D-Link DCS-3415 Quick Installation Manual
18x poe network camera
Hide thumbs
Also See for DCS-3415:
- User manual (96 pages) ,
- Quick installation manual (25 pages) ,
- Datasheet (3 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for D-Link DCS-3415
Summary of Contents for D-Link DCS-3415
-
Page 2: Minimum System Requirements
Note: Using a power supply with a different voltage than the one included with your product will cause damage and void the warranty for this product. If any of the above items are missing, please contact your reseller. D-Link DCS-3415 Quick Install Guide... -
Page 3: Hardware Overview
Fast Ethernet cabling. This port cycle twice. supports the NWay protocol, allowing the network camera to automatically detect or negotiate the transmission DI/DO speed of the network. The DCS-3415 provides a general I/O terminal block. The I/O connectors provide the physical interface to The Ethernet port can also be used send and receive digital signals to and from a variety of to power the camera by using a external devices. PoE switch. DC12V output... -
Page 4: Front View
CF card slot CompactFlash (CF) is a mass storage device format used in portable electronic devices. The CF card slot can be seen at the side of the network camera. Note: Ensure to remove the rubber strip before using it. D-Link DCS-3415 Quick Install Guide... -
Page 5: Hardware Installation
Connect Using Power-Over-Ethernet Once you connect an Ethernet cable to your PoE switch or adapter, the Power LED on the DCS-3415 will turn green to indicate a proper connection. Attach the External Power Supply Attach the supplied power adapter to the DC power input connector located on the Network Camera’s back panel (labeled DC 12V) and... - Page 6 Hardware Installation The package comes with a camera stand with a swivel ball screw head that can be attached to the Network Camera’s bottom socket cavity. Attach the camera stand to the Network Camera and place it for your application. There are holes located in the base of the camera stand allowing the camera to be mounted to the ceiling or any wall securely. D-Link DCS-3415 Quick Install Guide...
-
Page 7: Software Installation
Software Installation Software Installation Turn on the computer and insert the D-Link DCS-3415 CD into the CD-ROM drive. The following step-by-step instructions displayed are shown when using Windows Vista operating system. The steps and ® screens are similar when using other Windows operating systems. ® Click Installation Wizard Click Next to continue. Click Next Click I Agree to accept the License Agreement. Click I Agree D-Link DCS-3415 Quick Install Guide... - Page 8 Software Installation To start the installation click Install. Note: The installation may take several minutes to complete. Click Install Click Finish to complete the installation. Click Finish D-Link DCS-3415 Quick Install Guide...
- Page 9 Configuring Your Camera with the Installation Wizard Click on the D-Link Installation Wizard icon that was created in your Windows Start menu. The Installation Wizard will appear and show the MAC address of your DCS-3415 and an IP Address (which may or may not be correct depending on what you have your DCS-3415 connected to). If you have a DHCP server on your network, there will be a valid IP Address displayed here. Note: A DHCP server is a device such as a router that automatically issues IP settings.
- Page 10 Configuration A new window will pop up to ask if you want to setup a PPPoE for the device. Click No for quick setup. For further information refer to the manual for details. Check the Get IP by DHCP Server Automatically box to obtain a new IP address every time the camera starts up. Click Next to continue. Click Next Select UPnP Port Forwarding if your router supports this function. If not, choose Manual to manually enter your port numbers. Click Next to continue. Click Next D-Link DCS-3415 Quick Install Guide...
- Page 11 Configuration Click Next to continue. Click Next A window will pop up asking you if you want to access the DCS-3415 via mobile phone. Clicking Yes will set the video resolution to 176x144. Click Apply to save and activate the settings listed in the window to the device. Application may take a few minutes to process. Click Apply D-Link DCS-3415 Quick Install Guide...
- Page 12 A window will pop up to confirm that the application was successfully configured. Click OK to continue. A new window will pop up displaying the links/addresses to access your device. Click Add to my favorite to save the address and then click Exit to complete the installation. Click Exit Double-click the DCS-3415 to launch the camera’s web configuration page. Note: Please refer to the user manual for more information. D-Link DCS-3415 Quick Install Guide...
- Page 13 Configuration Enter admin as the default username and leave the password blank. Click OK to continue. This section shows your camera’s live video. You can control your settings using the buttons at the bottom. For more information on using the web configuration, please refer to the user manual. D-Link DCS-3415 Quick Install Guide...
- Page 14 D-ViewCam Installation D-ViewCam software is included for the administrator to manage up to 32 D-Link IP cameras remotely. The administrator can use the software to configure the advanced settings for the camera. D-ViewCam is a complete management tool and includes all configurative settings. Insert the CD-ROM into the CD-ROM drive. A menu screen will appear as shown below. Click D-ViewCam D-ViewCam provides English, Traditional Chinese and Simplified Chinese language versions. Select a language version and click OK to continue. Click OK D-Link DCS-3415 Quick Install Guide...
- Page 15 C l i c k N e x t t o s t a r t t h e installation. Note: The D-ViewCam installation process may take several minutes to complete. Click Next D-Link DCS-3415 Quick Install Guide...
- Page 16 D-ViewCam Installation Click Finish to complete the installation. Click Finish D-Link DCS-3415 Quick Install Guide...
-
Page 17: Add A Camera
Adding a Camera Add a Camera To start D-ViewCam, click on Start > All Programs > D-Link > D-Link D-ViewCam Use admin as the default user name and leave the password blank. Click the (Check Box) to continue. Click The D-ViewCam screen will appear as shown below. Click (Next) to begin the Add Camera wizard. Click D-Link DCS-3415 Quick Install Guide... - Page 18 Adding a Camera Choose either to add camera(s) by automatically searching for camera(s) or to add camera(s) manually. If you select Auto Discovery, the system will search all available cameras that are located in the same subnet within the same LAN. The system will place all found cameras under the default map called My Map. Click Next to continue. If you choose Add Manually, you will need to enter the IP address of the camera. Click Next to continue. D-Link DCS-3415 Quick Install Guide...
- Page 19 • Non-Office Hours Only: Continuously monitor during non-office hours (06:00 PM to 08.00 AM), and ONLY record when motion is detected. Note: Excluding 24/7 Continuous Recording, other schedule recording types can ONLY do recording when motion is detected. Please refer to the user manual for more information. D-Link DCS-3415 Quick Install Guide...
- Page 20 D-ViewCam Installation Select Yes to add another camera, or select No to continue. Note: After you have finished adding your camera(s), click Close to view your camera(s). Your D-ViewCam Installation is Complete! D-Link DCS-3415 Quick Install Guide...
- Page 21 Notes Notes D-Link DCS-3415 Quick Install Guide...
- Page 22 Notes Notes D-Link DCS-3415 Quick Install Guide...
- Page 23 Notes Notes D-Link DCS-3415 Quick Install Guide...
-
Page 24: Technical Support
Copyright ©008 D-Link Corporation/D-Link Systems, Inc. All rights reserved. D-Link and the D-Link logo are registered trademarks of D-Link Corporation or its subsidiaries in the United States and other countries. Other trademarks are the property of their respective owners. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead lower actual data throughput rate.