Table Of Contents - Grizzly G0514X Owner's Manual

INTRODucTION ............................................... 2
Manual accuracy ........................................... 2
Contact info.................................................... 2
identification (g0514X) .................................. 3
identification
(g0514X2/g0514X2B/g0514X3) ................... 4
Machine data ................................................. 5
SEcTION 1: SAfETy ....................................... 7
safety instructions for Machinery .................. 7
additional safety for Bandsaws ..................... 9
SEcTION 2: pOWER SuppLy ...................... 10
g0514X3 440v Conversion ......................... 13
SEcTION 3: SETup ....................................... 14
needed for setup ......................................... 14
unpacking .................................................... 14
g0514X inventory ........................................ 15
g0514X2 & g0514X3 inventory .................. 16
g0514X2B ................................................... 17
hardware recognition Chart ....................... 18
Clean up ...................................................... 19
site Considerations ...................................... 19
Moving & placing Base unit ........................ 20
Mounting ...................................................... 21
assembly ..................................................... 21
Blade tracking ............................................. 23
positive stop ................................................ 25
dust Collection ............................................. 26
installing Fence ............................................ 26
(g0514X, -X2, X3) ....................................... 26
installing Fence (g0514X2B) ....................... 28
installing Foot Brake (g0514X2, -X3) .......... 28
g0514X, -X2, & X2B power Connection ..... 29
g0514X3 power Connection ....................... 29
test run ...................................................... 30
tensioning Blade ......................................... 31
adjusting support Bearings ......................... 32
adjusting Blade guide Bearings .................. 33
aligning table .............................................. 35
aligning Fence ............................................. 35
Fence pointer Calibration ............................ 36
Miter gauge ................................................. 36
SEcTION 4: OpERATIONS ........................... 37
Basic Controls .............................................. 37
operation overview ..................................... 39
Basic Cutting tips ........................................ 39
Workpiece inspection................................... 40
Foot Brake ................................................... 41
table tilt ...................................................... 41
guide post ................................................... 42

Table of contents

Fine tune tracking ...................................... 43
ripping ......................................................... 43
Crosscutting ................................................. 44
resawing ..................................................... 44
Cutting Curves ............................................. 45
stacked Cuts................................................ 46
Blade speed ................................................ 46
Blade information ......................................... 47
Blade Changes ............................................ 49
SEcTION 5: AccESSORIES ......................... 50
SEcTION 6: MAINTENANcE ......................... 52
schedule ...................................................... 52
Cleaning ....................................................... 52
unpainted Cast iron ..................................... 52
Brushes ........................................................ 52
lubrication ................................................... 52
SEcTION 7: SERvIcE ................................... 55
troubleshooting ........................................... 55
Checking v-Belt ........................................... 59
tensioning v-Belt......................................... 59
replacing v-Belt .......................................... 60
Blade lead ................................................... 61
adjusting Wheel Brush ................................ 62
adjusting tension lever .............................. 62
adjusting guide post travel ........................ 63
aligning Wheels ........................................... 65
SEcTION 8: WIRING ...................................... 68
Wiring safety instructions ............................ 68
g0514X Wiring diagram .............................. 69
g0514X2 Wiring diagram ............................ 70
g0514X2B Wiring diagram ......................... 71
g0514X3 Wiring diagram ............................ 72
SEcTION 9: pARTS ....................................... 73
g0514X Main ............................................... 73
g0514X Fence/guides ................................ 75
g0514X2 & g0514X3 Main ......................... 78
g0514X2 & g0514X3 Fence & guides ....... 81
g0514X2 & g0514X3 labels ...................... 84
g0514X2B Main........................................... 85
g0514X2B Fence & guides ........................ 87
g0514X2B labels ........................................ 90
WARRANTy AND RETuRNS ........................ 93