Honeywell ADEMCO 6150RF Installation And Setup Manual page 6

Step Action
Enter [4] (Loop Functions). Enter the loop number (1-4).
6
Note: The 6150RF is shipped with the loop functions pre-
programmed. Perform steps 6 through 10 only if it is necessary
to change any of the loop functions.
Loop 1
Loop 2
Loop 3
Loop 4
See the Wireless Key Function Chart below for the choices.
Function
Disarming
Arming Away
Arming Stay
Arming Maximum (Away Instant)
Arming Instant
Panic Alarm
Produces type of alarm [* & #]
programmed in control panel.
Manually Start a Relay Action
Manually Stop a Relay Action
Activate Relay as Programmed in
Control
Activate Relay as Programmed in
Control
Activate Access Control Relay for
Partition
n = Device Number programmed in VISTA-20SE(HW) to be controlled
Press the [✱] key.
Repeat step 6 for the rest of the loops of the wireless key.
7
8 To program a button on the wireless key to control the on-board
relay, enter [5] (On-Board Relay Assignment).
9 Enter the loop number of the wireless key (1-4). Enter the relay
action (0 = no action; 1 = relay off; 2 = relay on; 3 = relay toggles on
and off; 4 = relay closes for 2 seconds).
Note: The relay action must be "0" for UL installations.
Press the [✱] key.
Repeat step 9 for the rest of the loops.
10
When all loops have been programmed for the wireless key, press
11
the [✱] key.
12 The 6150RF automatically displays the next available device
number (one that does not have a serial number).
If you want to program additional wireless keys, repeat steps 3
through 10. Otherwise, press the [#] key. This takes you back to the
main display, which alternately flashes "oo" and "- -."
Enter [0] (High Security Mode). To put the system into High-
13
Security mode, enter [1]. Enter [0] to disable.
Press [✱] to exit the 6150RF Program mode.
14
Note: Upon exiting the Program mode, the 6150RF alternately flashes "Ad," the 2-digit keypad address, and
the 2-digit receiver address. If either of these is incorrect, repeat steps 1 through 3 in the
Programming for an Installation Without Local Wireless Keys section.
- 6 -
Close the 6150RF On-Board Relay for 2 sec.
1 (Disarm)
2 (Arm Away)
3 (Arm Stay)
Wireless Key Function Chart
Entry
1
2
3
4
7
# + 99
# + 7 (VISTA-10P, VISTA-10SE,
VISTA-15, VIA-30PSE)
# + 7 + n (VISTA-20P, VISTA-
20SE(HW))
# + 8 (VISTA-10P, VISTA-10SE,
VISTA-15, VIA-30PSE)
# + 8 + n (VISTA-20P, VISTA-
20SE(HW))
# + 71 (VISTA-40, VISTA-50P,
VISTA-128B)
# + 72 (VISTA-40, VISTA-50P,
VISTA-128B)
0 (VISTA-40, VISTA-50P,
VISTA-128B)
Display
Flashes "Ln."
Once the loop number is
entered, alternately flashes
"L" with the loop number;
and the present function.
Default Loop Functions
Loop 3
Arm AWAY
Loop 2
Loop 4
Disarm
Arm STAY
Loop 1
Close on-board relay
for 2 seconds
5 8 0 4
Loop 2
Disarm
Loop 4
Arm STAY
Loop 3
Arm AWAY
Loop 1
Close on-board relay
for 2 seconds
• •
• •
• •
• • •
• • • •
• • • •
•
SET
•
HOUSE
CODE
5 8 0 4 B D / 5 8 0 4 B DV
Flashes "o-."
Flashing "o" and the loop
number.
Once the action is entered,
displays "o" and alternately
flashes the loop number and
the relay action.
Flashes "d" followed by the
device number.
En