HIKVISION F6 - DashCam Manual

Packing List

1. Dashcam × 1
2. Car Charger × 1
3. Tape × 1
4. Power Cord × 1
5. Electrostatic Film × 1
6. User Manual × 1

Parts Introduction

1. Power Interface
2. Interface for 4G Box
3. Speaker
4. TF Card Slot
5. Recording Indicator (Red/Blue)
   • Solid blue light: Recording is normal.
   • Solid red light: Recording is abnormal.
   • Flashing light: The app is connected.
6. Bracket
7. Lens
8. Microphone
9. Reset Butt.on
   • Press Reset Button: Reboot the dashcam.
   • Hold Reset Button: When you hear the prompt sound, it means the dashcam is restored to defaults.

Installation

Clean the windscreen and paste the electrostatic film onto it.
Avoid introducing air bubble. DO NOT paste the film repeatedly.

Install the dashcam onto the center of the electrostatic film. Connect the dashcam with one end of the power cord along the red line shown in figure.

Connect the other end of power cord to car charger and connect car charger to cigarette lighter.

Adjust the surveillance angle and the installation is completed.

Mobile Phone Connection

1. Scan the QR code to download and install HikDashcam app.
   

2. Add the dashcam to the app.
   1. Run the HikDashcam app.
   2. Tap Wi-Fi Connection.
   3. In Wi-Fi list, select the Wi-Fi SSID of the target dashcam and enter Wi-Fi password to build a connection.

• You can set the parameters of the dashcam.
• For iOS, you need to go to Wi-Fi settings of your phone to connect to the Wi-Fi of dashcam.

3. Edit the dashcam password to activate it to avoid abnormal recording after connecting to Wi-Fi.
   Dashcam Wi-Fi default parameters:
   • Wi-Fi SSID: HIKVISION-F6-XXXX (XXXX refers to the last four characters of verification code.)
   • Wi-Fi password: 1234567890 (please edit password after logging in for the first time.)

Function Description

Power On and Power Off
Power On: When you starts up the engine, the dashcam powers on. Power Off: When you turn off the engine, the dashcam powers off.

• Make sure you have connected the dashcam to power according to Step 2 and Step 3 in Installation section.
• The power mode of cigarette lighter may vary by different vehicle types. Some may be powered constantly. In this case, please make sure that the dashcam stops after you turn off the vehicle engine. Otherwise, insufficient voltage may occur to vehicle battery.

Recording
Two recording types are provided: Normal Recording and Emergency Recording. Sound and mute recordings are selectable. Sound saving is set as default. You can turn off sound in app.

Specifications

Cautions

Safety Instruction

These instructions are intended to ensure that users can use the product correctly to avoid danger or property loss.

The precaution measure is divided into "Warnings" and "Cautions"

Serious injury or death may occur if any of the warnings are neglected.

Injury or equipment damage may occur if any of the cautions are neglected.

• In the use of the dashcam, you must be in strict compliance with the local laws and regulations.
• Keep the user manual properly for future reference. See initial connection of dashcam in user manual.
• Purchase the TF card from legal channel. To ensure safe and stable data transmission, it is recommended to use TF card of Class 10 or above.
• To protect TF card from damage, shut down the dashcam before installing and uninstalling TF card.
• If the dashcam is directly connected with the vehicle power system, you are recommended to power off the dashcam when the engine is off. Disconnect cigarette lighter to avoid insufficient voltage and abnormal startup. Reconnect cigarette lighter to ensure dashcam work normally when you start the car again.
• Operating temperature is from -20 ̊C to 70 ̊C (-4 ̊F to 158 ̊F). To protect the dashcam, DO NOT use it in high temperature, low temperature, or high-humidity environment. Keep the dashcam from rain and dust.
• The manual is subject to update. The functions of dashcam may vary according to different models.

Troubleshooting