Table of Contents
Advertisement
Available languages
Available languages
Gather
the required
tools and parts before starting installation.
Read and follow
the
instructions
provided
with
any tools listed here•
•
Flat-blade
screwdriver
•
#2 Phillips
screwdriver
•
Adjustable
wrench
that opens to 1"
(2.5 cm) or hex-head
socket wrench
(for adjusting
dryer feet)
•
Wire
stripper
(direct
wire installations)
•
I.evel
•
Vent clamps
•
Caulking
gun and compound
(for
installing
new exhaust
vent)
•
Tin snips/new
vent installations/
•
_/_" nut driver/recommended)
•
[_pe
measure
Are you placing
the dryer on a pedestal? You have the option
of purchasing
pedestals of
different
heights
separately
for this dryer. You may select a 10" (25.4 cm) pedestal
or a
15.5' (39.4 cm) pedestal
with a storage drawer• The pedestal
will add to the total height of the
dryer for a total
height of approximately
46" (116.8 cm) or 51.5'
(130.8 cm/, respectively.
For a garage installation,
you will need to place the 10' (25.4 cm) pedestal
at least
9' (22.9 cm) above the floor.
You will
need to place the 15.5" (_¢9.4 cm) pedestal
at least
3' (7.6 cm) above the floor.
Parts supplied
Remove parts packages
from dryer drum. Check that all parts are included.
4 Low, ling legs
NOTE: Do not use leveling
legs if installing
the dryer on a pedestal.
Parts needed
Check
local codes. Check existing
electrical
supply
and venting.
See "Electrical
Requirements"
and "Venting
Requirements"
before purchasing
parts.
•
For close-clearance
installations
between
31.5'
(80.01 cm) and 37' (93.98 cm), see "Plan
Vent System" section
for venting
requirements.
(9:3.98 era)
Mobile
home
installations
require metal exhaust
system hardware
available
for purchase
from
the dealer from whom you purchased
your dryer. For further
information,
please
refer to the
"Assistance
or Service"
section.
If using a power
supply
cord:
Use a U[. listed power
supply
cord kit marked
for use with
clothes
dryers. The kit should
contain:
•
A UI. listed 30-amp
power supply
cord, rated 120/240
volt minimum.
]he cord should
be
type SRD or SRDT and be at least 4 ft (1.22 m) long. ]he wires that connect
to the dryer
must end in ring terminals
or spade terminals
with
upturned
ends.
•
A UI. listed strain relief.
Optlonal pedestal f 1_._ /39.4 cm] model shown)
The pedestals
are available
in several colors.
lb order, call the dealer from whom you purchased
your dryer or refer to the "Assistance
or
Service"
section.
Pedestal Height
Color
Part Number
10" (25.4 cm)
White
MHP1000SQO
10" (25.4 cm)
Black
MHP1000SB0
15.5" (39.4 cm)
White
MHP1500SQ0
15.5" (39.4 cm)
Black
MHP1500SB0
15.5" (39.4 cm)
Pacific Blue
MHP1500SK0
Stack
Kit
Are you planning
to stack your washer
and dryer? To do so, you will need to purchase
a Stack
Kit. [b order, call the dealer from whom
you purchased
your dryer or refer to the "Assistance
or Service"
section.
Ask for Part Number
8212640.
Advertisement
Table of Contents
