Philips CE120X/78 Quick Start Manual

Register your product and get support at
ENG Quick Start Guide
N.V. Electronics Philips
CE120
1
a b
c
e
g
English
reserved. rights All 1 Black
Koninklijke 2008 ©
Overview of parts
These are the supplied parts needed to connect
2 Blue
and install this unit.
a Carry case with front panel stored inside
b Trim plate
c Standard connector
d Disassembly tool x 2 pcs
e Rubber cushion
3 Yellow
f Screw x 4 pcs
4 Pink
g Mounting bolt
5 Red
Connect wires: ISO connectors
1
Pull out the ISO connectors from car
dashboard and connect them to the bigger
end of the supplied standard connector.
2
Connect the other end of the supplied
standard connector to the unit.
3
Do the other connections, if applicable. 6 Green/
black
1 Antenna To antenna
strip
7
2 Rear line out To amplifi er line in (right) White/
(right) black
strip
3 Rear line out To amplifi er line in (left)
(left) 8 Gray/
black
strip
Connect wires: without ISO
connectors
9 Purple/
black
1
Cut off the bigger end of the supplied
strip
standard connector.
3
2
Check the car's wiring carefully and connect Connect the supplied standard connector to
them to the supplied standard connector.
the unit.
4
Do the other connections, if applicable.
2a
d
2b
f
To a metal surface of the car 1 Antenna To antenna
First connect the black ground
2
Rear line out To amplifi er line
(earth) lead, then connect the
(right) in (right)
yellow and red power supply
leads.
3 Rear line out To amplifi er line
To the electric antenna control
(left) in (left)
lead or power supply lead of the
antenna booster
If there is no electric antenna or
antenna booster, or it is manually Attach the front panel
operated telescopic antenna, it
is not necessary to connect this 1
Attach the trim plate.
lead.
2
Insert the left side of the panel in the chassis
To the +12V car battery which
until it is correctly engaged.
is energized at all times .
3
Press the right side of the panel until it is
To telephone mute terminal (if
locked into place.
any) .
To the +12V power terminal
which is energized in the ac-
Mount into the dashboard
cessory (ACC) position of the
ignition switch 1
Ensure that car dashboard opening is within
If there is no accessory position,
these measurements:
connect to the +12V car battery
• If the car dashboard is bigger, the sup-
terminal that is always live. Be
plied mounting sleeve is not suitable for
sure to connect the black ground
the car. Remove the mounting sleeve
(earth) lead to a metal surface of
with the removal keys and consult a
the car fi rst.
professional for advice.
2
Left speaker (Rear)
If the car does not have an on-board drive
or navigation computer, disconnect the nega-
tive terminal of the car attery.
• If you disconnect the car battery in
Left speaker (Front)
a car that has an on-board drive or
navigation computer, the computer may
lost its memory.
Right speaker (Front)
• If the car battery is not disconnected,
to avoid short-circuit, ensure that bare
wires do not touch each other.
3
Connect the supplied mounting bolt to the
Right speaker (Rear)
unit.
4
Place the supplied rubber cushion over the
end of the mounting bolt.
5
Slide the unit into the dashboard until you
hear a click sound.=
6
Reconnect the negative terminal of the car
battery.
9 1
2
3
8
4
5
7
6
Detach the front panel Insert USB device
You can detach the front panel to deter theft. 1
Open the cover marked
1 panel.
Press to release the panel.
2 2
Pull the panel towards you to detach it from Insert the USB device into the USB socket.
the chassis.
The unit star ts playing from the USB
»
3 device automatically.
Store the panel in the supplied carry case to
protect it from dirt or damage.
Insert SD/MMC card
Turn on
1
Open the cover marked
1
Press to turn on the unit. panel.
• To turn off the unit, press for 3 2
Insert the SD or MMC card into the card
seconds.
slot.
The unit starts playing from the SD/MMC
Set clock »
card automatically.
1
Press MENU / DISP for 3 seconds.
2
Press DBB or SEARCH repeatedly until
Control play
the currently clock is displayed.
3
Turn in clockwise direction to set hour.
• To select a folder, press DBB or SEARCH
Turn in anti-clockwise direction to set
.
minute.
• To skip to a track, press
4
Press to confi rm. • To search within a track, press
3 seconds.
• To pause, press 1 ,
View clock again.
1
Press MENU / DISP repeatedly until the clock
is displayed.
Tune to a radio station
1
Press SOURCE to select Tuner.
2
Press DBB or SEARCH to select band:
[FM1] , [FM2] , [FM3] , [AM1] , or [AM 2] .
3
Press LOC/DX to select tuner sensitivity:
[LOCAL] (local): Only station with strong
signal can be broadcast.
[DX] (distance): Stations with strong and
weak signals can be broadcast.
4
Press or to tune to a radio station
manually.
The radio station is broadcast.
»
• To search for radio station automatically,
press or for 3 seconds.
3 2 1
on the front
on the front
or .
or for
. To resume, press 1 ,