Makita LW1400 Instruction Manual page 11

ASSEMBLY
OZD V EH V UH WKDW WKH WRRO LV
switched o and unplugged before carrying out
D ZRUN R WKH WRRO
2SH L J FH WHU FDS W SH VDIHW
J DUG
Country speci c
For the tools equipped with center cap type safety
guard, loosen the clamping screw rst then raise the
J DUG
► )LJ Clamping screw
2SH L J ( URSHD W SH VDIHW
J DUG
Country speci c
For the tools equipped with European type safety guard,
loosen the clamping screw rst then open the guard as
VKR
► )LJ Clamping screw
► )LJ
► )LJ
Removing or installing cut-o wheel
Be sure to tighten the toolless
FODPS RU KH EROW VHF UHO Insu cient tightening
may result in severe injury. When tightening the hex
bolt, use the socket wrench provided with the tool to
DVV UH SURSHU WLJKWH L J
OZD V VH R O WKH SURSHU L
and outer anges which are provided with the
WRRO
OZD V ORZHU WKH VDIHW J DUG
DIWHU UHSODFL J WKH ZKHHO
Wear gloves when handling
ZKHHOV
► )LJ
Inner ange 5L J
KHHO Outer ange
Hex bolt
)RU /:
5DLVH WKH VDIHW J DUG 7 U WKH WRROOHVV ODPS R
WHU OR N LVH KLOH KROGL J GR
remove the toolless clamp, outer ange and cut-o
wheel. When removing the cut-o wheel, do not remove
the inner ange as well as the ring and O-ring.
► )LJ
6KDIW OR N 7RROOHVV ODPS
To install the cut-o wheel, follow the removal proce
dures in reverse. Make sure to t the hole of cut-o
KHHO WR WKH UL J D G UHW U WKH VDIHW J DUG
)RU /:
Raise the safety guard. Turn the hex bolt counterclock
LVH VL J D VR NHW UH
shaft lock. Then remove the hex bolt, outer ange and
KHHO
► )LJ
7R L VWDOO WKH KHHO IROOR WKH UHPR DO SUR HG UHV L
reverse. Make sure to t the hole of cut-o wheel to the
UL J D G UHW U WKH VDIHW J DUG
23(5 7,21
cutting and maximum cutting e ciency can
EH GHWHUPL HG E WKH DPR
SURG FHG ZKLOH F WWL J 'R RW IRUFH WKH F W
by applying excessive pressure on the handle.
Reduced cutting e ciency, premature wheel wear, as
well as, possible damage to the tool, cut-o wheel or
RUNSLH H PD UHV OW
Hold the handle rmly. Switch on the tool and wait until
the cut-o wheel attains full speed before lowering
gently into the cut. When the cut-o wheel contacts
the workpiece, gradually bear down on the handle to
perform the cut. When the cut is completed, switch o
WKH WRRO D G wait until the cut-o wheel has come to
D FRPSOHWH VWRS before returning the handle to the fully
HOH DWHG SRVLWLR
0D LP P
WWL J D JOH D G RUNSLH H VKDSH
Max. cutting capacity with a brand-new cut-o
HU
ZKHHO
:RUNSLHFH VKDSH
2 UL J Cut-o
7RROOHVV ODPS
WKH VKDIW OR N 7KH
1
K KLOH KROGL J GR
6KDIW OR N Hex bolt
3URSHU KD GOH SUHVV UH G UL J
W RI VSDUNV WKDW LV
WWL J FDSDFLW
WWL J DSD LW DULHV GHSH GL J R WKH
WWL J D JOH
PP
PP
PP
PP
PP
PP
6
WKH
PP
PP
PP
PP