Page 2
MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.
Contact Info ... 2 Identification ... 3 SECTION 1: SAFETY... 4 Safety Instructions for Machinery ... 4 Additional Safety Instructions for Chipper/Shredders ... 6 SECTION 2: SET UP ... 8 Set Up Safety ... 8 Unpacking ... 8 Site Considerations ... 8 Items Needed for Set Up ...
INTRODUCTION Foreword We are proud to offer the Model G0594 Large Chipper/Shredder. This machine is part of a grow- ing Grizzly family of fine machinery. When used according to the guidelines set forth in this manu- al, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to...
Figure 1. Chipper/shredder identification. G0594 Large Chipper/Shredder Identification Machine Identification (Figures 1 & 2) A. Hopper B. Motor C. Chip Outlet D. Chipper Funnel E. Choke Gas Cap G. Throttle H. ON/OFF Switch Pull Start Handle Gas Shut Off Valve K.
Wear protective hair covering to con- tain long hair and wear non-slip footwear. 6. NEVER OPERATE MACHINERY WHEN TIRED, OR UNDER THE INFLUENCE OF OPERATING DRUGS OR ALCOHOL. Be mentally alert at all times when running machinery. OPERATING MACHINERY. G0594 Large Chipper/Shredder...
Page 7
Follow instructions for lubricating and changing accessories. 16. MAKE SURE GUARDS ARE IN PLACE AND WORK CORRECTLY BEFORE USING MACHINERY. G0594 Large Chipper/Shredder 17. REMOVE WRENCHES. Make a habit of checking for keys and adjusting wrenches before turn- ing machinery ON.
DO NOT set up the chipper/shredder in a location where sparks or heat from the motor could cause a fire. G0594 Large Chipper/Shredder...
Page 9
If normal safety precautions are overlooked or ignored, seri- ous personal injury may occur. G0594 Large Chipper/Shredder 10. TURN OFF CHIPPER/SHREDDER: Turn OFF the machine, allow all moving parts to come to a complete stop, and discon-...
Unpacking The Model G0594 was carefully packed when it left our warehouse. If you discover the machine is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice.
Page 12
Before operating, fill the motor with oil and gas according to the instructions in the Briggs & Stratton manual. NOTICE This chipper/shredder does not have oil in the motor when shipped. Add oil before operating the chipper/shredder, or the motor will seize. G0594 Large Chipper/Shredder...
OMMEND that you read books, trade maga- zines, or get formal training before begin- ning any projects. Regardless of the con- tent in this section, Grizzly Industrial will not be held liable for accidents caused by lack of training. NOTICE This chipper/shredder does not have oil in the motor when shipped.
Page 14
Chipping wood when it is green is easier on the machine. The blades will stay sharper longer. • The chipper/shredder will work best if the blades are sharp. Rotate, sharpen, or replace the blades as soon as chipper/shredder per- formance begins to deteriorate. G0594 Large Chipper/Shredder...
Check the engine oil level. See the Briggs & Stratton motor manual for specifications. Cleaning Clean the Model G0594 after each use. Allow the motor to cool and remove the spark plug wire. Brush off or vacuum wood chips and wipe off the remaining dust from the exterior of the machine with a dry cloth.
G0594 Large Chipper/Shredder Replacing V-Belt Figure 12. Replacing V-belt. Loosen the idler pulley and roll the belt off of the pulleys (see Figure 12). Install the new belt and adjust the idler pulley so the V-belt deflects approximately pushed with moderate pressure.
MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels. G0594 Large Chipper/Shredder...
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.