on-board drive
Right speaker (Rear)
or navigation computer, disconnect the nega-
tive terminal of the car attery.
• If you disconnect the car battery in
a car that has an on-board drive or
navigation computer, the computer may
lost its memory.
• If the car battery is not disconnected,
to avoid short-circuit, ensure that bare
wires do not touch each other.
9
1
2
3
8
4
5
7
6
3 2
Connect the supplied mounting bolt to the Press DBB or SEARCH to select band:
unit.
[FM1] , [FM2] , [FM3] , [AM1] , or [AM 2] .
4 3
Place the supplied rubber cushion over the Press LOC/DX to select tuner sensitivity:
end of the mounting bolt.
[LOCAL] (local): Only station with strong
5
signal can be broadcast.
Slide the unit into the dashboard until you
hear a click sound.=
[DX] (distance): Stations with strong and
weak signals can be broadcast.
6
Reconnect the negative terminal of the car
4
battery.
Press or to tune to a radio station
manually.
The radio station is broadcast.
»
Detach the front panel
• To search for radio station automatically,
press or for 3 seconds.
You can detach the front panel to deter theft.
Insert USB device
1
Press to release the panel.
2
Pull the panel towards you to detach it from
1
Open the cover marked
the chassis.
panel.
3
Store the panel in the supplied carry case to
2
Insert the USB device into the USB socket.
protect it from dirt or damage.
The unit star ts playing from the USB
»
device automatically.
Turn on
1
Insert SD/MMC card
Press to turn on the unit.
• To turn off the unit, press for 3
1
seconds. Open the cover marked
panel.
Set clock
2
Insert the SD or MMC card into the card
slot.
1
Press MENU / DISP for 3 seconds.
The unit starts playing from the SD/MMC
»
2
Press DBB or SEARCH repeatedly until
card automatically.
the currently clock is displayed.
3
Turn in clockwise direction to set hour.
Control play
Turn in anti-clockwise direction to set
minute.
4
• To select a folder, press DBB or SEARCH
Press to confi rm.
.
• To skip to a track, press
View clock • To search within a track, press
3 seconds.
1
• To pause, press 1 , . To resume, press 1 ,
Press MENU / DISP repeatedly until the clock
again.
is displayed.
Tune to a radio station
1
Press SOURCE to select Tuner.
3 2 1
on the front
on the front
or .
or for