1. Manuals
  2. Brands
  3. Grizzly Manuals
  4. Chippers/Shredders
  5. G0594
  6. Owner's manual

Grizzly G0594 Owner's Manual

Large chipper/shredder
Hide thumbs Also See for G0594:
Table of Contents

Advertisement

Quick Links

Download this manual
MODEL G0594
LARGE CHIPPER/SHREDDER
OWNER'S MANuAL
Copyright © NoVEMBEr, 2005 By grizzly iNdustrial, iNC. rEVisEd august, 2011 (Bl)
WARNING: NO PORtION Of tHIS MANuAL MAy bE REPRODuCED IN ANy SHAPE
OR fORM WItHOut tHE WRIttEN APPROvAL Of GRIzzLy INDuStRIAL, INC.
(For ModEls MaNuFaCturEd siNCE 7/11) #Ew7656 priNtEd iN ChiNa

Advertisement

Table of Contents
loading

Related Manuals for Grizzly G0594

Summary of Contents for Grizzly G0594

  • Page 1 MODEL G0594 LARGE CHIPPER/SHREDDER OWNER'S MANuAL Copyright © NoVEMBEr, 2005 By grizzly iNdustrial, iNC. rEVisEd august, 2011 (Bl) WARNING: NO PORtION Of tHIS MANuAL MAy bE REPRODuCED IN ANy SHAPE OR fORM WItHOut tHE WRIttEN APPROvAL Of GRIzzLy INDuStRIAL, INC.
  • Page 2 This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.

  • Page 3: Table Of Contents

    table of Contents Manual accuracy ........................2 Machine data sheet ........................2 Contact info ..........................2 identification ..........................3 SECtION 1: SAfEty ........................4 safety instructions for Machinery ....................4 additional safety instructions for Chipper/shredders ..............6 SECtION 2: SEtuP ......................... 7 unpacking ..........................

  • Page 4: Manual Accuracy

    Where could it be improved? For your convenience, we post all available docu- Please take a few minutes to give us feedback. mentation on our website at www.grizzly.com. Any updates to this document will be reflected on Grizzly Documentation Manager our website as soon as complete.

  • Page 5: Identification

    Identification Machine Identification (figures 1 & 2) A. hopper b. Motor C. Chip outlet D. Chipper Funnel E. Choke gas Cap G. throttle H. oN/oFF switch pull start handle gas shut off Valve K. Exhaust figure 1. Chipper/shredder identification. figure 2. Motor identification. Model G0594 (Mfg.

  • Page 6: Section 1: Safety

    SECtION 1: SAfEty For Your Own Safety, Read Instruction Manual Before Operating This Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor- tance of the safety messages.
  • Page 7 INTENdEd usAGE.­ Only­ use­ machine­ for­ its­ machine­ in­ good­ working­ condition.­ A­ machine­ intended­purpose­and­never­make­modifications­ that­ is­ improperly­ maintained­ could­ malfunction,­ ­ not­ approved­ by­ Grizzly.­ Modifying­ machine­ or­ leading­to­serious­personal­injury­or­death.­ using­ it­ differently­ than­ intended­ may­ result­ in­ ChECK dAMAGEd PARTs.­ Regularly­ inspect­...

  • Page 8: Additional Safety Instructions For Chipper/Shredders

    Additional Safety Instructions for Chipper/ Shredders READ MANuAL. read this entire manual and the OPERAtING LOCAtION. set up the chipper/ Briggs & stratton motor manual. these manuals shredder on firm, level, grass or dirt. do Not set ® contain proper operating and safety instructions for up the chipper/shredder on gravel, asphalt, con- this chipper/shredder.

  • Page 9: Section 2: Setup

    SECtION 2: SEtuP Site Considerations this machine presents serious injury hazards Location to untrained users. Read the chipper/shredder must be placed on a firm, through this entire manu- flat, grass or dirt surface to prevent the machine al to become familiar with from tipping.

  • Page 10: Inventory

    Inventory Assembly The following is a list of items shipped with your the major components of this chipper/shredder machine. Before beginning setup, lay these items have been assembled at the factory. some minor out and inventory them. assembly is required. the assembly process will use all the parts and hardware listed in the inven- If any non-proprietary parts are missing (e.g.
  • Page 11 gasket handle figure 5. hopper gasket positioned. place the hopper on top of the gasket and figure 7. location to install the handles. line up all of the holes. place two rubber grommets and 8mm fender washers on two place the funnel over the studs in the side M8-1.25 x 35 hex bolts, thread them through of the chipper/shredder and secure it with the holes nearest the motor, then secure...

  • Page 12: Section 3: Operations

    Regardless of the con- stop suddenly causing the chipper/shredder tent in this section, Grizzly Industrial will to fall over, or causing injury to your hand or not be held liable for accidents caused by arm.
  • Page 13 to shred twigs, leaves, and brush: to chip branches: slowly pour the material into the hopper. do stand to the side of the hopper and make Not try to stuff too much material in at one sure you have a stable stance and firm foot- time or the machine will jam.

  • Page 14: Section 4: Maintenance

    SECtION 4: MAINtENANCE Storage turn OFF the machine, allow all moving parts to come to a complete stop, and dis- Follow these guidelines when storing your chip- connect the spark plug wire before moving per/shredder. the machine, emptying the bag, unclogging the inlets or outlets, filling the gas tank, or •...

  • Page 15: Section 5: Service

    SECtION 5: SERvICE review the troubleshooting and procedures in this section to fix your machine if a problem develops. if you need replacement parts or you are unsure of your repair skills, then feel free to call our technical support at (570) 546-9663 for machine repairs, or contact Briggs &...

  • Page 16: Replacing Blades

    Replacing blades Replacing v-belt replace or tighten the V-belt if you notice the sharpen or replace the blades as soon as the motor running and the chipper blades are not chipping performance begins to deteriorate, or if spinning. you notice dings, chips, or cracks. tools Needed tools Needed adjustable wrench ..........

  • Page 17: Parts Breakdown

    Parts breakdown 62V2 74 75 -15- Model G0594 (Mfg. Since 7/11)

  • Page 18: Parts List

    MuSt maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels. -16-...

  • Page 19: Warranty And Returns

    WARRANty AND REtuRNS grizzly industrial, inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. this warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
  • Page 21 Would you recommend Grizzly Industrial to a friend? _____ Yes _____No Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than 3 times. _____ Yes _____No 10.
  • Page 22 FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ TAPE ALONG EDGES--PLEASE DO NOT STAPLE...

Table of Contents