Digicom S.p.A. The contents of this booklet may be modified without notice. Every possible care has been taken in testing and putting together all the documentation contained in this booklet, however Digicom can not take any responsability brought by the use of this booklet.
Digicom S.p.A. 1.0 GENERAL DESCRIPTION Digicom VoiceGATE is the ideal solution for the new Telecom Operators who want to take at home or office the new POTs with integration of Voice (Voice over IP) and Internet. VoiceGATE has 3 Ethernet ports (10/100) for the connection of local devices (Personal Computer, Printers, etc.), 2 analog ports and, optional, 1 SO ISDN bus with 2 RJ45 ports (for the connection ISDN...
Digicom S.p.A. 1.1 LED Description The VoiceGATE status can be checked through seven led indicators. Lan x Line x When all the LEDs are on, except the WAN led, it means the device is starting up. This operation takes about 45 seconds and takes place at the starting up, after a saving of the configuration or after a reset.
In the paragraph “VoiceGATE working test” you find the procedures to carry out your first tests with Digicom’s VoiceGATEs. Just few operations and you will be able to install and test two VoiceGATEs. Then all the configuration menus will be described.
Digicom S.p.A. 2.2 Access to configuration 1. Run the browser and connect to http://192.168.2.1. When the connection is established, the following window will appear: Insert in the User Name field: Insert in the Password field: NB: User name and password must be written with lower case.
Digicom S.p.A. Note: in case of problems while displaying the configuration, be sure that no proxy Server is active. In Microsoft Internet Explorer the Proxy setup is in: Tools, Internet Options, Connections LAN, Settings. Menù Description 1. General Configuration 2. Telephony Configuration 3.
Digicom S.p.A. 2.3 Save the configuration To confirm the new settings you must press the Submit button at the end of any WEB page. VoiceGATE To activate the modifications it is necessary, before you exit the configuration, to enter the Save settings menu and press the Submit button.
Digicom S.p.A. 2.4 VoiceGATE Working Test With simple operations you can test at once the working of VoiceGATE. We suggest to follow the procedures described in this chapter so to avoid working problems of VoiceGATE due to wrong configurations. The factory settings of VoiceGATE are the following: Ethernet: IP address: 192.168.2.1...
Digicom S.p.A. VoiceGATE Manual rev.2.0 2.5 Configuration Menù description General Information The information concerning the Hw and SW version and the elapsed time from the power on are displayed in this window. Pag. 11...
Digicom S.p.A. Telephony Configuration The voice information are displayed in this window, in particular: Call Setting: defines the Voice working mode. It can be set to work with the Gatekeeper or with the internal address book. Codec Selected: it allows to define the priority list for the codec, when the codec is set in Automatic.
Page 13
Digicom S.p.A. Interdigit Delay: wait in sec. from the last digit of the number, before starting the call. It is possible to activate the immediate dialling of the number, inserting the “#” character at the end of the number. Element in Gatekeeper: Gatekeeper IP address for registration.
Page 14
Digicom S.p.A. Supplementary Services The information concerning the reading and the voice supplementary service setup, according the H.450 standard, are displayed in this window. You will find here a brief description of the various supplementary services. For almost all the supplementary services it is necessary to hold on a call (H.450.4 service enabled).
Page 15
Digicom S.p.A. H.450.4 Call Hold H.450.4 service allows to put on hold a call and to call another number. Once the two calls have been activated, you can: • Press R + 1 -> To close the active call and recover the on hold call.
Digicom S.p.A. Public Network Configuration The information concerning the reading and the Wan (Uplink) parameters setup are displayed in this window. Use DHCP to obtain configuration IP Address: Subnet Mask: Dns List: Domain Name: Router List: Time Server List: Wan Leased Time:...
Digicom S.p.A. Private Network Configuration The information concerning the reading and the LAN part parameters are displayed in this window: Enable DHCP Server: IP Address: Subnet Mask: Address Pool List: IP Address Pool Mask: Router List: Dns List: Domain Name:...
Digicom S.p.A. Mac Addresses The Mac addresses of the device (Wan and LAN side) are displayed in this window. Public Network Mac: Private Network Mac: SNMP Agent The information concerning the reading and the parameter setup of SNMP protocol are displayed in this window.
Digicom S.p.A. The information concerning the reading and the parameters setup of the RIP protocol are displayed in this window. RIP: Silent Mode: Rip2 Mode: Timer Rate: Supply Interval: Expire Time: Garbage Time: VoiceGATE Enables/Disables the RIP OnlyRX – It manages the routing table in reception only RX+TX –...
Digicom S.p.A. VoiceGATE Manual rev.2.0 Route Table The informations concerning the routing table are displayed in this window. Security Configuration The informations concerning the password setup. Pag. 20...
Digicom S.p.A. Save Setting In this page it is possible to save the modified configuration via browser, clicking on the Submit button. VoiceGATE will restart to load the new configuration. After about 45 seconds it will be ready to be used.
Digicom S.p.A. 3.0 VoiceGATE.exe The VoiceGATE utility allows to : Create the “AddressBook” Load the AddressBook in the VoiceGATEs Upgrade the VoiceGATE firmware In the following parameters you will find some information on the use of the program; for further details refer to the Help on-line.
Page 23
Digicom S.p.A. VoiceGATE Manual rev.2.0 Gateway IP Address The IP Address field concerning the Gateway represents the IP Address of an eventual PSTN/ISDN Gateway. The Gateway allows the communication between the VoIP network and the traditional telephone lines (PSTN, ISDN and GSM). If the VoiceGATE doesn’t find the selected number in the address book, it sends it to the Gateway, that will call the selected number.
Digicom S.p.A. 3.2 Address Book Upgrade Through the Address Book Upgrade you can send the address book created with the Address Book Management. After selecting Address Book Upgrade choose the address book file to be sent. Insert the IP address, UserID and Password of the VoiceGATE to which you must send the address book, then confirm with ADD.
Digicom S.p.A. VoiceGATE Manual rev.2.0 Configuration Example Here is an example to use the VoiceGate and its configuration. In teh following application there are two VoiceGATE (one in the main office and the other one in the branch office) and no Gatekeeper is required. We will use the internal address book to configurate the VoiceGate.
Page 26
Digicom S.p.A. this menu insert information:: Alias The two telephone numbers If you yse the internal address book or the reference Gatekeeper. In this example we choose the Address book mode, setting parameter as Address Book. In the Public Network Configuration Menu you define the information concerning the VoiceGate WAN interface.
Page 27
Digicom S.p.A. VoiceGATE Manual rev.2.0 In the Private Network Configuration menu you define the information concerning the VoiceGate LAN interface. Besides the IP address and the SubnetMask, you have to enable the NAT. Configuration example of the PC Ethernet card to connect to the VoiceGate LAN ports.
Digicom S.p.A. VoiceGATE Configuration Work Sheet Installation: Company: Office: Hardware Information: Code: Serial Number: Telephony Configuration: H323 Alias: AddressBook: Phone Number Line 1 Number Codec Number Line 3 Number Codec Number Public Network Configuration: IP Address Private Network Configuration: IP Address...